Commit graph

1695 commits

Author SHA1 Message Date
Simon Glass
874dde8016 dm: usb: exynos: Use driver model for USB
Convert Exynos boards over to use driver model for USB. This does not remove
any unnecessary code so far.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-04-18 11:11:29 -06:00
Kishon Vijay Abraham I
4564faeafb ti: dwc3: Enable clocks in enable_basic_clocks() in hw_data.c
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.

Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-16 15:08:36 -04:00
Tom Rini
20913018fb Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-04-16 12:51:23 -04:00
Valentine Barshak
9ba379ade7 ARM: cpu: Add ARMv7 barrier operations support
This enables ARMv7 barrier operations support when
march=armv7-a is enabled.

Using CP15 barriers causes U-Boot bootm command crash when
transferring control to the loaded image on Renesas R8A7794 Cortex A7 CPU.
Using ARMv7 barrier operations instead of the deprecated CP15 barriers
helps to avoid these issues.

Signed-off-by: Valentine Barshak <valentine.barshak+renesas@cogentembedded.com>
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2015-04-16 13:53:26 +02:00
Hans de Goede
a0e2b1b865 sunxi: usbc: Wait for vbus to fall after disabling it
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.

Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15 16:17:17 +02:00
Hans de Goede
046ea8b390 sunxi: usbc: Initialize vusb value on request_resources
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.

For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
487b3277d4 sunxi: GPIO pin mux hardware-feature-specific function index defines
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
ebd468b2d2 sunxi: common VBUS detection logic in usbc
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.

In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
5eaacb4340 sunxi: usb: Drop AXP-sepcific VBUS detection and drive logic
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Kishon Vijay Abraham I
fc2f15d2f7 ARM: AM43xx: Enable clocks for USB OTGSS and USB PHY
Enabled clocks for dwc3 controller and USB PHY present in AM43xx.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Kishon Vijay Abraham I
d3cfcb3e2c ARM: DRA7: Enable clocks for USB OTGSS and USB PHY
Enabled clocks for dwc3 controller and USB PHY present in DRA7.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Tom Rini
1d2f74690c Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-04-13 10:52:46 -04:00
Stefan Roese
4adb46a314 arm: armada-xp: Fix SPL for AXP by using save_boot_params_ret
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced
a different method to return from save_boot_params(). The SPL support
for AXP has been pulled and changing to this new method is now
required for SPL to work correctly.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-04-11 11:49:00 +02:00
Albert ARIBAUD
b491d9757d Merge branch 'u-boot/master' 2015-04-10 14:22:23 +02:00
Andrej Rosano
3bf801a217 ARM: mx5: add support for USB armory board
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.

http://inversepath.com/usbarmory

Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-09 09:14:12 +02:00
Andrej Rosano
424ee3d157 ARM: mx5: move to a standard arch/board approach
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
commit: 89ebc82137

Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-09 09:13:54 +02:00
Tom Rini
e049b772ae am33xx/ddr.c: Fix regression on DDR2 platforms
Back in fc46bae a "clean up" was introduced that intended to reconcile
some of the AM335x codepaths based on how AM43xx operates.
Unfortunately this introduced a regression on the DDR2 platforms.  This
was un-noticed on DDR3 (everything except for Beaglebone White) as we
had already populated sdram_config correctly in sequence.  This change
brings us back to the older behavior and is fine on all platforms.

Tested on Beaglebone White, Beaglebone Black and AM335x GP EVM

Reported-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-07 08:41:10 -04:00
Ajay Kumar
6102560891 Exynos5: Fix rpll_sdiv to support both peach-pit and peach-pi panels
The existing setting for rpll_sdiv generates 70.5Mhz RPLL
video clock to drive 1366x768 panel on peach_pit.

This clock rate is not sufficient to drive 1920x1080 panel on peach-pi.
So, we adjust rpll_sdiv to 3 so that it generates 141Mhz pixel clock
which can drive peach-pi LCD.

This change doesn't break peach-pit LCD since 141/2=70.5Mhz, i.e FIMD
divider at IP level will get set to 1(the required divider setting
will be calculated and set by exynos_fimd_set_clock()) and hence
peach-pit LCD still works fine.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06 14:34:40 +09:00
Ajay Kumar
70b4fb660d arm: exynos: add display clocks for Exynos5800
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5800 needed by
exynos video driver.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06 14:34:40 +09:00
Guillaume GARDET
0467faf555 Exynos: Clock: Fix exynos5_get_periph_rate for I2C.
Commit 2e82e92526 'Exynos: Clock: Cleanup
soc_get_periph_rate' introduced a bug in I2C config. This patch makes cros_ec
keyboard working again on Samsung Chromebook (snow).

Changes in V2: reorder lines as requested by Joonyoung Shim.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Simon Glass <sjg@chroimum.org>
Tested-by: Simon Glass <sjg@chroimum.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-06 14:05:45 +09:00
Tom Rini
9da7e3daf3 Merge branch 'master' of git://git.denx.de/u-boot-imx 2015-03-31 11:45:36 -04:00
Iain Paton
e71b422bd7 sunxi: use CONFIG_SYS_CLK_FREQ to set cpu clock
make the CPU clock selectable via Kconfig

this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot

Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
 arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 13:36:03 +02:00
Iain Paton
7a140117ef sunxi: sun4i: improve cpu clock selection method
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.

reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 13:08:39 +02:00
Hans de Goede
246e3b8787 sunxi: musb: Fix some lo speed devices not working with musb host
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.

The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.

Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-29 12:58:59 +02:00
Masahiro Yamada
ddf6bd4876 ARM: bcm283x: merge BCM2835/BCM2836 directories into mach-bcm283x
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough.  One of the biggest differences is the ARM
processor.  It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2015-03-28 09:03:09 -04:00
Masahiro Yamada
326a682358 malloc_f: enable SYS_MALLOC_F by default if DM is on
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory.  Devices are scanned twice, before/after
relocation.  CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation.  As it is board-independent, handle it
globally.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
2015-03-28 09:03:09 -04:00
Masahiro Yamada
91405b7fa9 malloc_f: remove redundant defalut values of CONFIG_SYS_MALLOC_F_LEN
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400.  Each defconfig or Kconfig need not repeat the same value.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
2015-03-28 09:03:08 -04:00
Masahiro Yamada
79d75d7527 ARM: move -march=* and -mtune= options to arch/arm/Makefile
My main motivations for this commit are:

[1] Follow the arch/arm/Makefile style of Linux Kernel

[2] Maintain compiler options systematically
  Currently, we give -march=* and -mtune=* options inconsistently:
  Only some of the CPUs pass -march=* and -mtune=* options.
  By collecting such options into the single place arch/arm/Makefile
  we can tell which options are missing at a glance.

[3] Prepare for deprecating arch/*/cpu/*/config.mk

Note:
  This commit just moves the compiler options so as not to change
  the behavior at all.  It does not care about the correctness of
  the given options.  Fox example, "-march=armv5te" might be better
  than "-march=armv4" for ARM946EJS, but it is beyond the scope this
  commit.  Also, filling the missing -march=* and -tune=* is left
  to follow-up patches.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2015-03-27 16:55:22 +01:00
Rob Herring
7682a99826 remove unnecessary version.h includes
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
2015-03-24 10:50:50 -04:00
Boris BREZILLON
058d231687 board/seco: Add mx6q-uq7 basic board support
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2015-03-23 13:19:18 +01:00
Boris BREZILLON
89ebc82137 ARM: mx6: move to a standard arch/board approach
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.

Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.

Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2015-03-23 13:18:01 +01:00
Tom Rini
a538ae997a Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-03-18 07:07:43 -04:00
Nishanth Menon
cdef0b3f3a ARM: OMAP3: rx51: Enable workaround for ARM errata 454179, 430973, 621766
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.

While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:33 -04:00
Nishanth Menon
c6f90e1418 ARM: OMAP3: Enable workaround for ARM errata 454179, 430973, 621766
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:24 -04:00
Nishanth Menon
fc7368ec85 ARM: OMAP5 / DRA7: Setup L2 Aux Control Register with recommended configuration
Update to existing recommendation for L2ACTLR configuration to prevent
system instability and optimize performance.

These apply to both OMAP5 and DRA7.

Reported-by: Vivek Chengalvala <vchengalvala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:13 -04:00
Praveen Rao
5f603761c3 ARM: DRA7 / OMAP5: Add workaround for ARM errata 798870
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."

An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.

Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:01 -04:00
Nishanth Menon
49ec949091 ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1
omap_smc1 is now generic enough to remove duplicate
omap3_gp_romcode_call logic that omap3 introduced.

As part of this change, move to using the generic lowlevel_init.S for
omap3 as well.

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:00 -04:00
Nishanth Menon
6d8abe6a8a ARM: OMAP: Change set_pl310_ctrl_reg to be generic
set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup
PL310 control register, however, that is something that is generic
enough to be used for OMAP5 generation of processors as well. The only
difference being the service being invoked for the function.

So, convert the service to a macro and use a generic name (same as
that used in Linux for some consistency). While at that, also add a
data barrier which is necessary as per recommendation.

While at this, smc #0 is maintained as handcoded assembly thanks to
various gcc version eccentricities, discussion thread:
http://marc.info/?t=142542166800001&r=1&w=2

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:55 -04:00
Nishanth Menon
9b4d65f918 ARM: Introduce erratum workaround for 621766
621766: Under a specific set of conditions, executing a sequence of
	NEON or vfp load instructions can cause processor deadlock
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set L1NEON to 1

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:53 -04:00
Nishanth Menon
5902f4ce0f ARM: Introduce erratum workaround for 430973
430973: Stale prediction on replaced inter working branch causes
	Cortex-A8 to execute in the wrong ARM/Thumb state
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE to 1

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:52 -04:00
Nishanth Menon
b45c48a7c3 ARM: Introduce erratum workaround for 454179
454179: Stale prediction may inhibit target address misprediction on
	next predicted taken branch
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around:  Set IBE and disable branch size mispredict to 1

Also provide a hook for SoC specific handling to take place if needed.

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:48 -04:00
Nishanth Menon
c616a0df29 ARM: Introduce erratum workaround for 798870
Add workaround for Cortex-A15 ARM erratum 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."

Implementations for SoC families such as Exynos, OMAP5/DRA7 etc
will be widely different.

Every SoC has slightly different manner of setting up access to L2ACLR
and similar registers since the Secure Monitor handling of Secure
Monitor Call(smc) is diverse. Hence an weak function is introduced
which may be overriden to implement SoC specific accessor implementation.

