Rather than reusing the 'reg' property, use an explicit property for the
expected ping value used in testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tun on DEBUG in malloc(). This adds code space and slows things down but
for sandbox this is acceptable. We gain the ability to check for memory
leaks in tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set up and zero global data before board_init_f() is called so that we can
remove the need for CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: Simon Glass <sjg@chromium.org>
If we are to have driver model before relocation we need to support some
way of calling memory allocation routines.
The standard malloc() is pretty complicated:
1. It uses some BSS memory for its state, and BSS is not available before
relocation
2. It supports algorithms for reducing memory fragmentation and improving
performace of free(). Before relocation we could happily just not support
free().
3. It includes about 4KB of code (Thumb 2) and 1KB of data. However since
this has been loaded anyway this is not really a problem.
The simplest way to support pre-relocation malloc() is to reserve an area
of memory and allocate it in increasing blocks as needed. This
implementation does this.
To enable it, you need to define the size of the malloc() pool as described
in the README. It will be located above the pre-relocation stack on
supported architectures.
Note that this implementation is only useful on machines which have some
memory available before dram_init() is called - this includes those that
do no DRAM init (like tegra) and those that do it in SPL (quite a few
boards). Enabling driver model preior to relocation for the rest of the
boards is left for a later exercise.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f().
If we set up and zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change to simplify the init process.
Signed-off-by: Simon Glass <sjg@chromium.org>
These don't really serve any purpose in the modern age. On the other hand
they show up as annoying control characters in my editor, which then happily
removes them.
I believe we can drop these characters from the file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds the changes to boards.cfg and the board directory
under board/tqc.
TQMa6 is a family of modules based on Freescale i.MX6. It consists of
TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3
TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3
The modules need a baseboard. Initially the MBa6x starterkit mainboard is
supported. To easy support for other mainboards the functionality is splitted
in one file for the module (tqma6.c) and one file for the baseboard (tqma6_
mba6).
The modules can be boot from eMMC (on USDHC3) and SPI flash.
The following features are supported:
- MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard)
- Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module.
The phy needs special configurations for the pad skew registers to adjust for
the signal routing.
Also support for standard ethernet commands and uppdate via tftp.
- SPI: ECSPI1 with bootable serial flash on module and two additional
chip selects on MBa6x
- I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3)
and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x
are also configured.
- USB: high speed host 1 on MBa6x and support for USB storage
- PMIC: support for pfuze 100 on TQMa6<x>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
enable the W#/Vpp signal to disable writing to the status
register on ST MICRON flashes like the N25Q128 thorugh
the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
add basic support for the pwm modul found on imx6.
Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c
Commit "cd3de83f1476 Linux 3.16-rc4"
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
As a result of 0defddc851 , which did
a consolidation of the prompt string, this ifdef became empty. Remove
it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
On mx6solox there is an additional 0x4000 offset for the GPR registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
- Fix base address of I2C2 as 0x118100 instead of 0x119000.
- Add definitions for I2C3 & I2C4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resume from deep sleep, uboot needs to enable L2 and CPC
cache, or they would be keeping unusable in kernel because
kernel didn't enble or initialized them.
This patch didn't change the existing L2 cache enabling code,
just put them in a function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.
Signed-off-by: York Sun <yorksun@freescale.com>
On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
find_tlb_idx() is called in board_early_init_r() on multiple boards.
The return value is not checked before being used to disable a TLB.
In normal case the return value wouldn't be -1. In case of a mis-
configuration during porting to a new board, checking the return value
may be helpful to reveal some user errors.
Signed-off-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Internal SRAM has been incresed from 8KB to 16KB for IFC cotroller ver 2.0.
Update the page offset calculation logic to support the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Even u-boot boots up, the pcie link may not setup correctly when
Freescale SOC acts as endpoint.
So change the link status from 'no link' to 'undetermined' to
reduce the confusion.
The link status can check from host side eventually.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
IFC controller v1.1.0 requires internal SRAM initialize by reading
NAND flash. Higher controller versions have provided "SRAM init" bit in
NCFGR register space.
update SRAM initialize logic to reflect the same.
Also print error message in case of Page read error.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The number of chip select used by IFC controller vary from one SoC to other.
For eg. P1010 has 4, T4240 has 8.
Update MAX_BANKS same as SoC defined
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove unnecessary condition CONFIG_RAMBOOT_PBL to
have SST and EON SPI flash work in case of NOR boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Some of the fm_port_to_index() callers did not check for -1 return value and
used -1 as an array index.
Signed-off-by: Marian Rotariu <marian.rotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On some SoC(e.g. T2080/T4240) the 3rd DMA is not functional if SRIO2 is
chosen. we add fdt_fixup_dma3() to disable the 3rd DMA if SRIO2 is chosen.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit ddc94378d changed the definition of __kernel_size_t
from unsigned int to unsigned long.
