This patch checks fpga config completion when a bitstream is loaded
into PL.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Correct the PL bitstream loading sequence for zynqaes command by
clearing the loaded PL bitstream before loading the new encrypted
bitstream using the zynq aes command. This was done by setting
the PROG_B same as in case of fpgaload commands.
This patch fixes the issue of loading the encrypted PL bitstream
onto the PL in which a bitstream has already been loaded
successfully.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to panic all the time when pmufw config object loading
failed. The patch improves function logic to report permission deny case
and also panic only for SPL case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
alt_ref_clk is applicable only for PS extended version.
For PS base version there is no separate alt_ref_clk.
It is tied with ref_clk, so remove it from driver.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason not to let U-Boot to update memory node by default. In
past this was disabled by purpose to be able to test different memory
configurations from one U-Boot instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: fa33d20749 ("mmc: split fsl_esdhc driver for i.MX")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
The extcsd read target must be cache aligned in case the controller
uses DMA to read the extcsd register, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This patch try to avoids eviction of dirty lines during DMA
transfer. The code right now execute the following step:
- allocate the buffer
- start a dma operation using the non-coherent dma buffer
- invalidate cache lines associated with the buffer
- read the buffer
This can lead to reading back not valid information, because the cache
controller could evict dirty cache lines belonging to the buffer *after*
the DMA operation has started to fill the DRAM.
In order to avoid this, a new invalidation is required *before* starting
the DMA operation. The patch just adds an invalidation before submitting
the DMA command.
Example below shows the nvme disk scan result without the following
patch
=> nvme scan
nvme_get_info_from_identify: nn = 544502629, vwc = 100,
sn = dev_0T, mn = `�\�, fr = t_part, mdts = 105
So, invalidating the cache before submitting the admin command,
fix the cpu read.
Cc: André Przywara <andre.przywara@arm.com>
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The correct name for the property is "qca,clk-out-frequency", so fix
it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Commit 0528979fa7 ("part: Drop disk_partition_t typedef") changed to
a struct. As a result it uncovered an apparent missing include in
zfs_common.h for part.h which actually contains the definition. The ZFS
handles the struct exclusively as pointers so it was only a warning.
warning: ‘struct disk_partition’ declared inside parameter list
will not be visible outside of this definition or declaration
void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info);
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Series-CC: Simon Glass <sjg@chromium.org>
After enabling SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC the MMC
initialization code is not longer needed.
This patch removes the unused code.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
In order to take the beneficts of DT and DM in SPL, like reusing the code
and avoid redundancy, enable SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC.
With this new configuration SPL image is 50 KB, higher than the
38 KB from the previous version, but it still under the 68 KB limit.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
In SPL legacy code only one MMC device is created, based on BOOT_CFG
register, which can be either SD or eMMC. In this context
board_boot_order return always MMC1 when configure to boot from
SD/eMMC. After switching to DM both SD and eMMC devices are created
based on the information available on DT, but as board_boot_order
only returns MMC1 is not possible to boot from eMMC.
This patch customizes board_boot_order taking into account BOOT_CFG
register to point to correct MMC1 / MMC2 device. Additionally, handle
IO mux for the desired boot device.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
Since the i.MX8 GPIO banks are indexed from 0 not 1 on other i.MX
platforms, so we have to adjust the index accordingly.
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
We need to change the environment offset to avoid corrupting the U-Boot
binary when saving it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the boot from USB loader, which is critical to easy the
manufacture process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
There are systems where board_early_init_f() is plain empty. Switch
the config option from "select" to "imply", to permit user to unset
the BOARD_EARLY_INIT_F if it were to be empty.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This is needed to obtain the MAC from EEPROM/OTP only after the final
env is populated, otherwise the ethaddr might be overriden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Harald Seiler <hws@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It appears that MMC access on the Sabrelite has been broken since
cdcaee9518:
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment
Remove the board_mmc_init() and related entries now that we should be
using DM_MMC, add PINCTRL so that things work as expected.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This introduces automatic boot counter that increases after every
reset.After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it's
disabled if bootlimit isn't set.
To enable this feature you have set bootcount limit ("bootlimit"),
alternate boot action ("altbootcmd") that will be performed if
the new value of bootcount exceeds the value of bootlimit, and
"upgrade_available" to let U-Boot automatically increase and save
the counter value after every reset:
> setenv bootlimit 5
> setenv upgrade_available 1
> setenv altbootcmd "bootm ..."
In case the bootlimit exceeds, the message will be shown and
albootcmd executed:
Warning: Bootlimit (5) exceeded. Using altbootcmd.
To reset bootcount run:
> bootcount reset
Print current value:
> bootcount print
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
s/fdt-module/fdt_module/g, as we don't use dash in fdt_file anymore.
Fixes: 4c63a601("apalis-tk1: support v1.2 hardware revision")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The distro bootscript uses kernel_image to get the file name of
the kernel, so change that variable name.
UBI boot has precedence in the default boot command. If one wants
to boot from SD with a working NAND installation stop in U-Boot
and enter:
setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
When using distro boot to boot from UBI volumes the boot partition
has been hardcoded to "UBI" (capital letters). However, our default
MTD layout uses "ubi" (lower case letter). Define "ubi" as the
default UBI partition for distro boot for Toradex. This allows to
use distro boot without having to redefine the MTD partition layout
which is useful for TorizonCore.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
