Commit graph

379 commits

Author SHA1 Message Date
Tom Rini
8bf3c2442b Improvements:
- init DRAM for RK322x in SPL
 - add FAN53555 PMIC/regulator driver
 - update MicroCrystal RV3029 driver to Kconfig and sync from Linux
 - add bootcount uclass and first DM-driver for bootcount
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
 Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
 VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
 9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
 A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
 jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
 =5sHL
 -----END PGP SIGNATURE-----

Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip

Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
2018-12-10 10:19:09 -05:00
Philipp Tomsich
dfb0a70a1a power: add FAN53555 family support
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.

While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.

Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
  - switching the selected voltage (via a GPIO)
  - disabling the voltage output via software-control
This matches the functionality of the Linux driver.

Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2018-12-10 10:04:45 +01:00
Jean-Jacques Hiblot
fb1b7712ad power: make most tps drivers and the twl4030 driver compatible with DM_I2C
Those driver are not DM drivers per se (not using the PMIC/regulator
framework) and are using the legacy I2C API. Make them compatible with
the DM_I2C API.

This impacts the following drivers:
- palmas (used by am57xx/dra7xx evms)
- tps65218 (used by am43xx evms)
- tps65217 and tps65910 (used by am335x evms and am335x boneblack vboot)
- twl4030 (used by omap3_logicpd)
- tps65217 (used by brppt1)
- twl6030

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:17:30 +01:00
Olliver Schinagl
ef52605ebe power: axp209: Limit inrush current for broken boards
Some boards feature a capacitance on LDO3's output that is too large,
causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.

A fix appeared to be done with
commit 0e6e34ac8d ("sunxi: Olimex A20 boards: Enable LDO3 and LDO4 regulators").

The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system freezes.

While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.

To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Olliver Schinagl
61436d502b power: axp209: Add support for voltage rate control on LDO3
The AXP209 LDO3 regulator supports voltage rate control, or can set a
slew rate.

This allows for the power to gradually rise up to the desired voltage,
instead of spiking up as fast as possible. Reason to have this can be
to reduce the inrush currents for example.

There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.

In ideal world (where vendors follow the recommended design guidelines)
this setting should not be enabled by default. Unless of course AXP209
crashes instead of reporting overcurrent condition as it normally should
do in this case.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Olliver Schinagl
3f7d76a7ed power: axp209: Reduce magic values by adding defines for LDO[234]
The AXP209 has a few 'magisc-ish' values that are better served with
clear defines.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Olliver Schinagl
f5eebc7925 power: axp209: Define the chip version mask
Use a define for the chip version mask on the axp209.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Patrick Delaunay
4f86a724e8 power: regulator: denied disable on always-on regulator
Don't disable regulator which are tagged as "regulator-always-on" in DT.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jack Mitchell <jack@embed.me.uk>
Tested-by: Jack Mitchell <jack@embed.me.uk>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Richard Röjfors <richard@puffinpack.se>
Tested-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
2018-12-05 06:06:44 -07:00
Simon Glass
031a650e13 dm: sandbox: i2c: Use new emulator parent uclass
Update the device tree, sandbox i2c driver and tests to use the new
emulation parent to hold emulators.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-11-29 09:30:05 -07:00
Simon Glass
c83c436de0 power: pmic: Correct debug/error output
There is a newline missing from quite a few printf() strings in these pmic
files. Fix them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-11-29 09:30:05 -07:00
Ryder Lee
9dec738a8b power domain: MediaTek: add power domain driver for MT7623 SoC
This adds power domain (scpsys) support for MT7623 SoC.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:53 -05:00
Ryder Lee
2ae7e4dc63 power domain: MediaTek: add power domain driver for MT7629 SoC
This adds a power domain driver for the Mediatek SCPSYS unit.

The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.

For now this driver only adds power domain support.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:53 -05:00
Lokesh Vutla
26da01f700 power: spl: add SPL_DM_REGULATOR_GPIO in Kconfig
The Makefile already tests for SPL_DM_REGULATOR_GPIO, but Kconfig
does not provide it. This adds SPL_DM_REGULATOR_GPIO to Kconfig.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-01 10:02:43 -04:00
Patrick Delaunay
22929e1266 drivers: cosmetic: Convert SPDX license tags to Linux Kernel style
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-28 09:26:39 -04:00
Peng Fan
d526f340f7 power: Add power domain driver for i.MX8
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"

When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.

When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.

There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.

The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Adam Ford
e5f7a261db regulator: pbias: Add additional compatible flags
The driver was developed with references for more than just
dra7, but never included.  At least for omap3, this appears
to be functional.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:38:37 -04:00
Andreas Dannenberg
1a88a04e9f power domain: Introduce TI System Control Interface (TI SCI) power domain driver
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.

This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.

This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
2618cf3657 power domain: Add support for multiple powerdomains per device
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Neil Armstrong
8d5579ceff power: domain: Add the VPU Power Domain driver
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.

This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-09-10 20:48:17 -04:00
Peng Fan
39dd00fc5d drivers: regulator: fixed: add u-boot, off-on-delay-us
Add u-boot,off-on-delay-us for fixed regulator.

Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-08-19 20:38:39 -04:00
Peng Fan
e13278c943 power: Add CONFIG_SPL_POWER_DOMAIN config
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-08-06 11:51:10 +02:00
Michal Simek
b8448051df Kconfig: Remove trailing whitespaces in prompt
Remove additional trailing whitespaces in prompt reported by kconfiglib:

warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
2018-07-30 07:18:46 -04:00
Christophe Kerello
844f9bf1ee power: regulator: stpmu1: add power off delay
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-19 16:31:36 -04:00
Trent Piepho
7da7ff5491 power: pmic: Let PFUZE3000 see all 256 registers
The PFUZE3000 uses registers addresses up to 0xff.