Based on ARM errata Document revision 18.0 (22 Nov 2013)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:29 -04:00
Dirk Behme
9d16c52f62 mx6: soc: Switch to cold reset
Disable the warm reset and enable the cold reset for a more reliable
restart ('reset'). This is taken from the Linux kernel, see imx_src_init()
in arch/arm/mach-imx/src.c.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
2015-03-13 13:29:42 +01:00
Peng Fan
0c1842a01f imx:mx6 remove duplicated includes
There is no need to include asm/bootm.h twice, so remove one.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-03-13 13:28:04 +01:00
Tom Rini
b79dadf846 Merge branch 'master' of git://git.denx.de/u-boot-tegra
Conflicts:
	README

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-10 19:09:18 -04:00
Tom Rini
dd09f7e73c ARM: PSCI: Rework the DT handler slightly
The way the PSCI DT update happens currently means we pull in
<asm/armv7.h> everywhere, including on ARMv8 and that in turn brings in
<asm/io.h> for some non-PSCI related things that header needs to deal
with.

To fix this, we rework the hook slightly.  A good portion of
arch/arm/cpu/armv7/virt-dt.c is common looking and I hope that when PSCI
is needed on ARMv8 we can re-use this by and large.  So rename the
current hook to psci_update_dt(), move the prototype to <asm/psci.h> and
add an #ifdef that will make re-use later easier.

Reported-by: York Sun <yorksun@freescale.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: York Sun <yorksun@freescale.com>
2015-03-09 11:13:29 -04:00
Ash Charles
b050898efa omap: gpmc: 'nandecc sw' can use HAM1 or BCH8
The 'nandecc sw' command selects a software-based error correction
algorithm.  By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm.  Allow a user to be specific e.g.
 # nandecc sw <hamming|bch8>
where 'hamming' is still the default.

Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
      to a hardware-based ECC scheme---a little strange when the user
      has requested 'sw' ECC.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
2015-03-05 20:49:43 -05:00
Albert ARIBAUD \(3ADEV\)
d275c40c69 omap3: add support for QUIPOS Cairo board.
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-03-05 20:13:21 -05:00
Stefano Babic
9b5b60a05c Merge branch 'master' of git://git.denx.de/u-boot 2015-03-05 16:05:10 +01:00
Tom Rini
02ebe6f702 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-03-05 07:22:18 -05:00
Simon Glass
7ae8350f67 ti: armv7: Move SPL SDRAM init to the right place, drop unused CONFIG_SPL_STACK
Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f().  Adjust the
code paths in these cases to be correct.  In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment).  In these cases switch to CONFIG_SPL_STACK_R.  In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM.  In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-03-04 14:55:04 -05:00
Simon Glass
24a6bc010e arm: Reduce the scope of lowlevel_init()
This function has grown into something of a monster. Some boards are setting
up a console and DRAM here in SPL. This requires global_data which should be
set up in one place (crt0.S).

There is no need for SPL to use s_init() for anything since board_init_f()
is called immediately afterwards.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-03-04 14:55:04 -05:00
Stefano Babic
b9cb64825b Merge branch 'master' of git://git.denx.de/u-boot 2015-03-02 09:42:53 +01:00
Tom Rini
6fa361903c Merge branch 'master' of git://git.denx.de/u-boot-samsung 2015-03-01 22:05:54 -05:00
Tom Rini
1da7ce4155 Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2015-03-01 21:07:53 -05:00
Tom Rini
fc83410095 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2015-03-01 21:06:47 -05:00
Peng Fan
02251eefc9 ARM: HYP/non-sec: relocation before enable secondary cores
If CONFIG_ARMV7_PSCI is not defined and CONFIG_ARMV7_SECURE_BASE is defined,
smp_kicl_all_cpus may enable secondary cores and runs into secure_ram_addr(
_smp_pen), before code is relocated to secure ram.
So need relocation to secure ram before enable secondary cores.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-01 16:33:21 +01:00
Masahiro Yamada
4c42557021 ARM: UniPhier: move SoC sources to mach-uniphier
Move
arch/arm/cpu/armv7/uniphier/* -> arch/arm/mach-uniphier/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01 00:01:56 +09:00
Doug Anderson
306f527eff Exynos: Fix L2 cache timings on Exynos5420 and Exynos5800
It was found that the L2 cache timings that we had before could cause
freezes and hangs.  We should make things more robust with better
timings.  Currently the production ChromeOS kernel applies these
timings, but it's nice to fixup firmware too (and upstream probably
won't take our kernel hacks).

This also provides a big cleanup of the L2 cache init code avoiding
some duplication.  The way things used to work:
* low_power_start() was installed by the SPL (both at boot and resume
  time) and left resident in iRAM for the kernel to use when bringing
  up additional CPUs.  It used configure_l2_ctlr() and
  configure_l2_actlr() when it detected it was on an A15.  This was
  needed (despite the L2 cache registers being shared among all A15s)
  because we might have been the first man in after the whole A15
  cluster was shutdown.
* secondary_cores_configure() was called on at boot time and at resume
  time.  Strangely this called configure_l2_ctlr() but not
  configure_l2_actlr() which was almost certainly wrong.  Given that
  we'll call both (see next bullet) later in the boot process it
  didn't matter for normal boot, but I guess this is how L2 cache
  settings got set on 5420/5800 (but not 5250?) at resume time.
* exynos5_set_l2cache_params() was called as part of cache enablement.
  This should happen at boot time (normally in the SPL except for USB
  boot where it happens in main U-Boot).

Note that the old code wasn't setting ECC/parity in the cache
enablement code but we happened to get it anyway because we'd call
secondary_cores_configure() at boot time.  For resume time we'd get it
anyway when the 2nd A15 core came up.

Let's make this a whole lot simpler.  Now we always set these
parameters in the same place for all boots and use the same code for
setting up secondary CPUs.

