dm_test_restore() is called after dm unit test is run.
But this function does not scan any nodes under /firmware since
it calls dm_scan_fdt().
This causes an issue. For instance, scmi_sandbox_agent device
will disappear after running 'ut dm scmi_sandbox_agent'.
So call dm_extended_scan() instead. This change will be coherent
with what dm_scan() and test_pre_run() does.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is pretty messy at present since it relies on a SPL_SANDBOX option
that does not exist. Use the normal options instead, so that it will work
with split config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and they can create a lot of noise. Add a way
to disable them. Use that in tests, with a flag provided to enable them
for tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and can create a lot of noise. Add a way to
disable them. Use that in tests, with a flag provided to enable them for
tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
We must call dm_scan_other() after devices from the device tree have been
created, since that function behaves differently if there is no bootstd
device.
Adjust the logic to achieve this.
Also fix the bootflow_system() test which was relying on this broken
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running unit tests, some may have side effects which cause a
subsequent test to break. This can sometimes be seen when using 'ut dm'
or similar.
Add a new argument which allows a particular (failing) test to be run
immediately after a certain number of tests have run. This allows the
test causing the failure to be determined.
Update the documentation also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests access data in block devices and so cause the cache to fill
up. This results in memory being allocated.
Some tests check the malloc usage at the beginning and then again at the
end, to ensure there is no memory leak caused by the test. The block cache
makes this difficult, since the any test may cause entries to be allocated
or even freed, if the cache becomes full.
It is simpler to clear the block cache after each test. This ensures that
it will not introduce noise in tests which check malloc usage.
Add the logic to clear the cache, using the existing blkcache_invalidate()
function. Drop the duplicate code at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently, we must call cyclic_init() at some point before
cyclic_register() becomes possible. That turns out to be somewhat
awkward, especially with SPL, and has resulted in a watchdog callback
not being registered, thus causing the board to prematurely reset.
We already rely on gd->cyclic reliably being set to NULL by the asm
code that clears all of gd. Now that the cyclic list is a hlist, and
thus an empty list is represented by a NULL head pointer, and struct
cyclic_drv has no other members, we can just as well drop a level of
indirection and put the hlist_head directly in struct
global_data. This doesn't increase the size of struct global_data,
gets rid of an early malloc(), and generates slightly smaller code.
But primarily, this avoids having to call cyclic_init() early; the cyclic
infrastructure is simply ready to register callbacks as soon as we
enter C code.
We can still end up with schedule() being called from asm very early,
so we still need to check that gd itself has been properly initialized
[*], but once it has, gd->cyclic_list is perfectly fine to access, and
will just be an empty list.
As for cyclic_uninit(), it was never really the opposite of
cyclic_init() since it didn't free the struct cyclic_drv nor set
gd->cyclic to NULL. Rename it to cyclic_unregister_all() and use that
in test/, and also insert a call at the end of the board_init_f
sequence so that gd->cyclic_list is a fresh empty list before we enter
board_init_r().
A small piece of ugliness is that I had to add a cast in
cyclic_get_list() to silence a "discards 'volatile' qualifier"
warning, but that is completely equivalent to the existing handling of
the uclass_root_s list_head member.
[*] I'm not really sure where we guarantee that the register used for
gd contains 0 until it gets explicitly initialized, but that must be
the case, otherwise testing gd for being NULL would not make much sense.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mm-venice-*
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is possible for a test to skip itself by returning -EAGAIN
but this is not recorded. An existing example is in test_pre_run() with
the "Console recording disabled" check.
Keep a track of skipped tests and report the total at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We already have a function for probing all devices of a specific class,
use it.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there is only one device tree used by the ofnode functions,
except for some esoteric use of live tree. In preparation for supporting
more than one, add a way to reset the list of device trees.
For now this does nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test flag which indicates that the 'other' FDT should be set up
ready for use. Handle this by copying in the FDT, unflattening it for
livetree tests. Free the structures when the tests have run.
We cannot use the other FDT unless we are using live tree or
OFNODE_MULTI_TREE is enabled, since only one tree is supported by the
ofnode interface in that case. Add this condition into
ut_run_test_live_flat() and update the comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the device tree changes during a test and we cannot restore it, mark
it as such so that future tests which need the live tree are skipped.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the flat device tree changes it can mess up the live tree since that
uses the flat tree for its strings. This affects only a few sandbox tests
which modify the device tree, but the number will grow as ofnode support
for writing improves.
