Commit graph

7 commits

Author SHA1 Message Date
Tom Rini
1a77da4b33 Convert CONFIG_SYS_HZ to Kconfig
This converts the following to Kconfig:
	CONFIG_SYS_HZ

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-05 11:23:29 -04:00
Tom Rini
7cfbba36e9 Convert CONFIG_SYS_MALLOC_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31 17:47:49 -04:00
Tom Rini
72d81360aa global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR
- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
  CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
  noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:46:37 -04:00
Tom Rini
7d08077334 Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MMC_ENV_DEV
   CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-08 11:03:52 -04:00
Ashok Reddy Soma
702de89cc6 treewide: mem: Move mtest related defines to Kconfig
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 12:02:56 -04:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Shawn Guo
6802d7951c Add i.MX7D based Meerkat96 board support
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.

https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/

The initial supported/tested devices include:
 - Debug serial
 - SD
 - USB Host (with Ethernet)

With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-13 22:49:11 +02:00