As a first step toward converting this driver to the driver model, use
the ofnode abstraction to replace direct references to the FDT blob.
Using ofnode_read_u32_index removes an extra pair of loops and makes the
allwinner,rb property optional, matching the devicetree binding.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
NAND is always at function 2 on port C.
Pin lists and mux values were taken from the Linux drivers.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently NAND clock setup is done in board code, both in SPL and in
U-Boot proper. Add the NAND clocks/resets here so they can be used by
the "full" NAND driver once it is converted to the driver model.
The bit locations are copied from the Linux CCU drivers.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
add nvmxip_qspi driver under UCLASS_NVMXIP
The device associated with this driver is the parent of the blk#<id> device
nvmxip_qspi can be reused by other platforms. If the platform
has custom settings to apply before using the flash, then the platform
can provide its own parent driver belonging to UCLASS_NVMXIP and reuse
nvmxip-blk driver. The custom driver can be implemented like nvmxip_qspi in
addition to the platform custom settings.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
For more details please refer to doc/develop/driver-model/nvmxip_qspi.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
add block storage emulation for NVM XIP flash devices
Some paltforms such as Corstone-1000 need to see NVM XIP raw flash
as a block storage device with read only capability.
Here NVM flash devices are devices with addressable
memory (e.g: QSPI NOR flash).
The implementation is generic and can be used by different platforms.
Two drivers are provided as follows.
nvmxip-blk :
a generic block driver allowing to read from the XIP flash
nvmxip Uclass driver :
When a device is described in the DT and associated with
UCLASS_NVMXIP, the Uclass creates a block device and binds it with
the nvmxip-blk.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
The code has quite a few unnecessary brackets and comparisons to zero,
etc. Fix these up as well as some upper-case hex values and use of 0x in
printf() strings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Avoid the use of the function name in a few of the debug() calls, since
this causes a checkpatch warning. Convert all other calls too.
Use lower-case hex consistently.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix a longstanding bug where the LBA is calculated as the size of the
media instead of the number of blocks. This was perhaps not noticed
earlier since it prints the correct value first, before setting the wrong
value.
Drop the unnecessary blksz variable while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 68e6f221ed ("block: ide: Fix block read/write with driver model")
We only use one member of the ide_dev_desc[] array at a time and it does
not stick around outside ide_probe(). Use a single element instead.
Copy over the missing members of blk_desc at the same, since this was
missing from the previous code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 68e6f221ed ("block: ide: Fix block read/write with driver model")
Rather than having the caller fill some of this in, do it all in the
ide_ident() function, since it knows all the values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update ide_ident() to indicate whether it finds a device or not. Use
that to decide whether to create a block device for it, rather than
looking DEV_TYPE_UNKNOWN.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most of the code uses 'desc' as the variable name for a blk descriptor.
Change ide to do the same.
Tidy up some extra brackets and types while we are here.
Leave the code in ide_probe() alone since it is about to be refactored.
Signed-off-by: Simon Glass <sjg@chromium.org>
The two loops in this function operate on the same ide_dev_desc[] array.
Combine them to reduce duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that ide_probe() is the only caller of ide_init(), move all the code
into the probe function, so it is easier to refactor it.
Move ide_dev_desc[] into ide_probe() to, since it is the only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation adds this information in the block device's
probe() function, which is called in the blk_probe_or_unbind() in
ide_probe().
It is simpler to do this in ide_probe() itself, since the effect is the
same. This helps to consolidate use of ide_dev_desc[] which we would like
to remove.