Intended net effects of this change (other than cleanup):
* Timings go from before:
    data: 0 cycle setup, 3 cycles (0x2) latency
    tag:  0 cycle setup, 3 cycles (0x2) latency
  after:
    data: 1 cycle setup, 4 cycles (0x3) latency
    tag:  1 cycle setup, 4 cycles (0x3) latency
* L2ACTLR is properly initted on 5420/5800 in all cases.

One note is that we're still relying on luck to keep low_power_start()
working.  The compiler is being nice and not storing anything on the
stack.

Another note is that on its own this patch won't help to fix cache
settings in an RW U-Boot update where we still have the RO SPL.  The
plan for that is:
* Have RW U-Boot re-init the cache right before calling the kernel
  (after it has turned the L2 cache off).  This is why the functions
  are in a header file instead of lowlevel_init.c.

* Have the kernel save the L2 cache settings of the boot CPU and apply
  them to all other CPUs.  We get a little lucky here because the old
  code was using "|=" to modify the registers and all of the bits that
  it's setting are also present in the new settings (!).  That means
  that when the 2nd CPU in the A15 cluster comes up it doesn't
  actually mess up the settings of the 1st CPU in the A15 cluster.  An
  alternative option is to have the kernel write its own
  low_power_start() code.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
c8fd8e66cd Exynos542x: Make A7s boot with thumb-mode U-Boot on warm reset
On warm reset, all cores jump to the low_power_start function because iRAM
data is retained and because while executing iROM code all cores find
the jump flag 0x02020028 set. In low_power_start, cores check the reset
status and if true they clear the jump flag and jump back to 0x0.

The A7 cores do jump to 0x0 but consider following instructions as a Thumb
instructions which in turn makes them loop inside the iROM code instead of
jumping to power_down_core.

This issue is fixed by replacing the "mov pc" instruction with a "bx"
instruction which switches state along with the jump to make the execution
unit consider the branch target as an ARM instruction.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
cecf2db23b Exynos542x: Fix secondary core booting for thumb
When compiled SPL for Thumb secondary cores failed to boot
at the kernel boot up. Only one core came up out of 4.
This was happening because the code relocated to the
address 0x02073000 by the primary core was an ARM asm
code which was executed by the secondary cores as if it
was a thumb code.
This patch fixes the issue of secondary cores considering
relocated code as Thumb instructions and not ARM instructions
by jumping to the relocated with the help of "bx" ARM instruction.
"bx" instruction changes the 5th bit of CPSR which allows
execution unit to consider the following instructions as ARM
instructions.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
7e514eef02 Exynos542x: add L2 control register configuration
This patch does 3 things:
1. Enables ECC by setting 21st bit of L2CTLR.
2. Restore data and tag RAM latencies to 3 cycles because iROM sets
   0x3000400 L2CTLR value during switching.
3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR.
   We need to restore this here due to switching.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
f0f76b0a4c Exynos542x: cache: Disable clean/evict push to external
L2 Auxiliary Control Register provides configuration
and control options for the L2 memory system. Bit 3
of L2ACTLR stands for clean/evict push to external.
Setting bit 3 disables clean/evict which is what
this patch intends to do.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
67a0652c47 Exynos542x: Add workaround for exynos iROM errata
iROM logic provides undesired jump address for CPU2.
This patch adds a programmable susbstitute for a part of
iROM logic which wakes up cores and provides jump addresses.
This patch creates a logic to make all secondary cores jump
to a particular address which evades the possibility of CPU2
jumping to wrong address and create undesired results.

Logic of the workaround:

Step-1: iROM code checks value at address 0x2020028.
Step-2: If value is 0xc9cfcfcf, it jumps to the address (0x202000+CPUid*4),
	else, it continues executing normally.
Step-3: Primary core puts secondary cores in WFE and store 0xc9cfcfcf in
	0x2020028 and jump address (pointer to function low_power_start)
	in (0x202000+CPUid*4).
Step-4: When secondary cores recieve event signal they jump to this address
	and continue execution.

Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Akshay Saraswat
ac0d98cd55 Exynos542x: CPU: Power down all secondary cores
This patch adds code to shutdown secondary cores.
When U-boot comes up, all secondary cores appear powered on,
which is undesirable and causes side effects while
initializing these cores in kernel.

Secondary core power down happens in following steps:

Step-1: After Exynos power-on, primary core starts executing first.
Step-2: In iROM code every core has to check 2 flags i.e.
	addresses 0x02020028 & 0x02020004.
Step-3: Initially 0x02020028 is 0 for all cores and 0x02020004 has a
	jump address for primary core and 0 for all secondary cores.
Step-4: Therefore, primary core follows normal iROM execution and jumps
	to BL1 eventually, whereas all secondary cores enter WFE.
Step-5: When primary core comes into function secondary_cores_configure,
	it puts pointer to function power_down_core into 0x02020004
	and provides DSB and SEV for all cores so that they may come out
	of WFE and jump to power_down_core function.
Step-6: And ultimately because of power_down_core all
	secondary cores shut-down.

Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-28 18:03:46 +09:00
Tom Rini
1606b34aa5 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-02-25 18:14:18 -05:00
Vladimir Barinov
60c0467a94 arm: rmobile: Add Porter board support
Porter is an entry level development board based on R-Car M2 SoC (R8A7791)

This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, SD, USB Host

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25 14:17:49 +09:00
Nobuhiro Iwamatsu
acdfecbbb4 arm: rmobile: lager: Add support SDHI
Lager board has two SDHI port as SDHI0 and SDHI2.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25 13:13:49 +09:00
Nobuhiro Iwamatsu
25f9613fcf arm: rmobile: alt: Add support SDHI
Alt board has two SDHI port.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25 13:13:38 +09:00
Masahiro Yamada
d648964fc2 kconfig: remove unneeded dependency on !SPL_BUILD
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-24 17:06:27 -05:00
Masahiro Yamada
e02ee2548a kconfig: switch to single .config configuration
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL).  There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.

