The existing calibration values were found to be incorrect
in comparison to newly determined values.
The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase
the "size" of the dfu_alt_info setting.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Just give the new Ethernet PHY power save mode circuitry time to settle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Currently $loadaddr and $fdt_addr_r point to the same address. This
might be not ideal for some distro boot scripts which make use of
$loadaddr after loading the device tree.
Make sure the two variables point to two different addresses. Moving
$loadaddr is not entirly trivial since it is defined in mx6_common.h.
Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough
for scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add support for new Colibri iMX6ULL SKUs.
While at it also checkpatch fix the whole files.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Fix indentation using tab vs. spaces.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
To make it easy to add new clk driver for i.MX8, split
the code into common part and SoC specific part.
Make the get/set/enable non static and introduce a num_clks for
soc_clk_dump, because the arrays are moved to clk-imx8qxp.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This setup is a bit special as Linux kernel (4.19) is not supporting
in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA)
operation.
For that reason it was necessary to provide a bootarg to allow userspace
enable it afterwards if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed
anymore and should be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As EHCI on i.MX5 has been converted to driver model, the board specific
code, necessary for VBUS USB power supply setup is not needed anymore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After unification of the rootfs for both HSC and DDC devices, only one,
common wic file is necessary - without the distinction of specific board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
