Not really qcom specific, but for now qcom/lk is the one firmware that
is (afaiu) setting up the appropriate dt node for pre-configured
display. Uses the generic simple-framebuffer DT bindings so this should
be useful on other platforms.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The STM32 LTDC display controller provides a parallel digital RGB and
signals for horizontal, vertical synchronization, Pixel Clock and Data
Enable as output to interface directly to a variety of LCD and TFT panels.
The LTDC main features are:
- 24-bit RGB Parallel Pixel Output, Programmable timings & polarity for
HSync, VSync and Data Enable.
- 2 layers with Blending, Color Keying, Window position & size,
Dithering, Background color, Color Look-Up Table (CLUT).
- Supported layer color formats: ARGB8888, RGB888, RGB565, ARGB1555,
ARGB4444, L8 CLUT, AL44 & AL88
This LTDC driver:
- supports: RGB parallel output with timings & polarity, 1 layer
in RGB565.
- supports but with hard-coded configurations: blending, window
position & size (crop), background color.
- does not support yet: rgb888, argb8888, 8-bit clut, dithering.
This LTDC driver is compatible with all stm32 platforms with the
LTDC IP and has been tested on stm32 f746-disco board.
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Add a driver for GPIO backlights.
It understands the standard device tree binding.
It can be used with simple-panel when PWM is not necessary.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a config to select individually the driver for PWM backlights.
Manage "depends on" to be backyard compatible.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Instead of having drivers/video/rockchip/Kconfig point outside of its
hierarchy for dw_hdmi.o, we should use a configuration-option to
include the Designware HDMI support.
This change introduces a new config option (not to be selected via
menuconfig, but to be selected from a dependent video driver's
configuration option) that enables dw_hdmi.o and selects it whenever
the HDMI support for Rockchip SoCs is selected.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
1. add Kconfig for rockchip video driver, so that video port can be
selected as needed.
2. move VIDEO_ROCKCHIP option to new Kconfig for concision.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop indenting in Kconfig:
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.
Ideas has been taken from the sunxi display driver, e.g.
20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_SCROLL_LINES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_EXTRA_INFO
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_SW_CURSOR
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-convert, find all the cases where this is off]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VGA_AS_SINGLE_DEVICE
Once we migrate to driver model for video, we should be able to drop this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_BG_COL
CONFIG_SYS_CONSOLE_FG_COL
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CFB_CONSOLE_ANSI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This converts the following to Kconfig:
CONFIG_VIDEO
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
At present we use the legacy vesa driver for graphics. Add a driver which
supports driver model. This can be probed only when needed, removing the
need to start up the display if it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a video driver for Intel's broadwell integrated graphics controller.
This uses a binary blob for most init, with the driver just performing a few
basic tasks.
This driver supports VESA as the mode-setting mechanism. Since most boards
don't support driver model yet with VESA, a special case is added to the
Kconfig for broadwell. Eventually all boards will use driver model and this
can be removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
We can check this in Kconfig now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards with a saved environment may use 'lcd' in their stdout environment
variable, expecting that this will enable output to the LCD. When the board
moves to use driver model for video, this will no-longer work. Add a
work-around to fix this. A warning messages is printed, and we will remove
the work-around at the end of 2016.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
The existing 8x16 font is adequate for most purposes. It is small and fast.
However for boot screens where information must be presented to the user,
the console font is not ideal. Common requirements are larger and
better-looking fonts.
This console driver can use TrueType fonts built into U-Boot, and render
them at any size. This can be used in scripts to place text as needed on
the display.
This driver is not really designed to operate with the command line. Much
of U-Boot expects a fixed-width font. But to keep things working correctly,
rudimentary support for the console is provided. The main missing feature is
support for command-line editing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds basic support for the LCD controller of the Marvell
Armada XP SoC.
An AXP based custom board port will be added later, to use this
driver to display a splash screen via the bmp command later.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some Rockchip SoCs support HDMI output. Add a display driver for this so
that these displays can be used on supported boards.
Unfortunately this driver is not fully functional. It cannot reliably read
EDID information over HDMI. This seems to be due to the clocks being
incorrect - the I2C bus speed appears to be up to 100x slower than the
clock settings indicate. The root cause may be in the clock logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current DisplayPort uclass is too specific. The operations it provides
are shared with other types of output devices, such as HDMI and LVDS LCD
displays.
Generalise the uclass so that it can be used with these devices as well.
Adjust the uclass to handle the EDID reading and conversion to
display_timing internally.
Also update nyan-big which is affected by this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig. This is quite simple as only sandbox uses the
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Sometimes the console must be rotated. Add a driver which supports rotating
the text clockwise to 90, 180 and 270 degrees. This can support devices
where the display is rotated for mechanical reasons.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
U-Boot has separate code for LCDs and 'video' devices. Both now use a
very similar API thanks to earlier work by Nikita Kiryanov. With the driver-
model conversion we should unify these into a single uclass.
Unfortunately there are different features supported by each. This
implementation provides for a common set of features which should serve
most purposes. The intent is to support:
- bitmap devices with 8, 16 and 32 bits per pixel
- text console wih white on black or vice versa
- rotated text console
- bitmap display (BMP format)
More can be added as additional boards are ported over to use driver model
for video.
The name 'video' is chosen for the uclass since it is more generic than LCD.
Another option would be 'display' but that would introduce a third concept
to U-Boot which seems like the wrong approach.
The existing LCD and video init functions are not needed now, so this uclass
makes no attempt to implement them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add support for the ANX9804 bridge chip, which can take pixel data coming
from a parallel LCD interface and translate it on the fly into a DP
interface for driving eDP TFT displays. It uses I2C for configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
A video bridge typically converts video from one format to another, e.g.
DisplayPort to LVDS. Add driver model support for these with a simple
interface to control activation and backlight. The uclass supports GPIO
control of power and reset lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no reason to prevent CONFIG_VIDEO_VESA driver working on
non-x86 boards, so remove such limitation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Connect up the clocks and the eDP driver to make these displays work with
Tegra124-based devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
eDP (Embedded DisplayPort) is a standard widely used in laptops to drive
LCD panels. Add a uclass for this which supports a few simple operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that we have a full VESA driver we may as well use that. We need to
support the VESA layer being set up by early start-up code or by
running a VGA ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver intended to cope with any VESA-compatible x86 graphics
adapter. It will not support ROMs which use OpenFirmware (Forth) since
there is no support for that in U-Boot. This means that MAC OS cards
will not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Instead of using the internal 'tx_clk' clock source, it is also
possible to use the pixel clock signal from the parallel LCD
interface ('pclk') as the reference clock for PLL.
The 'tx_clk' clock speed may be different on different boards/devices
(the allowed range is 8MHz - 30MHz). Which is not very convenient,
especially considering the need to know the exact 'tx_clk' clock
speed. This clock speed may be difficult to identify without having
device schematics and/or accurate documentation/sources every time.
Using 'pclk' is free from all these problems.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SSD2828 can take pixel data coming from a parallel LCD interface
and translate it on the fly into MIPI DSI interface for driving
a MIPI compatible TFT display. SSD2828 is configured over SPI
interface, which may or may not have MISO pin wired up on some
hardware. So a write-only SPI mode also has to be supported.
The SSD2828 support code is implemented as a utility function
and needs to be called from real display drivers, which are
responsible for driving parallel LCD hardware in front of the
video pipeline. The usage instructions are provided as comments
in the header file.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.
Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.
To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
