This patch will create a new board, SIMPC8313, from Sheldon Instruments. This
board boots from NAND devices and is configureable for either large or small
page devices. The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running in PCI agent mode, the PCI_CLK_OUT signals are not used, so do
not enable them. See the MPC8349EA Reference Manual, Section 4.4.2
"Clocking in PCI Agent Mode".
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
lowlevel_init of SH was corrected to use the write/readXX macro.
However, there was a problem that was not able to be compiled partially.
This patch corrected this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds esd's loadpci BSP command to CPCI4052 and
CPCI405AB board. This requires CONFIG_CMD_BSP and CONFIG_PRAM.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch cleans up CPCI405 board support:
- wrap long lines
- unification of spaces in function calls
- remove dead code
Use correct io accessors on peripherals.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch turns on the auto RS485 mode in the 2nd external
uart on PLU405 boards. This is a special mode of the used
Exar XR16C2850 uart. Because these boards only have a 485 physical
layer connected it's a good idea to turn it on by default.
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The IO port selection for MPC8544DS board:
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Many of the Blackfin board linker scripts are preprocessed, so make sure we
output the linker script into the build tree rather than the source tree.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure all .text sections get pulled in and the entry point is properly
referenced so they don't get discarded when linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In order to boot an LDR out of parallel flash, the ldr utility needs a few
flags to tell it to generate the right header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Initial support for Extreme Engineering Solutions XPedite5200 -
a MPC8548-based PMC single board computer.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Update X-ES Freescale boards to allow inbound PCI configuration
cycles when configured as agent/endpoint.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Apply changes from commit 44b4dbed to board/trab/memory.c, too.
Actually we'd need a major cleanup here - as it turns out,
board/trab/memory.c is more or less a verbatim copy of
post/drivers/memory.c ... but then, trab is EOL anyway,r
so this is not worth the effort.
Signed-off-by: Wolfgang Denk <wd@denx.de>
A value of BSC CS4 was wrong, Fixed it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes building U-Boot for CPCI405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
---
Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.
This change will go through microblaze custodian tree.
