SPL environments don't need commands that they can never use.
Avoid errors with CONFIG_IS_ENABLED conversions by skipping them now.
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_IS_ENABLED(SPL_X86_32BIT_INIT)
would check for CONFIG_SPL_SPL_X86_32BIT_INIT for SPL builds
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Avoid error messages when SPL,TPL,VPL build don't
have the environment options of the main build.
This is needed when defined(CONFIG_ENV_IS_IN_xxx) is changed
to CONFIG_IS_ENABLED(ENV_IS_IN_xxx).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
The AM64x SR2.0 SK board uses "AM64B-SKEVM" as the EEPROM identifier.
This board is similar to the AM64x SKEVM except that it has a new
PMIC that will be enabled in the future and consequently could use a
different device tree file in the future.
For now we treat the board same as an AM64x SK.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add method to remove video driver before loading u-boot proper. When
bootstage changes from SPL to u-boot proper, noo method is called to
remove video driver, and at u-boot proper if video driver is not
enabled, the video driver starts displaying garbage on the screen,
because there is no reserved space for video and the frame buffer gets
u-boot proper data written.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
To enable splash screen on AM62x at a53 SPL setup DRAM, set page table,
enable cache to allow copying of bmp image to frame buffer and display
it using splash_display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Change splashimage which is bmp image loadaddr to 0x80200000 since stack
is situated at 0x80477660 as splash framework requires bmp image to be
present above stack.
Change splashsource to sf to support loading bmp image from ospi flash
memory.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
btrfs_read_extent_reg correctly computed the extent offset in the
BTRFS_COMPRESS_NONE case, but did not account for the 'offset - key.offset'
part correctly in the compressed case, making the function read
incorrect data.
In the case I examined, the last 4k of a file was corrupted and
contained data from a few blocks prior, e.g. reading a 10k file with a
single extent:
btrfs_file_read()
-> btrfs_read_extent_reg
(aligned part loop, until 8k)
-> read_and_truncate_page
-> btrfs_read_extent_reg
(re-reads the last extent from 8k to the end,
incorrectly reading the first 2k of data)
This can be reproduced as follow:
$ truncate -s 200M btr
$ mount btr -o compress /mnt
$ pat() { dd if=/dev/zero bs=1M count=$1 iflag=count_bytes status=none | tr '\0' "\\$2"; }
$ { pat 4K 1; pat 4K 2; pat 2K 3; } > /mnt/file
$ sync
$ filefrag -v /mnt/file
File size of /mnt/file is 10240 (3 blocks of 4096 bytes)
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 2: 3328.. 3330: 3: last,encoded,eof
$ umount /mnt
Then in u-boot:
=> load scsi 0 2000000 file
10240 bytes read in 3 ms (3.3 MiB/s)
=> md 2001ff0
02001ff0: 02020202 02020202 02020202 02020202 ................
02002000: 01010101 01010101 01010101 01010101 ................
02002010: 01010101 01010101 01010101 01010101 ................
(02002000 onwards should contain '03' pattern but went back to 01,
start of the extent)
After patch, data is read properly:
=> md 2001ff0
02001ff0: 02020202 02020202 02020202 02020202 ................
02002000: 03030303 03030303 03030303 03030303 ................
02002010: 03030303 03030303 03030303 03030303 ................
Note that the code previously (before commit e3427184f3 ("fs: btrfs:
Implement btrfs_file_read()")) did not split that read in two, so
this is a regression even if the previous code might not have been
handling offsets correctly either (something that booted now fails to
boot)
Fixes: a26a6bedaf ("fs: btrfs: Introduce btrfs_read_extent_inline() and btrfs_read_extent_reg()")
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Move the handler for "tlv_eeprom dev X" command to the beginning of
do_tlv_eeprom, to allow using it before issuing a "read" command for
currently selected eeprom.
Also remove the check if eeprom exists, since that can only work after
the first execution of read_eeprom triggered device lookup.
Instead accept values up to the defined array size (MAX_TLV_DEVICES).
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
When tlv eeprom does not exist, return error code instead of quietly
making up tlv structure in memory.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
has_been_read is only used as an optimization for do_tlv_eeprom.
Explicitly use and set inside this function, thus making read_eeprom
stateless.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make tlv_eeprom command device selection an explicit parameter of all
function calls.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Request the reset gpio of the rgmii-id phy as output to be consistent
with the eth-phy-uclass driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Add minimal support for 8125B version.
Changes are based on the Linux driver.
Tested on Radxa Rock 5B Rk3588 board.
Connection to a laptop worked fine in 100 Mbps mode.
1000 Mbps mode is not working at the moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Test the IPv6 network discovery feature if indicated by boardenv file.
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
In IPv6, the default gateway and prefix length are determined by receiving
a router advertisement as defined in -
https://www.rfc-editor.org/rfc/rfc4861.
Add support for sending router solicitation (RS) and processing router
advertisements (RA).
