Commit graph

25 commits

Author SHA1 Message Date
Tom Rini
554e5514ac configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10 15:31:07 -04:00
Tom Rini
f7d0ae9c63 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 08:46:52 -04:00
Jagan Teki
8d7192cb7f arm64: dts: rockchip: Add ROCKPi 4A/4B support
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.

- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
  GPIO pin change compared to 4B, 4C

So move common nodes, properties into dtsi file and include
on respective variant dts files.

Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00
Jagan Teki
7ff3fc57ad rockchip: rock-pi-4: Enable HDMI output
Enable config options to get HDMI output on RockPI-4 boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:21:44 +08:00
Jagan Teki
be4d6b03c0 rockchip: rock-pi-4: Enable USB Gadget
Enable USB gadget for rock-pi-4 boards.

This would help to use fastboot by default.

Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:21:42 +08:00
Jagan Teki
8489b4e10d rockchip: rock-pi-4: Enable PCI/NVME
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.

=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
            Type: Hard Disk
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:21:39 +08:00
Jagan Teki
cd7bf74e0e rockchip: rock-pi-4: Enable USB3 Host
Enable USB3.0 Host support for RockPI-4 boards.

Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.

Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
  1  Hub (480 Mb/s, 0mA)
     u-boot EHCI Host Controller

  1  Hub (480 Mb/s, 0mA)
     u-boot EHCI Host Controller

  1  Hub (5 Gb/s, 0mA)
     U-Boot XHCI Host Controller

  1  Hub (5 Gb/s, 0mA)
  |  U-Boot XHCI Host Controller
  |
  +-2  Mass Storage (5 Gb/s, 224mA)
       SanDisk Dual Drive 040130e3ee554b7078843f4eb331646

Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:21:31 +08:00
Kever Yang
dfb2889cd4 rockchip: rk3399: add target type for evb based board
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-20 09:18:14 +08:00
Jagan Teki
d49d8aa272 rockchip: rk3399: Enable DISPLAY_CPUINFO
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30 11:44:01 +08:00
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
086e391bc4 Merge tag 'u-boot-rockchip-20191110' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
2019-11-11 14:19:32 -05:00
Kever Yang
006ab58d46 rockchip: rk3399: update SPL_STACK_R_ADDR
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.

After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Kever Yang
5ce94c74a6 rockchip: rk3399: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.

Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.

The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Tom Rini
bf17bcc5b1 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 12:03:24 -04:00
Rohan Garg
015c3fbad9 rockchip: rk3399: Enable CONFIG_MISC_INIT_R for the Rock PI 4
This enables us to set a static MAC address

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 18:15:31 +08:00
Kever Yang
58ec0aa361 rockchip: rk3399: defconfig: remove SPL raw image support
RK3399 SPL only support FIT image for ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Tom Rini
df33f86468 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-14 08:11:27 -04:00
Kever Yang
a13f870ad4 rockchip: rk3399: default enable SPL LIBCOMMON and LIBGENERIC
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Kever Yang
d0ae3bc4d6 rockchip: rk3399: use default value for SYS_MALLOC_F_LEN
There is no difference in rk3399 board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
ecd8136e52 configs: rock-pi-4: Enable LPDDR4 support
Due to foot-print issues, we have LPDDR4 code can be
marked as CONFIG_RAM_RK3399_LPDDR4.

So, enable it for Rock-PI-4 board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21 00:00:38 +08:00
Tom Rini
f512851413 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-21 10:11:23 -04:00
Jagan Teki
540c900dec rockchip: rk3399: Add Rock PI 4 support
Add initial support for Rock PI 4 board.

Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type

Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)

Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-30 18:22:35 +08:00