It is true that it fixed warnings on some crosstools
but it increased warnings on the others.
The problem is that we cannot see consistency in terms of
the typedef of __kernel_size_t on M68K architecture.
However, I'd like to suggest to have __kernel_size_t to be
unsigned int again.
Rationale:
[1] Linux Kernel defines __kernel_size_t on M68K as unsigned int.
Let's stick to the Linux's way.
[2] We want to build boards with popular pre-built toolchains,
not the one locally-built by indivisuals.
I think m68-linux-gcc which can be downloaded from www.kernel.org
is the candidate for our _recommended_ toolchains.
With this patch, all the m68k boards can be built without any warnings.
Give it a try with the following crosstools:
https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.6.3/
x86_64-gcc-4.6.3-nolibc_m68k-linux.tar.xz
or
https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/
x86_64-gcc-4.9.0-nolibc_m68k-linux.tar.xz
(The latter is newer.)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jason Jin <Jason.jin@freescale.com>
The latest GCC is so clever that it reports more warnings
than old ones did:
------------------------------>8------------------------------
board/freescale/m5253demo/flash.c: In function 'flash_get_offsets':
board/freescale/m5253demo/flash.c:65:23: warning: iteration 2047u
invokes undefined behavior [-Waggressive-loop-optimizations]
info->start[k + 1] = info->start[k] + CONFIG_SYS_SST_SECTSZ;
^
board/freescale/m5253demo/flash.c:64:3: note: containing loop
for (k = 0, j = 0; j < CONFIG_SYS_SST_SECT; j++, k++) {
^
------------------------------8<------------------------------
The cause of the warning is like this:
The for statement iterates 2048 times in flash_get_offsets() func.
(Notice CONFIG_SYS_SST_SECT is defined as 2048)
The last iteration does
info->start[2048] = info->start[2047] + CONFIG_SYS_SST_SECTSZ;
causing an undefined behavior.
(Please note the array size of info->start is 2048.
CONFIG_SYS_MAX_FLASH_SECT is defined as 2048 for this board.)
This commit fixes that so as not to overrun the info->start array.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
This has been disabled for ARM in initr_scsi since that function was
introduced. However it works fine for me on Cubieboard and Cubietruck (with the
upcoming AHCI glue patch).
I also tested on two random ARM platforms which seem to define CONFIG_CMD_SCSI:
- highbank worked fine (on midway hardware)
- omap5_uevm built OK and I confirmed using objdump that things were as
expected (i.e. the default weak scsi_init nop was used).
While there remove the mismatched comment from the #endif (omitting the comment
seems to be the prevailing style in this file).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
In 73545f75b6 "ahci: wait longer for link" I increased the
timeout to 40ms based on the observed behaviour of a WD disk on a
Cubietruck. Since then Karsten Merker and myself have both
observed timeouts with HGST disks (Karsten on Cubietruck, me on
Cubieboard2). Increasing the timeout to ~175ms fixes this, so go
to 200ms for a bit of headroom.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
There have been /errlog and /reloc_off in the top level .gitignore
since commit 1b4aaffe added it about 7 years ago.
But they are no longer generated.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add more entries to .mailmap for the canonical names with
50 commits or more.
This commit was generated by the following command:
scripts/mailmapper > tmp; mv tmp .mailmap
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This tool helps to create/update the mailmap file.
It runs 'git shortlog' internally and searches differently spelled author
names which share the same email address. The author name with the most
commits is asuumed to be a canonical real name. If the number of commits
from the cananonical name is equal to or greater than 'MIN_COMMITS' (=50),
the entry for the cananical name will be output. ('MIN_COMMITS' is used
here because we do not want to create a fat mailmap by adding every author
with only a few commits.)
If there exists a mailmap file specified by the mailmap.file configuration
options or '.mailmap' at the toplevel of the repository, it is used as
a base file.
The base file and the newly added entries are merged together and sorted
alphabetically (but the comment block is kept untouched), and then printed
to standard output.
Usage
-----
scripts/mailmapper
prints the mailmapping to standard output.
scripts/mailmapper > tmp; mv tmp .mailmap
will be useful for updating '.mailmap' file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is the first version of .mailmap created by hand.
Please see "man git-shortlog" for what this commit is trying to do.
Without this file, for example, "git shortlog -n -s" shows as follows:
2693 Wolfgang Denk <------
1002 Stefan Roese <------
811 wdenk <------
808 Mike Frysinger
806 Simon Glass
[snip]
177 Matthias Fuchs
154 stroese <------
153 Timur Tabi
And then, with this file, it shows as follows:
3504 Wolfgang Denk <------
1156 Stefan Roese <------
808 Mike Frysinger
806 Simon Glass
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