If the RA has prefix info option and following conditions are met, then
gatewayip6 and net_prefix_length of ip6addr env variables are initialized.
These are later consumed by IPv6 code for non-local destination IP.
- "Router Lifetime" != 0
- Prefix is NOT link-local prefix (0xfe80::/10)
- L flag is 1
- "Valid Lifetime" != 0
Timing Parameters:
- MAX_RTR_SOLICITATION_DELAY (0-1s)
- RTR_SOLICITATION_INTERVAL (4s) (min retransmit delay)
- MAX_RTR_SOLICITATIONS (3 RS transmissions)
The functionality is enabled by CONFIG_IPV6_ROUTER_DISCOVERY and invoked
automatically from net_init_loop().
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>Reviewed-by:
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Recent commit 75d28899e3 ("net: phy: Synchronize PHY interface modes
with Linux") reordered the enum definitions. This exposed a problem
in range checking functions to identify the interface type. Though
this specific api wasn't impacted (all the RGMII definitions remained
within range), this experience should be used to never to have to face
this kind of challenge again.
While it is possible for the phy drivers to use the enums directly,
drivers such as dp83867, dp83869, marvell, micrel_ksz90x1 etc use this
api.
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Recent commit 75d28899e3 ("net: phy: Synchronize PHY interface modes
with Linux") reordered the enum definitions. This caused the range of
enums that this api was checking to go bad.
There aren't anymore users of phy_interface_is_sgmii, so, just drop
it. Also the protocols are so very different that it makes no sense to
provide a helper wrapper in the hope of reuse for phy drivers.
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Suggested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/all/20230414103852.38705065@dellmb/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
dp83867 driver only supports sgmii and not all the newer protocols.
Drop the usage of the generic phy_interface_is_sgmii function and just
matchup to the specific mode supported.
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Suggested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/all/b82ac325-4818-8e72-054b-640268dbf806@mailbox.org/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make following changes to unblock TCP fastboot support:
1. Implement being a TCP server support
2. Introduce dedicated TCP traffic handler (get rid of UDP signature)
3. Ensure seq_num and ack_num are respected in net_send_tcp_packet
function (make sure existing wget_cmd code is reflected with the fix)
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Requires proper environment with DHCP6 server provisioned.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds DHCPv6 protocol to u-boot.
Allows for address assignement with DHCPv6 4-message exchange
(SOLICIT->ADVERTISE->REQUEST->REPLY). Includes DHCPv6 options
required by RFC 8415. Also adds DHCPv6 options required
for PXE boot.
Possible enhancements:
- Duplicate address detection on DHCPv6 assigned address
- IPv6 address assignement through SLAAC
- Sending/parsing other DHCPv6 options (NTP, DNS, etc...)
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rtl8211e_startup() is an exact copy of genphy_startup(). Use that
instead of duplicating it.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Read the phy mode of the external phy from the device tree if available
and check that it is a RGMII variant.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
NFSv1 support added by Christian Gmeiner, Thomas Rienoessl,
September 27, 2018. As of now, NFSv3 is the default choice.
if the server does not support NFSv3, we fall back to
versions 2 or 1.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Without that patch it lost track to the node to scan
speed and duplex.
Patch was created by Marek Vasut, just tested by me.
Signed-off-by: Elmar Psilog <epsi@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Fix "setenv gatewayip6".
Synchronize IPv6 local variables with environment variables
in netboot_update_env()
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
In the process of adopting CONFIG_DM_ETH on the DPAA2 based platforms,
interfaces which were previously defined as "xgmii" were transitioned to
be defined as "xfi" in the DTS.
See the commit below for reference:
commit 87274918f2 ("arm: dts: ls2088ardb: add DPMAC and PHY nodes")
Then Vladimir's commit replaced all occurrences of "xfi" with
"10gbase-r" in an effort to make U-Boot work with the same device tree
as Linux.
commit 77b11f7604 ("net: replace the "xfi" phy-mode with "10gbase-r"")
These changes to the phy_interface_t of an Ethernet port meant that the
mc_fixup_mac_addrs() function was no longer capable to properly fixup
the MAC addresses. The problem arises from the fact that the hardcoded
information about an interface (wriop_get_enet_if()) was no longer
matching any actual device.
For example, the function tried to search for "DPMAC1@xgmii1" by name
using eth_get_dev_by_name() when only "DPMAC1@10gbase-r" was available.
This function removes the need to rely on the hardcoded information by
iterating through all the UCLASS_ETH devices which are DPAA2 and request
a fixup for each of them.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Export the ldpaa_eth_get_dpmac_id() function so that it can be used from
other drivers, especially by fsl-mc which will need it the next patch.
Also, create a macro for the Ethernet ldpaa driver name and export it as
well.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Add a port_probe function to configure the phy. This leads to
earlier link negotiation so the port is more likely to be ready
when used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We don't do anything useful with the master dev, so remove the variable.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
packet tagging is not used for this driver so we do not need to
call dsa_set_tagging.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
