This function cannot return true if PCI is not enabled, since no PCI
devices will have been bound. Add a check for this to reduce code size
where it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The spl_phase() function indicates whether U-Boot is in SPL and before
or after relocation. But sometimes it is useful to check for SPL with
zero code-size impact. Since spl_phase() checks the global_data flags,
it does add a few bytes.
Add a new spl_in_proper() function to check if U-Boot proper is
running, regardless of the relocation status.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses ARRAY_SIZE() but does not include the header file which declares
it. Fix this, so that command.h can be included without common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Typically the bloblist is set up after the devicetree is present. This
makes sense because bloblist may use malloc() to allocate the space it
needs.
However sometimes the devicetree itself may be present in the bloblist.
In that case it is at a known location in memory so we can init the
bloblist very early, before devicetree.
Add a flag to indicate whether the bloblist has been inited. Add a
function to init it only if needed. Use that in the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this down by 4KB so that it is large enough to hold the devicetree.
Also fix up the devicetree address in the documetation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not read this unless requested. Make it conditional on the
option being provided.
Add some debugging to show the state being written.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently relies on sandbox attempting to read a state file. At
present it always does, even when there is no state file, in which case it
fails, but still inits the EC.
That is a bug, so update this driver to set the current image always, even
if no state is read.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should not happen in the argument-parsing function. Move it to the
main program.
Add some debugging for reading/writing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few simple tests for getting the root node, since this is handled
as a special case in the implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for writing a single 64-bit value into a property.
Repurpose the existing tests to handle this case too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to write a boolean property. This involves deleting it if
the value is false.
Add a new ofnode_has_property() as well. Add a comment about the behaviour
of of_read_property() when the property value is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to flatten a devicetree into binary form. For livetree this
involves generating the devicetree using fdt_property() and other calls.
For flattree it simply involves providing the buffer containing the tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to copy a node to another place under a new name. This is
useful at least for testing, since copying a test node with existing
properties is easier than writing the code to generate it all afresh.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add comments to the functions where the test name does not indicate what
is being tested. Rename functions in a few cases, so that a search for the
function will also file its test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need the UT_TESTF_SCAN_FDT flag set for these tests to run with flat
tree. In some cases it is missing, so add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bloblist should not be finalised until the image is fully set up.
This allows any final handoff information to be included in the bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than open-coding the property names, use the existing constants
provided for this purpose. This better aligns the simple-FIT code with
the full FIT implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some reason this code was put in the main spl.c file. Move it out
to the FIT implementation where it belongs.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions called spl_load_fit_image(), one in spl.c and one in
spl_fit.c
Rename the second one, to indicate that it relates to simple FIT parsing,
rather than the full version.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature has some helpers in its header file so that its functions
resolve to nothing when the feature is disabled. Add a few more and use
these to simplify the code.
With this there are no more #ifdefs in board_init_r()
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the useful help to Kconfig.
Drop mention of CONFIG_SYS_MALLOC_SIMPLE since it doesn't exist.
Correct a 'CONFIGSYS_MALLOC_F_LEN' typo
Signed-off-by: Simon Glass <sjg@chromium.org>
Use CONFIG_SYS_MALLOC_F instead to of CONFIG_SYS_MALLOC_F_LEN to
determine whether pre-relocation malloc() is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Enable CONFIG_TPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_TPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_SPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
For U-Boot proper we have CONFIG_SYS_MALLOC_F which indicates that a
malloc() pool is available before relocation.
For SPL we only have CONFIG_SPL_SYS_MALLOC_F_LEN which indicates the
size of the pool.
In various places we use CONFIG_SPL_SYS_MALLOC_F_LEN == 0 to indicate
that there is no pool.
This differing approach is confusing. Add a new CONFIG_SPL_SYS_MALLOC_F
symbol for SPL (and similarly for TPL and VPL). Tidy up the Kconfig
help for clarity.
For now these symbols are not used. That is cleaned up in the following
patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols do not (yet) exist, so drop the usage of them in the
serial Kconfig file. It has no effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is pretty ugly, with many #ifdefs
There are quite a lot of IH_OS_U_BOOT values so the compiler struggles
to create a jump table here. Also, most of the options are normally
disabled.
Change it to an else...if construct instead. Add an accessor for the
spl_image field behind an #ifdef to avoid needing #ifdef in the C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
It doesn't make sense to have some boards do this differently. Drop the
condition in the hope that the maintainers can figure out any run-time
problems.
This has been tested on qemu-ppce500
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit d93036b47f35 ("arm64: dts: ti: k3-j721e-mcu_wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which eventually calls
dm_timer_init() to grab the tick-timer, which is mcu_timer0. Since we
need to set up the clocks before using the timer, move clk_k3 driver
probe before k3_sysfw_loader to ensure we have all necessary clocks set
up before.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
U-Boot uses mcu_timer0 as the tick-timer, so add it to device list.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