It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:

[1] It is impossible to share CONFIG options across the images.
  If you change the configuration of Main image, you often have to
  adjust some SPL configurations correspondingly.  Currently, we
  cannot handle the dependencies between them.  It means one of the
  biggest advantages of Kconfig is lost.

[2] It is too painful to change both ".config" and "spl/.config".
  Sunxi guys started to work around this problem by creating a new
  configuration target.  Commit cbdd9a9737 (sunxi: kconfig: Add
  %_felconfig rule to enable FEL build of sunxi platforms.) added
  "make *_felconfig" to enable CONFIG_SPL_FEL on both images.
  Changing the configuration of multiple images in one command is a
  generic demand.  The current implementation cannot propose any
  good solution about this.

[3] Kconfig files are getting ugly and difficult to understand.
  Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
  Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.

[4] The build system got more complicated than it should be.
  To adjust Linux-originated Kconfig to U-Boot, the helper script
  "scripts/multiconfig.sh" was introduced.  Writing a complicated
  text processor is a shell script sometimes caused problems.

Now I believe the "single .config" will serve us better.  With it,
all the problems above would go away.  Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much.  Anyway, this is what we do now in
scripts/Makefile.spl.

I admit my mistake with my apology and this commit switches to the
single .config configuration.

It is not so difficult to do that:

 - Remove unnecessary processings from scripts/multiconfig.sh
  This file will remain for a while to support the current defconfig
  format.  It will be removed after more cleanups are done.

 - Adjust some makefiles and Kconfigs

 - Add some entries to include/config_uncmd_spl.h and the new file
   scripts/Makefile.uncmd_spl.  Some CONFIG options that are not
   supported on SPL must be disabled because one .config is shared
   between SPL and U-Boot proper going forward.  I know this is not
   a beautiful solution and I think we can do better, but let's see
   how much we will have to describe them.

 - update doc/README.kconfig

More cleaning up patches will follow this.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-24 17:06:23 -05:00
Masahiro Yamada
6d4d05b1e9 ARM: UniPhier: set CONFIG_SYS_MALLOC_F to the global default value
It is true that malloc is necessary for Driver Model before
relocation, but there is no good reason to reserve the malloc
space more than enough.  The default value 0x400 works well.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-24 17:05:22 -05:00
chenhui zhao
9f076be713 arm: ls102xa: workaround for cache coherency problem
The RCPM FSM may not be reset after power-on, for example,
in the cases of cold boot and wakeup from deep sleep.
It causes cache coherency problem and may block deep sleep.
Therefore, reset them if they are not be reset.

Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:10:59 -08:00
Minghuan Lian
636ef95605 arm/ls102xa: create TLB to map PCIe region
LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins
0x48_00000000. In order to access PCIe device, we must create
TLB to map the 40bit physical address to 32bit virtual address.
This patch will enable MMU after DDR is available and creates MMU
table in DRAM to map all 4G space; then, re-use the reserved space
to map PCIe region. The following the mapping layout.

VA mapping:
    -------  <---- 0GB
   |       |
   |       |
   |-------| <---- 0x24000000
   |///////|  ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000
   |-------| <---- 0x300000000
   |       |
   |-------| <---- 0x34000000
   |///////|  ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000
   |-------| <---- 0x40000000
   |       |
   |-------| <---- 0x80000000 DDR0 space start
   |\\\\\\\|
   |\\\\\\\|  ===> 2GB VA map for 2GB DDR0 Memory space
   |\\\\\\\|
   -------  <---- 4GB DDR0 space end

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:10:31 -08:00
Stephen Warren
db75356f14 bcm2836 SoC support (used in Raspberry Pi 2 model B)
The bcm2835 and bcm2836 are essentially identical, except:
- The CPU is an ARM1176 v.s. a quad-core Cortex-A7.
- The physical address of many IO controllers has moved.

Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH),
update the existing bcm2835 code to handle the minor differences, and
plumb it into the ARMv7 CPU architecture.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21 08:27:48 -05:00
Masahiro Yamada
39a723452f ARM: keystone: move SoC sources to mach-keystone
Move
arch/arm/cpu/armv7/keystone/* -> arch/arm/mach-keystone/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2015-02-21 08:23:52 -05:00
Masahiro Yamada
72a8ff4b04 ARM: highbank: move SoC sources to mach-highbank
Move
arch/arm/cpu/armv7/highbank/* -> arch/arm/mach-highbank/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <robh@kernel.org>
2015-02-21 08:23:51 -05:00
Masahiro Yamada
09f455dca7 ARM: tegra: collect SoC sources into mach-tegra
This commit moves files as follows:

 arch/arm/cpu/arm720t/tegra20/*      -> arch/arm/mach-tegra/tegra20/*
 arch/arm/cpu/arm720t/tegra30/*      -> arch/arm/mach-tegra/tegra30/*
 arch/arm/cpu/arm720t/tegra114/*     -> arch/arm/mach-tegra/tegra114/*
 arch/arm/cpu/arm720t/tegra124*      -> arch/arm/mach-tegra/tegra124/*
 arch/arm/cpu/arm720t/tegra-common/* -> arch/arm/mach-tegra/*
 arch/arm/cpu/armv7/tegra20/*        -> arch/arm/mach-tegra/tegra20/*
 arch/arm/cpu/armv7/tegra30/*        -> arch/arm/mach-tegra/tegra30/*
 arch/arm/cpu/armv7/tegra114/*       -> arch/arm/mach-tegra/tegra114/*
 arch/arm/cpu/armv7/tegra124/*       -> arch/arm/mach-tegra/tegra124/*
 arch/arm/cpu/armv7/tegra-common/*   -> arch/arm/mach-tegra/*
 arch/arm/cpu/tegra20-common/*       -> arch/arm/mach-tegra/tegra20/*
 arch/arm/cpu/tegra30-common/*       -> arch/arm/mach-tegra/tegra30/*
 arch/arm/cpu/tegra114-common/*      -> arch/arm/mach-tegra/tegra114/*
 arch/arm/cpu/tegra124-common/*      -> arch/arm/mach-tegra/tegra124/*
 arch/arm/cpu/tegra-common/*         -> arch/arm/mach-tegra/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org> [ on nyan-big ]
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2015-02-21 08:23:51 -05:00
Masahiro Yamada
620118403e ARM: at91: collect SoC sources into mach-at91
This commit moves source files as follows:

  arch/arm/cpu/arm920t/at91/*   -> arch/arm/mach-at91/arm920t/*
  arch/arm/cpu/arm926ejs/at91/* -> arch/arm/mach-at91/arm926ejs/*
  arch/arm/cpu/armv7/at91/*     -> arch/arm/mach-at91/armv7/*
  arch/arm/cpu/at91-common/*    -> arch/arm/mach-at91/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
2015-02-21 08:23:51 -05:00
Tom Rini
a851604ca3 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-02-17 06:27:44 -05:00
Peng Fan
83dd1dd91c ARM: imx6 Add WDOG3 for i.MX6SX
There are three wdogs for i.MX 6SoloX. Add wdog3 support
in function imx_set_wdog_powerdown.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-17 10:42:53 +01:00
Peng Fan
1f516faa45 ARM: imx6: disable bandgap self-bias after boot
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
2015-02-17 10:42:53 +01:00
Siarhei Siamashka
840fe95c3b sunxi: Support the FEL boot mode in the regular u-boot build
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.

A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.

The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
 the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:23:52 +01:00
Simon Glass
942cb0b6a2 sunxi: Normalise FEL support
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.

This series is available at u-boot-dm, branch sunxi-working.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:15:09 +01:00
Simon Glass
e11c6c279d arm: Allow lr to be saved by board code
The link register value can be required on some boards (e.g. FEL mode on
sunxi) so use a branch instruction to jump to save_boot_params() instead
of a branch link.

This requires a branch back to save_boot_params_ret so adjust the users
to deal with this. For exynos just drop the function since it doesn't
do anything.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:14:54 +01:00
Hans de Goede
51637afe98 sunxi: dram: Un-inline dram helper functions
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-16 20:05:52 +01:00
Vitaly Andrianov
66c98a0c38 keystone2: ddr3: eliminate using global ddr3_size variable
KS2 ddr3 initialization uses ddr3_size global variable before u-boot
relocation. Even if the variable is not being used after relocation,
writing to it corrupts relocation table.

This patch removes the global ddr3_size variable and uses local one
instead.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2015-02-16 12:41:41 -05:00
Steve Kipisz
bba379d498 clock_am43xx:Set the MAC clock to /5 for OPP100
When EMAC is in the boot order, the boot ROM sets OPP50 and the
MAC clock is set to /2. SPL needs to change it to /5 for Ethernet
to generate the correct txclk. This patch sets it correctly.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
2015-02-16 12:41:40 -05:00
Lokesh Vutla
1860d10196 ARM: DRA7-evm: DDR3: Update leveling values
Update the software leveling parameters.
This fixes the random crash seen on DRA7-evm.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-02-16 12:41:40 -05:00
Lokesh Vutla
802bb57a58 ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register value
The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL
should be written with a value corresponding to 500us delay before
starting DDR initialization sequence, and configure proper
value at the end of sequence.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-02-16 12:41:40 -05:00
Angela Stegmaier
aa8ac43645 ARM: DRA72x: DDR3: Fix EMIF timings for 666MHz clock
DDR3 timing and latency paramenters were not configured
correctly for 666MHz. Fixing the timing and latency values
according to Data sheet.
This fixes the random crashes seen on DRA72-evm.

Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-02-16 12:41:40 -05:00
Tom Rini
eca99c0256 Merge git://git.denx.de/u-boot-samsung 2015-02-13 13:11:33 -05:00
Tom Rini
757566d156 Merge git://git.denx.de/u-boot-dm 2015-02-13 13:11:09 -05:00
Tom Rini
921ed4e840 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2015-02-13 13:10:25 -05:00
Akshay Saraswat
2e82e92526 Exynos: Clock: Cleanup soc_get_periph_rate
Since we have src, div and pre-div mask bits defined corresponding
to peripherals, calculation of clock specific to I2C appears
redundant and confusing. Using clk_bit_info struct we can write
calculations generic to all peripherals which makes code easy to
understand and free from peripheral specific exceptions.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
c5d32170bb Exynos: clock: change mask bits as per peripheral
We have assumed and kept mask bits for divider and pre-divider
as 0xf and 0xff, respectively. But these mask bits change from
one peripheral to another, and hence, need to be specified in
accordance with the peripherals.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
d95279685b Exynos5: Use clock_get_periph_rate generic API
Replacing SoC and peripheral specific function calls with generic
clock_get_periph_rate calls to get the peripheral clocks.
Also, removing dead code of peripheral and SoC specific function
implementations which was used earlier for fetching peripheral clocks.
This code is not being used anymore because of the introduction
of generic clock_get_periph_rate function.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
9deff10746 Exynos5: Fix exynos5_get_periph_rate calculations
exynos5_get_periph_rate function reads incorrect div for
SDMMC2 & 3. It also reads prediv and does division only for
SDMMC0 & 2 when actually various other peripherals need that.
Adding changes to fix these mistakes in periph rate calculation.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
ecdfb4e9d2 Exynos542x: Add and enable get_periph_rate support
We planned to fetch peripheral rate through one generic API per
peripheral. These generic peripheral functions are in turn
expected to fetch apt values from a function refactored as
per SoC versions. This patch adds support for fetching peripheral
rates for Exynos5420 and Exynos5800.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
325eb18c77 Exynos542x: Move exynos5420_get_pll_clk up and rename
Moving exynos5420_get_pll_clk function definition up in the
code to keep it together with rest of SoC_get_pll_clk functions.
This makes code more legible and also removes the need of
declaration when called before the position of definition in
code. Also, renaming exynos5420_get_pll_clk to
exynos542x_get_pll_clk because it is being used for both Exynos
5420 and 5800.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Akshay Saraswat
d606ded1db Exynos5: Fix compiler warnings due to clock_get_periph_rate
Apparently, members of clk_bit_info array do not map correctly
to the members of enum periph_id. This mapping got broken after
we changed periph_id(s) to reflect interrupt number instead of
their position in a sequence. This patch intends to fix above
mentioned issue.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:23:06 +09:00
Joonyoung Shim
483e49bfd7 EXYNOS5: Add function to enable exynos5420 usbdev phy ctrl
Exynos5420 has different registers with other exynos5 SoCs to control
usb device phy, so need separated function to enable exynos5420 usb
device phy.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:19:55 +09:00
Jaehoon Chung
a276172cf3 arm: exynos: fix the div value for set_mmc_clk
The most exynos used the  "Ratio + 1" as div value.
And value at register is "Ratio".
So if want to set exact value, it needs to subtract one.

Value at register ("Ratio") = div - 1

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-13 17:15:14 +09:00
Nobuhiro Iwamatsu
3eda55a32d arm: rmobile: r8a7794: Enable SMP mode of Auxiliary Control Register
r8a7794 uses ARM SoC of CA7 base. If we want to use dcache on CA7, we
need to enable SMP bit of Auxiliary Control Register.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-13 13:14:56 +09:00
Vladimir Barinov
3b7f0e109c arm: rmobile: Add SILK board support
SILK is an entry level development board based on R-Car E2 SoC (R8A7794)

This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, MMC, USB Host

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-13 13:14:56 +09:00
Simon Glass
b724bd7d63 dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to Kconfig
Move this option to Kconfig and update all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 15:17:28 -07:00
Simon Glass
001646c478 dm: omap3: Move driver model CONFIGs to Kconfig
Remove driver model CONFIGs from the board config headers and use Kconfig
instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 10:35:35 -07:00
Simon Glass
d7a4b2e42e dm: tegra: Move driver model CONFIGs to Kconfig
Remove driver model CONFIGs from the board config headers and use Kconfig
instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 10:35:34 -07:00
Simon Glass
aab7e80d5f dm: exynos: Move driver model CONFIGs to Kconfig
Remove driver model CONFIGs from the board config headers and use Kconfig
instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 10:35:34 -07:00
Tom Rini
c956662cc3 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-02-10 10:42:22 -05:00
Tom Rini
307367eaff Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-02-10 10:40:43 -05:00
Ye.Li
e8cdeefc22 imx: mx6: Fixed AIPS3 base address issue
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.

Signed-off-by: Ye.Li <B37916@freescale.com>
2015-02-10 12:48:49 +01:00
Bo Shen
569bbd3ceb ARM: atmel: sama5d4: add interrupt redirect function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07 23:42:50 +01:00
Bo Shen
09f5c9745b ARM: atmel: sama5d4: add bus matrix init function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07 23:42:49 +01:00
Bo Shen
05084443f0 ARM: atmel: clock: make it possible to configure HMX32
Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-02-07 23:42:40 +01:00
Tom Rini
5c123f5fbf Merge git://git.denx.de/u-boot-marvell 2015-02-06 12:02:59 -05:00
Stefan Roese
b0f80b913f arm: armada-xp: Add SPL support used to include the DDR training code
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
2015-02-06 17:24:56 +01:00
Masahiro Yamada
4e79908044 ARM: UniPhier: leave the last element of boot_device_table empty
Checking if the pointer is NULL would be easier to know the tail
of the boot_device_table[] array.
For clarification, add the /* sentinel */ comment.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
4431684910 ARM: UniPhier: refactor pinmon command
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array.  Its type should be "int" rather
than "u32".

Use only the iterator "i" for the loop in do_pinmon().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
ee470645d1 ARM: UniPhier: enable I2C input pins for PH1-sLD8
To use I2C controllers on PH1-sLD8, the bit 10 (SCL0/SDA0)
and bit 11 (SCL1/SDA1) of IECTRL register must be set.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
6c45ef4b94 ARM: UniPhier: do not compile unnecessary objects
It is true that unused functions are removed from the ELF image
by the compiler's garbage collection but relying on it too much
does not look nice.
Currently, the build is taking more than it should.

