This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On platforms that use CONFIG_USB_OHCI_NEW we do not need to set
CONFIG_SYS_USB_OHCI_REGS_BASE nor CONFIG_SYS_USB_OHCI_SLOT_NAME. Drop
these from platforms that we can.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The AST2600 has a Qemu model that allows testing. Create a SPI NOR image
containing the combined SPL and u-boot FIT image.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The generic arm linker script contains this section:
.bss __rel_dyn_start (OVERLAY) : {
...
}
The (OVERLAY) syntax in the description causes the .bss section to be
included in the NOR area of the image:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
0000c61c l d .bss 00000000 .bss
0000c640 l O .bss 00000040 __value.0
0000c68c g O .bss 00000000 __bss_end
0000c61c g O .bss 00000000 __bss_start
0000c680 g O .bss 0000000c stdio_devices
This is what the custom linker script tries to avoid, as the NOR area is
read-only.
Remove the OVERLAY syntax to fix the BSS location:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
83000000 l d .bss 00000000 .bss
83000000 l O .bss 00000040 __value.0
0000c61c g O .bss 00000000 __image_copy_end
8300004c g O .bss 00000000 __bss_end
83000000 g O .bss 00000000 __bss_start
83000040 g O .bss 0000000c stdio_devices
This restores the state of the linker script before the patch that fixed
the linker lists issue.
Fixes: f6810b749f ("aspeed/ast2600: Fix SPL linker script")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The normal way of loading u-boot is as a FIT, so configure u-boot.img as
the SPL playload.
The u-boot-with-spl.bin target will add padding according to
CONFIG_SPL_MAX_SIZE which defaults to 64KB on the AST2600.
With this the following simple steps can be used to build and boot a
system:
make u-boot-with-spl.bin
truncate -s 64M u-boot-with-spl.bin
qemu-system-arm -nographic -M ast2600-evb \
-drive file=u-boot-with-spl.bin,if=mtd,format=raw
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 bootrom has a max size of 64KB. This can be overridden if the
system is running the SPL from SPI NOR and not using secure boot.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The HACE driver lacks support for all the hash types, causing boot to
fail with the default FIT configuration which uses CRC32.
Additionally the Qemu model or the u-boot driver is unable to correctly
compute the SHA256 hash used in a FIT.
Disable HACE by default while the above issues are worked out to enable
boot testing in Qemu.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allows loading one u-boot from another. Useful for testing on hardware.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Useful for testing images with the default hash type.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Aspeed SDHCI controller is arranged with some shared control
registers, followed by one or two sets of actual SDHCI registers.
Adjust the driver to probe this controller device first. The driver then
wants to iterate over the child nodes to probe the SDHCI proper:
ofnode node;
dev_for_each_subnode(node, parent) {
struct udevice *dev;
int ret;
ret = device_bind_driver_to_node(parent, "aspeed_sdhci",
ofnode_get_name(node),
node, &dev);
if (ret)
return ret;
}
However if we did this the sdhci driver would probe twice; once
"naturally" from the device tree and a second time due to this code.
Instead of doing this we can rely on the probe order, where the
controller will be set up before the sdhci devices. A better solution is
preferred.
Select MISC as the controller driver is implemented as a misc device.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The reset control was written for the ast2500 and directly programs the
clocking register.
So we can share the code with other SoC generations use the reset device
to deassert the I2C reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The I2C driver shares a reset line between buses, so allow it to test
the state of the reset line before resetting it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The EVB has an EEPROM on bus 3 and a LM75 temp sensor on bus 7. Enable
those busses we can test the I2C driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The same as the upstream Linux device tree, each i2c bus has a property
specifying the reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set the pinctrl groups for each I2C bus. These are essential to
I2C operating correctly.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Anytime a new revision of a chip is produced, Texas Instruments
will increment the 4 bit VARIANT section of the CTRLMMR_WKUP_JTAGID
register by one. Typically this will be decoded as SR1.0 -> SR2.0 ...
however a few TI SoCs do not follow this convention.
Rather than defining a revision string array for each SoC, use a
default revision string array for all TI SoCs that continue to follow
the typical 1.0 -> 2.0 revision scheme.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Add new Toradex MAC OUI (8c:06:cb), to the config block. With this change
we extend the possible serial-numbers as follows:
For serial-numbers 00000000-16777215 OUI 00:14:2d is taken
For serial-numbers 16777216-33554431 OUI 8c:06:cb is taken
Lower 24-bit of the serial number are used in the NIC part of the
MAC address, the complete serial number can be calculated using the OUI.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Do 1 byte address checks first prior to doing 2 byte address checks.
When performing 2 byte addressing on 1 byte addressing eeprom, the
second byte is taken in as a write operation and ends up erasing the
eeprom region we want to preserve.
While we could have theoretically handled this by ensuring the write
protect of the eeproms are properly managed, this is not true in case
where board are updated with 1 byte eeproms to handle supply status.
Flipping the checks by checking for 1 byte addressing prior to 2 byte
addressing check prevents this problem at the minor cost of additional
overhead for boards with 2 byte addressing eeproms.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to supply chain issues, we are starting to see a mixture of eeprom
usage including the smaller 7-bit addressing eeproms such as 24c04
used for eeproms.
These eeproms don't respond well to 2 byte addressing and fail the
read operation. We do have a check to ensure that we are reading the
alternate addressing size, however the valid failure prevents us
from checking at 1 byte anymore.
Rectify the same by falling through and depend on header data comparison
to ensure that we have valid data.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The eeprom data area is much bigger than the data we intend to store,
however, with bad programming, we might end up reading bad records over
and over till we run out of eeprom space. instead just exit when 10
consecutive records are read.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Static DMA channel data for R5 SPL is mostly board agnostic so use SOC
configs instead of EVM specific config to ease adding new board support.
Drop J7200 EVM specific settings as its same as J721e
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add CONFIG_NR_DRAM_BANKS from am62x_evm_a53_defconfig as this is
needed to calculate the size of DDR that is available.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Call into k3-ddrss driver to fixup device tree and resize
the available amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup
as done from R5 SPL and apply it to DT passed to A53 U-boot,
which in turn passes this to the OS.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the appropriate fdtdec_setup_mem_size_base() call in
dram_init() and fdtdec_setup_bank_size() in dram_bank_init()
to pull these values from DT, where they are already available,
instead of hardcoding them.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The spl_enable_dcache() function calls dram_init_banksize()
to get the total memory size. Normally the dram_init_banksize()
setups the memory banks, while the total size is reported
by ddr_init(). This worked so far for K3 since we set the
gd->ram_size in dram_init_banksize() as well.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
