arch_lmb_reserve() protects U-Boot relocated code with stack not to be used
for image relocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze as Arm is using multiple memory banks which are read from DT
that's why there is a need to initialized LMB based on bd->bi_dram[].
Without this fix memory base/size is all the time 0 and image relocation is
not possible.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_SYS_BOOT_RAMDISK_HIGH is already defined in
arch/arm/include/asm/config.h:10:#define CONFIG_SYS_BOOT_RAMDISK_HIGH
that's why there is no reason to define it again in board file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
This patch assings the phynode pointer to the phydev node as it is needed
later in the corresponding phy driver to read phy properties from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes zynq_gpio_direction() to call driver specific
zynq_gpio_set_value function rather than top level gpio_set_value.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PSCI_RESET and EXPERT are not needed for mini configurations so remove
them to save space.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds default offset & sector size values for environment
variables to save in qspi/ospi flash for versal.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Phy setup should be done before dwc3 soft core reset as it is done
in linux & this fixes unreliable detection of usb cable on host side.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables 2 nand chips support for zynqmp mini nand
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Devicetree bindings are already specified in Linux kernel documentation.
Instead of maintaining same dt bindings in U-Boot doc specify path to dt
bindings in Linux kernel & documenting specific changes that are in U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The zynq_sdhci drivers depends on DM_MMC in Kconfig so no need to check for
DM_MMC in the driver so this patch removes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms have been moved to distro boot that's why remove the rest of
configurations to have unified boot flow.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Follow conventions and used {} around variables.
Fixes: 90e97ab31e ("arm: zynq: Define distro boot commnads for qspi, nand and nor")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are two typos in this command that's why it couldn't work properly.
This bootmode is almost unused from the beggining on this SoC.
Fixes: 90e97ab31e ("arm: zynq: Define distro boot commnads for qspi, nand and nor")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx Zynq SoC has two sdhci controllers but boot is only possible from
the first one. That's why there is a need to specify controller number.
mmc1 is supposed to be secondary boot device and should be also listed in
distribution boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch define init routine for generic phy driver and registers it
using phy_register as this generic phy driver also needs to be relocated
incase of manual reloc.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add zu48dr and zu49dr to the list of zynqmp devices. The zu48dr and zu49dr
are the new RFSoC silicons with id values of 0x7b and 0x7e.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reduces the console buffer size from 2048 to 1024, thus fixes
OCM overwriting issue.
Differences are in bss section as is shown from output:
xilinx_versal_mini: all -2056 bss -2048 text -8
u-boot: add: 0/0, grow: 0/-3 bytes: 0/-2056 (-2056)
function old new delta
cli_simple_run_command 340 332 -8
static.lastcommand 2049 1025 -1024
console_buffer 2049 1025 -1024
Better would be to use PPU RAM but this change is also aligned with changes
done in ZynqMP mini configurations.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP and Versal is using 2k that's why aligned all platform together to
be able to use the same scripts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Increase init ram size by 4K such that more stack space will be available
during initialization as the present stackspace is not sufficient if DEBUG
option is enabled and causes system hang. Increasing init ram size provides
sufficient stack space during init even if DEBUG enabled and solves the
hang issue.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option is disable in Xilinx tree for quite a long time that's why
let's disable it in mainline. If there is anybody who requires this options
then it should be moved to Kconfig first and should be removed from this
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes check for Versal platform
in gem driver as it now supports clock setting
through clock framework.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds clock driver support for Versal platform. The clock driver
queries and performs clock operations using PLM firmware by communicating
with it using SMC calls.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new versal compatible string to GEM driver for Versal
platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file in
DDR and execute it first incase of jtag bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates scriptaddr value to 512MB as having it at 32MB has high
chance of script corruption incase of bigger kernel.
Be aware that 512MB is used for SPL malloc area that's why images should be
loaded after SPL (the best after u-boot relocation).
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With the current boot script offset address in qspi is being overlaped
by BOOT.BIN as it is over 90MB with fpga included. So moving the script
offset address to end of flash after "bootenv" mtd partition. Here we
are considering qspi flash size >= 128Mbytes on versal and left
512Kbytes space to save boot.scr script.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new dfu usb distro boot command to look for bootscript
from dfu-util and runs it.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file
in DDR and execute it first incase of jtag bootmode.
This patch also updates scriptaddr to 512MB as there is high of script
corruption incase of bigger kernel image.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add simple ZynqMP firmware drive to populate child nodes under
zynqmp_firmware DT node.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to enable/disable OCM and TCM memory into MMU
table with corresponding memory attributes.
The same change was done for ZynqMP by commit 189bec47ab
("arm64: zynqmp: Provide a Kconfig option to define OCM and TCM in MMU")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code reads DT and setup MMU table based on memory node. This will ensure
that only DT needs to be changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