Refactor the makefiles to compile only files that are really needed.
CONFIG_SOC_INIT and CONFIG_DRAM_INIT are no longer needed by the
optimization.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
dc4057eb81 ARM: UniPhier: remove unused checkboard() functions
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), checkboard() is invoked only when
show_board_info() fails to get the model name from Device Tree.
It never happens because UniPhier SoCs now only work with
CONFIG_OF_CONTROL and all the root nodes of UniPhier device trees
have the "model" property.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
08fda258ee ARM: UniPhier: revive support card info
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), the support card information has not been
displayed because check_support_card() is invoked only when
show_board_info() fails to get the model name from Device Tree.

This commit adds misc_init_f() function to call check_support_card()
from there.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
35adfc4d25 ARM: UniPhier: move SPL init functions to spl_board_init()
Now init functions called from board_postclk_init() and dram_init()
are only necessary for SPL.
Move them to spl_board_init() for clean-up.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:03 +09:00
Masahiro Yamada
84ccd791af ARM: UniPhier: move pin_init() to board_early_init_f()
Currently, I/O pin settings are not necessary for SPL.
The board_early_init_f() seems a suitable place to call pin_init().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-07 00:15:02 +09:00
Tom Rini
37ffffb98d Merge branch 'master' of git://git.denx.de/u-boot-ti 2015-02-02 12:37:34 -05:00
Tom Rini
be8ddad9c8 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2015-02-02 10:11:44 -05:00
Hans de Goede
37d46dd3c4 sunxi: rsb: Move rsb_set_device_mode() call to rsb_init()
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
d35488c735 sunxi: rsb: Add sun9i (A80 support)
Add support for the A80 to the rsb code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Tom Rini
8e3da9dd11 Merge branch 'master' of git://git.denx.de/u-boot-dm 2015-01-30 09:24:42 -05:00
Peng Fan
0f274f5376 ARM: armv7 fix spelling of SCTRL
SCTLR is the abbreviation of System Control Register, so we should
use SCTLR but not SCTRL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-30 09:19:17 -05:00
Przemyslaw Marczak
fda0e27bfd exynos5: pinmux: check flag for i2c config
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:10:00 -07:00
Albert ARIBAUD \(3ADEV\)
03843da5d5 omap3: make SDRC SHARING setting configurable
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-01-29 12:00:50 -05:00
Albert ARIBAUD \(3ADEV\)
168f594765 omap3: enable GP9 timer and UART2
These are needed for the upcoming Cairo board support.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-01-29 12:00:50 -05:00
Lubomir Popov
b558af8128 ARM: OMAP5: DRA7xx: Add support for power rail grouping
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.

This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.

The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2015-01-29 12:00:49 -05:00
Tom Rini
aed03faa06 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-01-26 06:42:40 -05:00
Tom Rini
306df2c824 Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze 2015-01-26 06:42:15 -05:00
Michal Simek
63e3cea515 ARM: zynq: List nand, qspi and jtag boot modes
Use full boot mode list in SPL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Siva Durga Prasad Paladugu
f60c6fbbc6 ARM: zynq: slcr: Dont modify the reserved bits
Set only the 0-3 bits of the FPGA_RST_CTRL register
as other bits should not be set to 1.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
3ad87ca182 ARM: zynq: ddrc: Setup half of memory only for ECC case
Setup half of memory from ram_size for ECC case.
All the time the same board can be configured
with or without ECC. Based on ECC case detection
use half of memory with the same configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
555c7c066f ARM: zynq: Remove empty line
Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
c08cfc2d2c ARM: zynq: Enable the Neon instructions
Added the lowlevel_init to enable the Neon instructions.

Initially the u-boot was causing undefined instruction
exception if loaded through tcl, and working fine if loaded
through FSBL. The exception was causing in convertion formula
of given time to ticks. It was because, the Neon instructions
were disabled and hence causing the undefined exception. In
FSBL case, the FSBL was enabling the Neon instructions. Hence,
added the lowlevel_init to enable the Neon instructions.

Also enable neon instructions for non-xilinx toolchain.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:31 +01:00
tang yuantian
41ba57d0c7 fsl/ls1021qds: Add deep sleep support
Add deep sleep support on Freescale LS1021QDS platform.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-24 09:12:32 -06:00
Alison Wang
33d2e46591 ls102xa: fdt: Disable QSPI and DSPI in NOR/NAND/SD boot
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:14 -06:00
tang yuantian
5699274373 ARM: HYP/non-sec: Make variable gic_dist_addr as a local one
Defining variable gic_dist_addr as a globe one prevents some
functions, which use it, from being used before relocation
which is the case in the deep sleep resume process on Freescale
SoC platforms.
Besides, we can always get the GIC base address by calling
get_gicd_base_address() without referring gic_dist_addr.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:14 -06:00
Ruchika Gupta
0181937fa3 crypto/fsl: Add fixup for crypto node
Era property is added in the crypto node in device tree.
Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to
drivers/sec/sec.c so that it can be used across arm and
powerpc platforms having crypto node.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Fix commit message indentation]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:14 -06:00
Tom Rini
3b95288a2a Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-01-23 10:22:29 -05:00
Masahiro Yamada
ee94ee3464 ARM: UniPhier: remove non-sense inline directives
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-01-23 00:51:44 +09:00
Masahiro Yamada
ec79c79824 ARM: UniPhier: add static to local functions
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-01-23 00:51:21 +09:00
Masahiro Yamada
448437496b ARM: UniPhier: fix IECTRL set code for PH1-Pro4
For PH1-Pro4, the bit 6 of the IECTRL must be set.  It is the only
available bit in this register.  There is no effect of the write
access to the other bits.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-01-23 00:50:57 +09:00