- increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
- use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
- remove "Unlock Bypass" mode, because macronix flashes do not support
this mode officially
- fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
for Intel compatible flashes, not for AMD compatible.
Patch by Martin Krause, 15 Feb 2006
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Some code cleanup
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
Patch by Martin Krause, 8 Jun 2006
This patch supports two serial consoles on boards with
a MPC5xxx CPU. The console can be switched at runtime
by setting stdin, stdout and stderr to the desired serial
interface (serial0 or serial1). The PSCs to be used as
console port are definded by CONFIG_PSC_CONSOLE
and CONFIG_PSC_CONSOLE2.
See README.serial_multi for details.
If the bus is blocked because of a previously interrupted
transfer, up to eleven clocks are generated on the I2CSCL
line to complete the transfer and to free the bus.
With this fix pin I2CSCL (PG6) is really configured as GPIO
so the clock pulses are really generated.
Patch by Martin Krause, 04 Apr 2006
Patch by Martin Krause, 07 Nov 2005
Tested on a STK85XX baseboard. Make sure the PS/2 controller
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
Patch by Martin Krause, 08 Nov 2005
In tsc2000_read_channel() the delay after setting the multiplexer
to a temperature channel is increased from 1,5 ms to 10 ms. This
is to allow the multiplexer inputs to stabilize after huge steps
of the input signal level.
Make the automatic CS configuration the default.
The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
and CONFIG_TQM5200_AC are removed.
"TQM5200_config" is now the default for STK52XX.200 base boards.
On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
Patch by Martin Krause, 07 Nov 2005
The environment variable "ver" is now set before
do_auto_update() is called, so that "ver" can be used
in USB update scripts.
Patch by Martin Krause, 27 Oct 2005
-When booting from an epcs controller, the epcs bootrom may leave the
slave select in an asserted state causing soft reset hang. This
patch ensures slave select is negated at reset.
Patch by Scott McNutt, 08 Jun 2006
-Fix asm/io.h macros
-Eliminate use of CACHE_BYPASS in cpu code
-Eliminate assembler warnings
-Fix mini-app stubs and force no small data
Patch by Scott McNutt, 08 Jun 2006
We use the "automatic" mode that was used for the MPC8266ADS and
MPC8272 boards. Eventually this should be used on all boards?]
Patch by Wolfgang Grandegger, 17 Jan 2006
- Add IXP4xx NPE ethernet MAC support
- Add support for Intel IXDPG425 board
- Add support for Prodrive PDNB3 board
- Add IRQ support
Patch by Stefan Roese, 23 May 2006
[This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still
sufferes from licensing issues. Blame Intel.]
Problems have been seen in the linux kernel's smc91x network driver
due to improper bus timings. The latest 2.6 OMAP kernels currently
have a workaround, but this fix belongs in u-boot.
Patch by Kevin Hilman, 13 Oct 2005
- Fix OMAP support that omap5912osk compiles in current source tree
- Update with code from "http://omap.spectrumdigital.com/osk5912"
to fix problems with DDR initialization
- Fix timer setup
- Use CFI flash driver and support complete 32MB of onboard flash
- Add "print_cpuinfo()" and "checkboard()" functions to display
CPU (with frequency) and Board infos
Patch by Stefan Roese, 10 May 2006
- Removed MPC8349ADS port
- Added PCI support to MPC8349ADS
- reworked memory map to allow mapping of all regions with BATs
Patch by Kumar Gala 20 Apr 2006
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Patch from Scott McNutt 11, Aug 2005
-When booting from an epcs controller, the epcs bootrom may leave the
slave select in an asserted state causing soft reset hang. This
patch ensures slave select is negated at reset.
Patch by Scott McNutt 11, Aug 2005
-Fix asm/io.h macros
-Eliminate use of CACHE_BYPASS in cpu code
-Eliminate assembler warnings
-Fix mini-app stubs and force no small data
relocate ichache_State to ram
u-boot can run from internal flash
Add EB+MCF-EV123 board support.
Add m68k Boards to MAKEALL
Patch from Jens Scharsig, 08 Aug 2005
- Fix dbau1x00 boards broken by dbau1550 patch
PLL:s were not set for boards other than 1550.
Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.
Default boot is now bootp for cards other than 1550.
