Qemu v4.2.0 maps bootmode registers to address space which was the reason
why board_late_init() was disabled and accesses were failing.
With new Qemu board_late_init() can be called without any issue.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables bitstream loading support for Versal platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch increases SYS_MALLOC_F_LEN as the versal clock
driver needs to be probed before relocation itself inorder
to get required clocks before relocation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds usb host and device mode support for Xilinx
Versal virtual platform. By default USB host functionality
is enabled. To use in usb device mode, set dr_mode property
in DT to peripheral.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable device tree overlay to build all dtbs for Versal with -@ flag to
enable applying overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable GPIO command for Xilinx Versal platform. Driver is updated that's
why it can be used directly. Driver is enabled by default through Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the debug uart configuration from versal virtual defconfig.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This platform is going to become generic that's why it is necessary also
enable different PHY vendors.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Virtual QEMU board is generating DTB self and putting it to
VERSAL_QEMU_DTB_ADDR address.
Board is using CONFIG_OF_BOARD which ensures that u-boot is aligned with
board created by QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