Use strlcpy() to keep checkpatch happy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use IS_ENABLED() instead for all conditions. Add the 'lba48' flag into
struct blk_desc always, since it uses very little space. Use a bool so
the meaning is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Change the if() to remove extra brackets and check for the positive case
first, i.e. when a device is found. Exit the loop in that case, with the
retry logic in the 'else' part.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is hard to follow as it uses #ifdef in a strange way. Adjust
it to avoid the preprocessor. Drop the special return for the non-ATAPI
case since we can rely on tries becoming 0 and exiting the loop.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use a 'tries' variable which starts at the number of tries we want to do,
rather than a 'retries' one that stops at either 1 or 2. This will make it
easier to refactor the code to avoid the horrible #ifdefs
Signed-off-by: Simon Glass <sjg@chromium.org>
The use of atapi_read() was incorrect dropped. Fix this so that it will
be used when needed. Use a udevice for the first argument of atapi_read()
so it is consistent with ide_read().
This requires much of the ATAPI code to be brought out from behind the
existing #ifdef. It will still be removed by the compiler if it is not
needed.
Add an atapi flag to struct blk_desc so the information can be retained.
Fixes: 145df842b4 ("dm: ide: Add support for driver-model block devices")
Fixes: d0075059e4 ("ide: Drop non-DM code for BLK")
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These are not used from outside this file anymore. Make them static and
remove them from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the code does ide_init() as a separate operation, then calls
device_probe() to copy over the information. We can call ide_init() from
probe just as easily.
The only difference is that using 'ide init' twice will do nothing.
However it already fails to copy over the new data in that case, so the
effect is the same. For now, unbind the block devices and remove the IDE
device, which causes the bus to be probed again. Later patches will fix
this up fully, so that all blk_desc data is copied across.
Since ide_reset() is only called from ide_init(), there is no need to init
the ide_dev_desc[] array. This is already done at the end of ide_init() so
drop this code.
The call to uclass_first_device() is now within the probe() function of
the same device, so does nothing. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes virtio may rely on PCI, or at least that is what the
distro_bootcmd script suggests. Add this in.
Signed-off-by: Simon Glass <sjg@chromium.org>
If one leaves the CQSPI_REG_CMDCTRL in an unclean state this may cause
issues in future command reads. This issue came to light when some flash
reads in STIG mode were coming back dirty.
Co-developed-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
OSPI controller supports all types of op variants in STIG mode,
only limitation being that the data payload should be less than
8 bytes when not using memory banks.
STIG mode is more stable for operations that send small data
payload and is more efficient than using DMA for few bytes of
memory accesses. It overcomes the limitation of minimum 4 bytes
read from flash into RAM seen in DAC mode.
Use STIG mode for all read and write operations that require
data input/output of less than 8 bytes from the flash, and thereby
support all four phases, cmd/address/dummy/data, through OSPI STIG.
Also, remove the reorder address chunk in apb_command_write since we now
setup ADDR BIT field that does the same job in a cleaner way.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
buswidth and dtr fields in spi_mem_op are only valid when the
corresponding spi_mem_op phase has a non-zero length. For example,
SPI NAND core doesn't set buswidth when using SPI_MEM_OP_NO_ADDR
phase.
Fix the dtr checks in set_protocol() to ignore empty spi_mem_op
phases, as checking for dtr field in empty phase will result in
false negatives.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds fixups for s25fs512s to address the following issues
from reading SFDP:
- Non-uniform sectors by factory default. The setting needs to be
checked and assign erase hook as needed.
- Page size is wrongly advertised in SFDP.
- READ_1_1_2 (3Bh/3Ch), READ_1_1_4 (6Bh/6Ch), and PP_1_1_4 (32h/34h)
are not supported.
- Bank Address Register (BAR) is not supported.
In addition, volatile version of Quad Enable is used for safety.
Based on patch by Takahiro Kuwano with s25fs_s_post_bfpt_fixup() updated
to use 4-byte address commands instead of extended address mode and the
page_size is fixed to 256
For future use, manufacturer code should be moved out from framework
code as same as in Linux.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Family of panels used by HTC in One X. Though were used variants
at least from 3 vendors, this driver provides generic support for
all of them.
