We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Some of the regulators we need to successfully boot are fixed
regulators. Enable the driver to properly probe them.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Apple machines do not have memory below 4G. Since U-Boot does
not support the SMBIOS 3 header structures this means we can't
support SMBIOS on these machines. Unfortunately the refactoring
of the SMBIOS code this cycle accidentally enabled it again.
Fixes: 53fab13a7b ("efi: Use the installed SMBIOS tables")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Since commit b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
and commit e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Amlogic boards now requires DM_USB_GADGET to have USB Gadget to work.
Add it to the boards configs as returned by:
$ grep -L DM_USB_GADGET $(grep -l CONFIG_USB_GADGET $(grep -l MESON configs/*))
Fixes: b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
Fixes: e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Link: https://lore.kernel.org/r/20231206-u-boot-m2s-fix-usb-gadget-v1-1-1c4c66cd10f3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581 ("sunxi: H616: enable USB support for H616 boards")
Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As correct default SYS_CONFIG_NAME value is now set in
board/samsung/axy17lte/Kconfig (in commit "board: samsung: Fix
SYS_CONFIG_NAME configs in axy17lte Kconfig"), the SYS_CONFIG_NAME
option can be safely removed from all a*y17lte defconfigs. That removal
doesn't change resulting .config files.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
Now that Ringneck requires some board-specific code (namely resetting
the MCU companion controller) to be run during SPL stage, let's enable
SPL_BOARD_INIT.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is
0x160000 . Define this size in U-Boot config to prevent misconfigured
builds from emitting larger u-boot.itb than the one which fits the
SPI NOR area reserved for the blob.
The SPI NOR layout is as follows:
0x00_0000..0x03_ffff ... SPL 1
0x04_0000..0x07_ffff ... SPL 2
0x08_0000..0x1d_ffff ... U-Boot
0x1e_0000..0x1e_ffff ... Environment 1
0x1f_0000..0x1f_ffff ... Environment 2
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This is a useful tool to check the presence of a device on a specific
i2c bus, so let's enable it.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit
widths of DMA. This significantly improves read and write throughput.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231027030446.4009-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As mini configs are required only for flashing the images, so
disabling the lock config which will save nearly 6KB of memory.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As mini configs are required only for flashing the images, so
disabling the lock config which will save nearly 6KB of memory.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.
The default boot will read a uImage from flash and boot it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move ASUS Transformers, Grouper, P895 and P880 config fragments into
their respective device directory in /board/../configs/
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Convert refresh USB to enter console. Transformers have full size
USB and a dock keyboard so access to U-Boot console would be handy.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Change boot logic to primary try to boot from USB in dock, then
from microSD and lastly from eMMC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Enables JH7110 RNG driver to visionfive2 board.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
enable PSCI reset used for the system reset
Even though Corstone-1000 does not implement the entire PSCI APIs,
it relies on PSCI reset interface for the system reset.
Signed-off-by: Emekcan Aras <emekcan.aras@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
unzip the kernel before executing it
The Corstone-1000 kernel has become too large to fit in the available
storage. Switching to a compressed kernel avoids the problem, but
requires uncompressing it.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
QEMU print and console buffer sizes have been restricted on QEMU below
their default values.
One of the side effects of the print buffer size restriction is output
truncation of the 'efidebug dh' command.
As QEMU does not have special memory size restrictions remove the settings
from the defconfig files and go with the generic defaults.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Fixes: d31466b382 ("Convert CONFIG_SYS_CBSIZE to Kconfig")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable USB device and fastboot support which may be used to load the
Toradex Easy Installer FIT image.
While at it also enable USB mass storage aka UMS support.
Note that the i.MX 8M Plus recovery mode support is based on the USB
boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial
downloader support.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
-----BEGIN PGP SIGNATURE-----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=gvDs
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-27102023' of https://source.denx.de/u-boot/custodians/u-boot-tpm
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
- Fix environment saving for new Android boot features on vim3*_android
- Add SPIFC support for Amlogic A1
- Add DFU RAM boot step when booting over USB
