Add a new implementation of soft_spi that uses device tree to specify the
GPIOs. This will replace soft_spi_legacy for boards which use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This feature provides for init of a single SPI port for the soft SPI
feature. It is not really compatible with driver model since it assumes a
single SPI port. Also, inserting SPI init into the driver by means of
a #define is not very nice.
This feature is not used by any active boards, so let's remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reserve the 'normal' name for use by driver model, and rename the old
driver so that it is clear that it is for 'legacy' drivers only.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust the sandbox SPI driver to support driver model and move sandbox over
to driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Some files are using SPI functions but not explitly including the SPI
header file. Fix this, since driver model needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
U-Boot includes a SPI emulation driver already but it is not explicit, and
is hidden in the SPI flash code.
Conceptually with sandbox's SPI implementation we have a layer which
creates SPI bus transitions and a layer which interprets them, currently
only for SPI flash. The latter is actually an emulation, and it should be
possible to add more than one emulation - not just SPI flash.
Add a SPI emulation uclass so that other emulations can be plugged in to
support different types of emulated devices on difference buses/chip
selects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a uclass which provides access to SPI buses and includes operations
required by SPI.
For a time driver model will need to co-exist with the legacy SPI interface
so some parts of the header file are changed depending on which is in use.
The exports are adjusted also since some functions are not available with
driver model.
Boards must define CONFIG_DM_SPI to use driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
(Discussed some follow-up comments which will address in future add-ons)
Buses sometimes want to pass data to their children when they are probed.
For example, a SPI bus may want to tell the slave device about the chip
select it is connected to.
Add a new function to permit the parent data to be supplied to the child.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses need to iterate through their children in some situations. Add a few
functions to make this easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
The defines at the top of the GPIO driver use single-character names for
parameters which are not very descriptive.
Improve these to use descriptive parameter names.
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
if (strncmp(name, entry->name, len))
continue;
/* Full match */
if (len == strlen(entry->name))
return entry;
is equivalent to:
if (!strcmp(name, entry->name))
return entry;
The latter is simpler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The function uclass_add() checks uc_drv->ops as follows:
if (uc_drv->ops) {
dm_warn("No ops for uclass id %d\n", id);
return -EINVAL;
}
It seems odd because it warns "No ops" when uc_drv->ops has
non-NULL pointer. (Looks opposite.)
Anyway, most of UCLASS_DRIVER entries have no .ops member.
This check makes no sense.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Freescale's SEC block has built-in Blob Protocol which provides
a method for protecting user-defined data across system power
cycles. SEC block protects data in a data structure called a Blob,
which provides both confidentiality and integrity protection.
Encapsulating data as a blob
Each time that the Blob Protocol is used to protect data, a
different randomly generated key is used to encrypt the data.
This random key is itself encrypted using a key which is derived
from SoC's non volatile secret key and a 16 bit Key identifier.
The resulting encrypted key along with encrypted data is called a blob.
The non volatile secure key is available for use only during secure boot.
During decapsulation, the reverse process is performed to get back
the original data.
Commands added
--------------
blob enc - encapsulating data as a cryptgraphic blob
blob dec - decapsulating cryptgraphic blob to get the data
Commands Syntax
---------------
blob enc src dst len km
Encapsulate and create blob of data $len bytes long
at address $src and store the result at address $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
blob dec src dst len km
Decapsulate the blob of data at address $src and
store result of $len byte at addr $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The ipu display insists on having a lower_margin smaller
then 2. If this is not the case it will attempt to force
it and adjust the pixclk accordingly. This multiplies pixclk
in Hz with the width and height, since this is typically
a * 10^7 * b * 10^2 * c * 10^2 this will overflow the
uint_32 and make things even worse. Since this is a
bootloader and the adjustment is neglectible, just force
it to two and warn about it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)
This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: Roger Quadros <rogerq@ti.com>
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported. It is necessary to detect some
types of ONFi-compliant devices. Without it, the error message
"unsupported command received 0x5" is shown.
Let's support this command on the Denali NAND controller driver.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.
Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.
In addition, unnecessary clear_interrupts() should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards
cannot due to a hardware design decision. Select the correct driver to use
in each case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Unfortunately on Pit the AP has no direct access to the tps65090 but must
talk through the EC (over SPI) to the EC's I2C bus.
When driver model supports PMICs this will be relatively easy. In the
meantime the best approach is to duplicate the driver. It will be refactored
once driver model support is expanded.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.
Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This bit allows the MUSB controller to negotiate for high-speed mode when
the device is reset by the hub. If unset, Babble errors occur with
high-speed mass storage devices right after the first packet. This condition
is not caught by the interrupt handles in U-Boot, so no recovery is done,
and the USB communication is stuck.
To fix this, set the bit unconditionally, not only for
CONFIG_USB_GADGET_DUALSPEED but also for host-only modes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
Make the SoCFPGA MMC stub pick clock via the clock manager
frequency accessors instead of hard-coding the frequency.
Also fix calloc() misuse.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add a few new variables to make the cache handling less cryptic.
Add a variable for DMA and DATA descriptor start and end, so the
correctness of the code is easier to inspect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Fix remaining cache alignment issues in the DWC Ethernet driver.
Please note that the cache handling in the driver is making the
code hideous and thus the next patch cleans that up. In order to
make this change reviewable though, the cleanup is split from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
The dw_mmc driver was responding to errors with debug(). Change that
to prinf()/puts() respectively so that any errors are immediately
obvious. Also adjust english in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Chin Liang See <clsee@altera.com>
Add a table of FPGA family with matching functions associated with
it and make all the code just look up the family in that table and
call the associated function instead of the horrible switch voodoo
which was duplicated all over the place.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Make the function return either 0 or -EINVAL, that is, normal
expected error codes and success codes instead of true/false
nonsense.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Move the function to the top of the file to avoid forward declaration.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