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X T30 Sony
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30 Sharp
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DC based PWM backlight is found on some T20 and T30 devices
(HTC One X). This backlight is controlled by Tegra DC and
is adjustable by the DC PM0 or PM1 signal.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # HTC One X T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver adds support for panels with Renesas R69328 IC
Currently supported compatible is:
- jdi,dx12d100vm0eaa
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
R61307 is liquid crystal driver for high-definition
amorphous silicon (a-Si) panels and is ideal for
tablets and smartphones.
Supported compatibles are:
- koe,tx13d100vm0eaa
- hitachi,tx13d100vm0eaa
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SSD2825 is an innovative and cost-effective MIPI Bridge Chip solution
targeting high resolution smartphones. It can convert 24bit RGB
interface into 4-lane MIPI-DSI interface to drive extremely high
resolution display modules of up to 800 x 1366, while supporting AMOLED,
a-si LCD or LTPS advanced panel technologies for smartphone applications.
Bridge is wrapped in panel uClass model for wider compatibility.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This is basic lm3533 driver only with bank A and backlight cell
support.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By the time we jump to the err label, count represents the number of
gpios we've successfully requested. So by subtracting one, we fail to
free the most recently requested.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xen core_init() is calling HVC which should be called from EL1 level that's
why do Xen initialization only when U-Boot runs in EL1.
Signed-off-by: Michal Simek <michal.simek@amd.com>
The non DM code path already would enable pci bus mastering. Do the
same for the DM code path.
Fixes AHCI problems I am seeing on an Intel Apollolake device.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[trini: Use ahci_dev not dev in the calls]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add weak function psci_sysreset_get_status for platform to define
their own reset status with CONFIG_SYSRESET enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
XEN config can be enabled by other platforms (even it doesn't need to make
sense) that's why fix dependencies. XEN (xenbus.c) requires sscanf (also
pvblock needs it). And PVBLOCK is inside drivers/xen folder which requires
XEN to be enabled.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When building with clang, it notes that sdinfo may be unused
uninitialized in some cases. This appears to be true from reading the
code, and we can simply set the variable to zero to start with and be as
correct as before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
If rev is equal to the array size, we'll access the array
one-past-the-end.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Bryan Brattlof <bb@ti.com>
When building with clang, the compiler compains with
drivers/spi/spi-synquacer.c:212:11: warning: variable 'bus_width' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
else if (priv->mode & SPI_TX_OCTAL)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-synquacer.c:276:11: note: uninitialized use occurs here
val |= ((bus_width >> 1) << BUS_WIDTH);
^~~~~~~~~
drivers/spi/spi-synquacer.c:212:7: note: remove the 'if' if its condition is always true
else if (priv->mode & SPI_TX_OCTAL)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-synquacer.c:189:25: note: initialize the variable 'bus_width' to silence this warning
So initialize bus_width to 1 and add a warning if none of the configured
modes matches
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
NPCM7xx/NPCM8xx default is boot from flash.
removed set clock feature due to reliability and security.
the clock will set by bootblock or tip.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The .supports_op() callback function returns true by default after
performing driver-specific checks. Therefore the driver cannot apply
the buswidth in devicetree.
Call spi_mem_default_supports_op() helper to handle the buswidth
in devicetree.
Fixes: 358f803ae2 ("spi: Add Socionext F_OSPI SPI flash controller driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
in spi_mem_dtr_supports_op we have a check for allowing only even number
of bytes to be r/w. Odd bytes writing can be a concern while writing
data to a flash for example because 8 DTR mode doesn't support it.
However, reading ODD Bytes even though may not be physically possible
we can still allow for it because it will not have serious implications
on any critical registers being overwritten since they are just reads.
Cc: Vaishnav Achath <vaishnav.a@ti.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This should have been op->data.buswidth instead as we check for octal
bus width for the data related ops
Also add explanation for why there is checks for 8D even data bytes
Cc: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for CHIP_ERASE opcode 0xc7 . This is useful in case the
entire SPI NOR is supposed to be erase at once, as is it considerably
faster than 4k sector erase and even slightly faster than 64k block
erase. The spi_nor_erase_chip() implementation is adapted from Linux
6.1.y as of commit 7d54cb2c26dad ("Linux 6.1.14") . The chip erase is
only used in case the entire MTD device is being erased, and the chip
does support this functionality.
