Upstream commit 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY,
HSIOMIX clock") added usb_core_ref for USB Controller but never set it
to be used as a clock source, using rather "osc_32k" instead.
This produces following boot log message:
"clk_register: failed to get osc_32k device (parent of usb_root_clk)"
Fix the USB controller clock source by using usb_core_ref instead of
osc_32k.
Fixes: 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Root clock name contained underscore, which does not match to the actual
clock name.
Correct the name to match what is present in the FDT.
Fixes: 87f958810f ("clk: imx8mp: Add ECSPI clocks")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
systemd prints its messages on the last console= statement that it finds
in the kernel arguments. The current ordering sends the systemd messages
to tty1, by default this is the display.
Ensure that systemd sends its messages to the default UART, reorder the
console= statements accordingly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Since SoMs revision 1.9 the ar8035 phy has been replaced by adin1300.
Enable the driver so that the new SoMs have functional networking.
Signed-off-by: Josua Mayer <josua@solid-run.com>
SoM revision 1.9 has replaced the ar8035 phy address 0 with an adin1300
at address 1. Because early SoMs had a hardware flaw, the ar8035 can
also appear at address 4 - making it a total of 3 phy nodes in the DTB.
To avoid confusing Linux with probe errors, fixup the dtb to only enable
the phy node that is detected at runtime.
Signed-off-by: Josua Mayer <josua@solid-run.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The ADIN1300 supports generating certain clocks on its GP_CLK pin, as
well as providing the reference clock on CLK25_REF.
Add support for selecting the clock via device-tree properties.
This patch is based on the Linux implementation for this feature,
which has been added to netdev/net-next.git [1].
[2] https://patchwork.kernel.org/project/netdevbpf/cover/20220517085143.3749-1-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
Currently, the adin driver fails to compile.
The original patch introducing the adin driver used the function
phy_get_interface_by_name to support the adi,phy-mode-override
property. Unfortunately, a few days before the adin patch
was accepted, another patch removed support for phy_get_interface_by_name:
123ca114e0
This patch refactors adin_get_phy_mode_override, implementing the logic in
the new function, ofnode_read_phy_mode, from the patch above.
Signed-off-by: Nate Drude <nate.d@variscite.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
The imx8mn-ddr4-evk board has Ethernet support already, but the
lpddr4 board does not.
Add Ethernet support for the LPDDR4 variant too.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add the new Apalis iMX8 product variant
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
the only difference to the product
0037 Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
is the 8gb of RAM. Toradex strategy to choose the correct RAM timing in
SCFW is by fuses in the user area telling which RAM timing to load.
This commit makes use of this information to set the correct size of
the RAM and therefore distinguish between the new 0067 and 0037 product
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
This module is identical to its 4GB counterpart
0037: Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
except for the RAM size.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
This test was written to match up with the list of compatibles in
drivers/i2c/tegra_i2c.c so adding another one requires the test to be
updated to match.
Fixes: 0d2105ae5e ("arm: tegra: Update some DT compatibles")
Signed-off-by: Tom Rini <trini@konsulko.com>
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use device tree to set MAC address of the Ethernet chip.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some of the DT compatibles have changed upstream so add new DT compatibles
to ensure things continue to keep working if the device trees are
updated.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add new lines to make errorr messages easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add new lines for error messages to make them easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
UEFI:
* Ignore OsIndications if CONFIG_EFI_IGNORE_OSINDICATIONS=y
* Correct UEFI default binary name
* Let efidebug create boot options without file path
* Support booting with a boot option with shortened device only device path
-----BEGIN PGP SIGNATURE-----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=Ylyv
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc5
UEFI:
* Ignore OsIndications if CONFIG_EFI_IGNORE_OSINDICATIONS=y
* Correct UEFI default binary name
* Let efidebug create boot options without file path
* Support booting with a boot option with shortened device only device path
Allow booting from a short form device-path without file path, e.g.
/HD(1,GPT,5ef79931-a1aa-4c70-9d67-611e8f69eafd,0x800,0x1000)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Only on the sandbox the default EFI binary name (e.g. BOOTX64.EFI) must
match the host architecture.
In all other cases we must use the target architecture.
Use #elif where appropriate.
Reported-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The GetImageInfo function definitions for the FIT images and raw
images are the same. Use a common function for the both the Firmware
Management Protocol(FMP) instances for raw and FIT images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The EFI_IGNORE_OSINDICATIONS config symbol was introduced as a
mechanism to have capsule updates work even on platforms where the
SetVariable runtime service was not supported. The current logic
requires the OsIndications variable to have been set to a 64 bit value
even when the EFI_IGNORE_OSINDICATIONS config is enabled. Return an
error code on not being able to read the variable only when
EFI_IGNORE_OSINDICATIONS is not enabled.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for AM62x SoC identification.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add pinctrl macros for AM62x SoCs. These macro definitions are similar
to that of previous platforms, but adding new definitions to avoid any
naming confusions in the SoC dts files.
checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses
However, we do not need parentheses enclosing the values for this
macro as we do intend it to generate two separate values as has been
done for other similar platforms.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phy used in the 8 bit instance has been changed to the phy used in 4
bit instance on AM62 SoC. This implies the phy configuration required for
both the instances of mmc are similar. Therefore, add a new compatible
for AM62 SoC using the driver data of am64 4 bit instance.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Sync the configs required for enabling checks for size of image and stack
from generic r5 defconfig file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
This commit sets two additional variables in the default BOOTCOMMAND.
Adding 'boot=mmc' and 'addr_fit=0x8b000000' removes the need for a
special 'uEnv.txt' to be created. The 'addr_fit' variable is the key
piece here. It is normally defined as 0x90000000, in the macro
DEFAULT_FIT_TI_ARGS. For this OMAP34XX board, 0x8b000000 works without
touching other varibles. This was tested with a 'fitImage' created
using the following FIT source:
----------------------------------------------------------------------
/dts-v1/;
/ {
description = "Simple image with single Linux kernel and FDT blob";
#address-cells = <1>;
images {
kernel {
description = "Linux kernel: omap2plus";
data = /incbin/("./zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0x80008000>;
entry = <0x80008000>;
hash-1 {
algo = "sha256";
};
};
fdt-omap3-evm.dtb {
description = "FDT: omap3-evm.dtb";
data = /incbin/("./omap3-evm.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
load = <0x8ff00000>;
hash-1 {
algo = "sha256";
};
};
};
configurations {
default = "conf-omap3-evm.dtb";
conf-omap3-evm.dtb {
description = "Boot Linux kernel with FDT blob";
kernel = "kernel";
fdt = "fdt-omap3-evm.dtb";
};
};
};
----------------------------------------------------------------------
Additionally, the default environment is now stored in "uboot.env" on
the FAT partition of MMC '0'.
Fixes: 11e2ab3f0b ("ARM: omap3: evm: Enable booting 'fitImage' with DEFAULT_FIT_TI_ARGS")
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
