This converts the following to Kconfig:
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.
Signed-off-by: Tom Rini <trini@konsulko.com>
The loading address is too close to the kernel address, so newer kernels
may overlap memory space, so loading the device tree may corrupt zImage.
This patch moves the fdt_addr_r to 0x14000000 which is also consistent
with guidance that the kernel be allocated 32MB. This places it
in the same place as the ramdisk, so this patch moves the ramdisk address
512KB after the fdt.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.
For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.
It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.
Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds an extra, optional environmental variable called
'optargs' which if enabled allow additional parameters to be
passed to the kernel (ie, quiet, cma=128M, etc.)
Each script that setups the bootargs will just append this.
Signed-off-by: Adam Ford <aford173@gmail.com>
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <aford173@gmail.com>
A few scripts reference 'fdt_addr' when they should reference
'fdt_addr_r' so this patch fixes those broken references.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
There are already definitions for ramdisk_addr_r and fdt_addr_r, so
having a duplicate copy called ramdiskaddr and fdtaddr is confusing.
This patch converts any references to ramdisk_addr_r and fdt_addr_r
and removes the duplicates.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since CONFIG_MXC_UART is already in Kconfig, move this from
the header to imx6q_logic_defconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
