2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-17 16:53:06 +00:00
Commit graph

12 commits

Author SHA1 Message Date
Stephen Warren
6dca554f23 ARM: tegra: fix ULPI PHY on Ventana and Seaboard
Commit ce02a71c23 "tegra: dts: Sync tegra20 device tree files with
Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure
that U-Boot code could handle this. In practice, various code is missing,
and various configuration options are not enabled, which causes U-Boot to
hang when attempting to initialize this USB port. This patch enables ULPI
PHY support on Ventana, and adds the required pinmux setup for the port to
operate. Note that Ventana is so similar to Seaboard that this change is
made in the Seaboard board file, which is shared with Ventana.

Seaboard also has the ULPI USB port wired up in hardware, although to an
internal port that often doesn't have anything attached to it. However,
the DT nodes for the USB controller and PHY had different status property
values, so the port was not initialized by U-Boot. Fix this inconsistency,
and enable the ULPI port, just like in the Linux kernel DT. This likewise
requires enabling ULPI support in the Seaboard defconfig.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:03 -07:00
Stephen Warren
002ddbffb6 ARM: tegra: fix USB controller aliases
Some boards have a different set of USB controllers enabled in DT than
the set referenced by /alias entries. This patch fixes that. For
example, this avoids the following message while booting on Ventana,
which is caused by the fact that the USB0 controller had no alias, and
defaulted to wanting a sequence number of 0, which was later explicitly
requested by the alias for USB controller 2.

USB2:   Device 'usb@c5008000': seq 0 is in use by 'usb@c5000000'

This didn't affect USB operation in any way though.

Related, there's no need for the USB controller aliases to have an order
that's different from the HW order, so re-order any aliases to match the
HW ordering. This has the benefit that since USB controller 0 is the only
one that supports device-mode in HW, and U-Boot only supports enabling
device move on controller 0, there's now good synergy in the ordering! For
Tegra20, that's not relevant at present since USB device mode doesn't work
correctly on that SoC, but it will save some head-scratching later.

This patch doesn't fix the colibri_t20 board, even though it has the same
issue, since Marcel already sent a patch for that.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Harmony and Ventana
2016-09-27 09:11:03 -07:00
Stephen Warren
67748a73b1 mmc: tegra: use correct alias for SDHCI/MMC nodes
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Simon Glass
ec5507707a video: tegra: Move to using simple-panel and pwm-backlight
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.

This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:

   - colibri
   - medcom-wide
   - paz00
   - tec

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
ce02a71c23 tegra: dts: Sync tegra20 device tree files with Linux
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Stephen Warren
54693cbdca video: tegra: refuse to bind to disabled dcs
This prevents the following boot-time message on any board where only the
first DC is in use, yet the DC's DT node is enabled:

stdio_add_devices: Video device failed (ret=-22)

(This happens on at least Harmony, Ventana, and likely any other Tegra20
board with display enabled other than Seaboard).

The Tegra DC's DT node represents a display controller. It may itself
drive an integrated RGB display output, or be used by some other display
controller such as HDMI. For this reason the DC node itself is not
enabled/disabled in DT; the DC itself is considered a shared resource, not
the final (board-specific) display output. The node should instantiate a
display output driver only if the rgb subnode is enabled. Other output
drivers are free to use the DC if they are enabled and their DT node
references the DC's DT node. Adapt the Tegra display drivers' bind()
routine to only bind to the DC's DT node if the RGB subnode is enabled.

Now that the display driver does the right thing, remove the workaround
for this issue from Seaboard's DT file.

Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
91c08afe66 tegra: video: Move LCD driver to use the DM PWM driver
Use the driver-model PWM driver in preference to the old code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:53 -07:00
Simon Glass
9e6866d3b6 tegra: video: Convert tegra20 LCD driver to driver model
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.

Boards which use this are fixed up, but only seaboard is tested.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:52 -07:00
Simon Glass
ee7d755a58 tegra: dts: Sync tegra20.dtsi with Linux v4.4
This file has changed quite a bit since it was set up. Sync it back with
Linux v4.4. Adjust the users slightly to cope with the changes:

- the host1x node is now called host1x@50000000
- we need a clocks node to provide the clk32k_in phandle
- active usb nodes need status = "okay"
- active i2c nodes need status = "okay"

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:51 -07:00
Simon Glass
2b2b50bc87 dm: tegra: dts: Use TEGRA_GPIO() macro for all GPIOs
This new method is much easier and matches the kernel.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Simon Glass
c369139234 tegra: dts: Add serial port details
Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.

The console alias needs to be set up to indicate which port is used for
the console.

Also add a binding file since this is missing.

Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 13:00:02 -06:00
Masahiro Yamada
5ab502cb89 dts: move device tree sources to arch/$(ARCH)/dts/
Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.

For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.

This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Renamed from board/nvidia/dts/tegra20-seaboard.dts (Browse further)