The DM pfuze100 driver supports both pfuze100 and pfuze3000.  Allow it
to use the device type to return the correct number of registers.

Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.

Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-27 09:47:46 +02:00
Álvaro Fernández Rojas
34c0fc3fab power: domain: bcm6328: convert to use live dt
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Lukasz Majewski
a65e644033 sandbox: Rewrite i2c_pmic_emul.c to support PMIC with 3 bytes transmission
This change enables support for MC34708 PMIC in sandbox. Now we can
emulate the I2C transfers larger than 1 byte.

Notable changes for this driver:

- From now on the register number is not equal to index in the buffer,
  which emulates the PMIC registers

- The PMIC register's pool is now dynamically allocated up till
  64 regs * 3 bytes each = 192 B

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-18 08:27:26 +02:00
Lukasz Majewski
c57a226ac4 pmic: dm: Add support for MC34708 for PMIC DM
This patch adds support for MC34708 PMIC, to be used with driver model
(DM).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-18 08:27:26 +02:00
Lukasz Majewski
655b24cea6 pmic: dm: Rewrite pmic_reg_{read|write|clrsetbits} to support 3 bytes transmissions
This commit provides support for transmissions larger than 1 byte for
PMIC devices used with DM (e.g. MC34708 from NXP).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-18 08:27:26 +02:00
Lukasz Majewski
b8a6d6777b pmic: Add support for setting transmission length in uclass private data
The struct uc_pmic_priv's trans_len field stores the number of types to
be transmitted per PMIC transfer.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-18 08:27:26 +02:00
Marcel Ziswiler
4616e33b6a power: as3722: fix ldo_get/set_enable for ldo index bigger than 7
Fix ldo_get_enable() and ldo_set_enable() functions for LDOs with an
index > 7. Turns out there are actually two separate AS3722_LDO_CONTROL
registers AS3722_LDO_CONTROL0 and AS3722_LDO_CONTROL1. Actually make use
of both. While at it also actually use the enable parameter of the
ldo_set_enable() function which now truly allows disabling as opposed to
only enabling LDOs.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:20 -07:00
Tom Rini
14249635b6 Merge git://git.denx.de/u-boot-mmc 2018-05-08 13:47:39 -04:00
Fabrice Gasnier
93cf0ae775 power: regulator: Add support for stm32-vrefbuf
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-08 09:07:39 -04:00
Patrice Chotard
1f0dfa1fa0 power: pmic: stpmu1: Add regulator bindings
Add regulator bindings to get access to regulator managed
by drivers/power/regulator/stpmu1.c regulator driver.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-08 09:07:38 -04:00
Christophe Kerello
069f0b6354 power: regulator: stpmu1: Introduce stpmu1 driver
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-08 09:07:38 -04:00
Andy Yan
e1fd9e6bb8 power: pwm regulator: support live tree
Use live tree compatible api for pwm regulator.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2018-05-08 13:12:33 +09:00
Jaehoon Chung
9c67c4491e power: pmic_max77686: remove the old pmic_max77686 file
max77686 pmic is supporting with max77686.c under pmic/ and regulator/
direnctroy. Remove pmic_max77686.c what didn't use anywhere.
Instead, enable CONFIG_DM_REGULATOR_MAX77686 and
CONFIG_DM_PMIC_MAX77686.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-05-08 13:12:33 +09:00
Tom Rini
4549e789c1 SPDX: Convert all of our multiple license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document.  Note that parenthesis are
allowed so when they were used before we continue to use them.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 10:24:31 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Heinrich Schuchardt
4bf225aa87 drivers:power:max77693: remove redundant logical constraint
As ret is not set when calling max77693_get_vcell() there is no
need to check ret again.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-02 10:57:43 +09:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Heinrich Schuchardt
c57b6b7090 regulator: pbias: don't evaluate variable before assignment
We should not evaluate the value of reg before its value is set.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-06 20:45:28 -04:00
Tom Rini
c17848a798 Merge git://git.denx.de/u-boot-sunxi 2018-03-19 18:39:14 -04:00
Patrick Delaunay
5d0c74e624 pmic: add stpmu1 support
This driver implements register read/write operations for STPMU1.

The STPMU1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF
and 2 power switches. It is accessed via an I2C interface.
This device is used with STM32MP1 SoCs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:21 -04:00
Jagan Teki
735fb25202 sunxi: Add AXP_PMIC_BUS kconfig entry
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Peng Fan
a35332fa28 power: pmic/regulator allow dm be omitted by SPL
Allow the dm driver be omitted by SPL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-04 12:00:58 +01:00
Jaehoon Chung
173f023f46 power: pmic: s2mps11: probe the regulator driver
Add the probe function to support the s2mps11 regulator driver.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
2018-01-24 16:07:35 +09:00
Jaehoon Chung
60599ea6cd power: regulator: s2mps11: add a regulator driver for s2mps11
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
2018-01-24 16:07:19 +09:00
Tom Rini
8c0bb85824 power: Rearrange code to guard power command with CONFIG_SPL_BUILD guard
In order to discard this code when unused in SPL we need to guard the
command with a check for CONFIG_SPL_BUILD and we rearrange the code
slightly to make this cleaner.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-13 00:07:57 +09:00
Felix Brack
46caea7f96 power: tps65910: replace error() by pr_err()
The patch replaces the former error() by the new pr_err().
This makes the TPS65910 driver conform to Masahiro's patch
'treewide:replace with error() with pr_err()' introduced
October 2017.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-01 09:04:19 -05:00