While the control FDT is not intended to change while U-Boot is running,
some tests do so. For example, the ofnode interface only supports
modifying properties in the control FDT, so tests must use that.
To solve this problem, keep a copy of the FDT and restore it as needed
when the test is finished. The copy only happens on sandbox (except SPL
builds), to reduce memory usage and because these tests are not useful on
other boards. For other boards, a checksum is taken to ensure that nothing
changes.
It would be possible to always checksum the FDT on sandbox and only
restore it if needed, but this is slightly slower than restoring it every
time, at least with crc8.
Move the code which checks for success to the very end, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to test that out-of-memory checks work correctly in code
that calls malloc().
Add a simple way to force failure after a given number of malloc() calls.
Fix a header guard to avoid a build error on sandbox_vpl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
At present the live tree tests are not run on sandbox. This bug is in two
parts, with a duplicate flag value and incorrect logic in the test runner.
This was not noticed because the bug was fixed in a later commit and does
not cause test failures.
Fix this.
Fixes: 7b1dfc9fd7 ("dm: core: Prepare for updating the device tree with ofnode")
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function is not called, so tests miss out on any devices
created by it. Add it in so that tests can rely on these extra devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some documentation and a new flag so that we can safely enabled using
the ofnode interface to write to the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is easier to read the positive conditional.
While at it, convert hard coded length of "_test_" to strlen("_test_")
which will be converted to a constant bu optimizing compiler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When run `ut dm [test name]` allow to use simple pattern to run all tests
started with given prefix. For example, to run all ACPI test cases:
ut dm acpi*
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to a recent change, tests are limited to running on sandbox only.
Correct this so that any architecture can run them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Sean Anderson <seanga2@gmail.com>
Fixes: c79705ea93 ("test: Move dm_test_init() into test-main.c")
Tested-by: Sean Anderson <seanga2@gmail.com>
It is not possible to destroy the uclasses when they are created at
build time. Skip this step so that SPL test can complete successfully.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present SPL only runs driver model tests. Update it to run all
available tests, i.e. in any test suite.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add this functionality to ut_run_list() so it can be removed from
dm_test_run().
At this point all tests are run through ut_run_list().
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a check to ut_run_list() as to whether a list has driver model tests.
Move the logic for the test devicetree into that function, in an effort
to eventually remove all logic from dm_test_run().
Signed-off-by: Simon Glass <sjg@chromium.org>
Use this function instead of implementing it separately for driver model.
Make ut_run_tests() private since it is only used in test-main.c
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a global test state for all driver-model tests. Make use
of a local struct like we do with the other tests.
To make this work, add functions to get and set this state. When a test
starts, the state is set (so it can be used in the test). When a test
finishes, the state is unset, so it cannot be used by mistake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model tests are generally run twice, once with livetree enable and
again with it disabled. Add a function to handle this and call it from the
driver model test runner.
Make ut_run_test() private since it is not used outside test-main.c now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of having a separate function for running driver model tests, use
the common one. Make the pre/post-run functions private since we don't
need these outside of test-main.c
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function into the common test runner and rename it to
dm_test_post_run() so that its purpose is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function into test-main so that all the init is in one place.
Rename it so that its purpose is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
For driver model tests we want to reinit the data structures so that
everything is in a known state before the test runs. This avoids one test
changing something that breaks a subsequent tests.
Move the call for this into test_pre_run().
Signed-off-by: Simon Glass <sjg@chromium.org>
We already have a function for silencing the console during tests. Use
this from test_pre_run() and drop this code from the driver model tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Ultimately we want to get rid of the special driver model test init and
use test_pre_run() and test_post_run() for all tests. As a first step,
use those function to handle console recording.
For now we need a special case for setting uts->start, but that wil go
away once all init is in one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split out the test preparation into a separation function before
expanding it. Add a post-run function as well, currently empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new test runner that will eventually be able to run any test. For
now, have it run the 'command' unit tests, so that the functionality in
cmd_ut_category() moves into it.
Signed-off-by: Simon Glass <sjg@chromium.org>