Patch by Thomas Lange Aug 10 2005
- fix some compiler/parser error, if using m68k tool chain
- optical fix for protect on/off all messages, if using more
then one bank
Patch by Jens Scharsig, 28 July 2005
- Add Intel legacy lock/unlock support to common CFI driver
On some Intel flash's (e.g. Intel J3) legacy unlocking is
supported, meaning that unlocking of one sector will unlock
all sectors of this bank. Using this feature, unlocking
of all sectors upon startup (via env var "unlock=yes") will
get much faster.
- Fixed problem with multiple reads of envronment variable
"unlock" as pointed out by Reinhard Arlt & Anders Larsen.
- Removed unwanted linefeeds from "protect" command when
CFG_FLASH_PROTECTION is enabled.
- Changed p3p400 board to use CFG_FLASH_PROTECTION
Patch by Stefan Roese, 01 Apr 2006
* Changes/fixes for drivers/cfi_flash.c:
- Correctly handle the cases where CFG_HZ != 1000 (several
XScale-based boards)
- Fix the timeout calculation of buffered writes (off by a
factor of 1000)
Patch by Anders Larsen, 31 Mar 2006
405 SDRAM: - The SDRAM parameters can now be defined in the board
config file and the 405 SDRAM controller values will
be calculated upon bootup (see PPChameleonEVB).
When those settings are not defined in the board
config file, the register setup will be as it is now,
so this implementation should not break any current
design using this code.
Thanks to Andrea Marson from DAVE for this patch.
440 DDR: - Added function sdram_tr1_set to auto calculate the
TR1 value for the DDR.
- Added ECC support (see p3p440).
Patch by Stefan Roese, 17 Mar 2006
CFG_BOOTM_LEN to adjust this setting.
As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
uImages was restricted to 4MBytes. This default size is now
increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
in the board config file.
Patch by Stefan Roese, 13 Mar 2006
- add support for Analog Devices Blackfin BF533 CPU
- add support for the ADI BF533 Stamp uClinux board
- add support for the ADI BF533 EZKit board
Patches by Richard Klingler, June 11th 2005:
- Use correct flash sector size
- Use correct memory test end address
- Add support for bzip2 compression
- Various small fixes
Patch by Yuli Barcohen, 05 Jun 2005
- Fix SDRAM timing on both local bus and 60x bus
- Add support for second flash bank (SIMM)
- Change boot flash base
Patch by Yuli Barcohen, 05 Jun 2005
* Add env-variable "unlock" to handle initial state of sectors
(locked/unlocked).
Only the U-Boot image and it's environment is protected,
all other sectors are unprotected (unlocked) if flash
hardware protection is used (CFG_FLASH_PROTECTION) and
the environment variable "unlock" is set to "yes".
Patch by Stefan Roese, 28 Feb 2006
* Update drivers/cfi_flash.c:
- find_sector() called in both versions of flash_write_cfiword()
Patch by Peter Pearse, 27th Feb 2006
* CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode
Patch by Jose Maria Lopez, 16 Jan 2006
* Add support for AMD/Spansion Flashes in flash_write_cfibuffer
Patch by Alex Bastos and Thomas Schaefer, 2005-08-29
* Changes/fixes for drivers/cfi_flash.c:
We *should* check if there are any error bits if the previous call
returned ERR_OK (Otherwise we will have output an error message in
flash_status_check() already.) The original code would only check for
error bits if flash_status_check() returns ERR_TIMEOUT.
Patch by Marcus Hall, 23 Aug 2005
* Changes/fixes for drivers/cfi_flash.c:
- Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c
- Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c
Patch by Sangmoon Kim, 19 Aug 2005
* Fixes for drivers/cfi_flash.c:
- Fix wrong timeout value usage in flash_status_check()
- Round write_tout up when converting to msec in flash_get_size()
- Remove clearing flash status at the end of flash_write_cfibuffer()
which sets Intel 28F640J3 flash back to command mode on CSB472
Patch by Tolunay Orkun, 02 July 2005
As done in the linux kernel, the U-Boot version (U_BOOT_VERSION)
of all unreleased (untagged) U-Boot images will be automatically
extended upon compiletime with a part of the GIT commit ID and
possibly with "dirty" if uncommited changes are detected.
Here an example for the resulting version:
"U-Boot 1.1.4-g3457ac18-dirty"
The version is now maintained in the toplevel Makefile and the
version headers are autogenerated.
Patch by Stefan Roese, 9 Feb 2006