Timing figures from W25Q128JW:
16 MiB erase using 4kiB sector erase opcode 0x20 ... 107.5s
16 MiB erase using 64kiB block erase opcode 0xd8 ... 39.1s
16 MiB erase using chip erase opcode 0xc7 .......... 38.7s
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Devices advertising the VIRTIO_F_IOMMU_PLATFORM feature require
platform-specific handling to configure their DMA transactions.
When handling virtio descriptors for such a device, use bounce
buffers to ensure that the underlying buffers are always aligned
to and padded to PAGE_SIZE in preparation for platform specific
handling at page granularity.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: 1eff171e61
Reviewed-by: Simon Glass <sjg@chromium.org>
In preparation for bouncing virtio data for devices advertising the
VIRTIO_F_IOMMU_PLATFORM feature, allocate an array of bounce buffer
structures in the vring, one per descriptor.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: 3e052749e7
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the attach and detach logic for manipulating vring descriptors
out into their own functions so that we can later extend these to
bounce the data for devices with VIRTIO_F_IOMMU_PLATFORM set.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: f73258a4bf
Reviewed-by: Simon Glass <sjg@chromium.org>
In preparation for explicit bouncing of virtqueue pages for devices
advertising the VIRTIO_F_IOMMU_PLATFORM feature, introduce a couple
of wrappers around virtqueue allocation and freeing operations,
ensuring that buffers are handled in terms of page-size units.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: b4bb5227d4
Reviewed-by: Simon Glass <sjg@chromium.org>
The pages backing the virtqueues for virtio PCI devices are not freed
on reset, despite the virtqueue structure being freed as part of the
driver '->priv_auto' destruction at ->remove() time.
Call virtio_pci_del_vqs() from virtio_pci_reset() to free the virtqueue
pages before freeing the virtqueue structure itself.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: 5ed54ccd83
Reviewed-by: Simon Glass <sjg@chromium.org>
If we detect the VIRTIO_F_IOMMU_PLATFORM transport feature for a device,
then expose it in the device features.
Signed-off-by: Will Deacon <willdeacon@google.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Link: 9693bd26bf
Reviewed-by: Simon Glass <sjg@chromium.org>
To support video driver at SPL use CONFIG_IS_ENABLED and CONFIG_VAL,
which checks for stage specific configs and thus enables video support
at respective stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
To enable TIDSS driver only at SPL stage add rule to compile the TIDSS
video driver.
CONFIG_$(SPL_)VIDEO_TIDSS will compile tidss_drv, at SPL only if
CONFIG_SPL_VIDEO_TIDSS is defined and at u-boot proper if
CONFIG_VIDEO_TIDSS is defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To enable video driver at SPL, need to compile video-uclass,
vidconsole-uclass, backlight-uclass, panel-uclass, simple-panel, add
rules to compile them at SPL and u-boot proper. To support
splash_display at SPL, need to compile video-bmp, add rule to compile at
SPL and u-boot proper.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Compile video driver at SPL using CONFIG_SPL_VIDEO.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Add Kconfigs which enable the video driver and splash screen at SPL
stage only and not at u-boot proper. The existing Kconfigs from u-boot
proper were not used to make SPL splash screen independent to them.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Configuring master firewalls require the power of the cluster to be
enabled before configuring them, change the load of rproc to configure
the gtc clocks and start the cluster along with configuring the boot
vector.
The start of rproc will only start the core.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The K3 JTAG and SoC ID information is already stored in the K3 arch
hardware file, include that and use its definitions here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
- watchdog: arm_smc_wdt: add watchdog support (Lionel)
- watchdog: ftwdt010: return a previously deleted driver now ported to
DM (Sergei)
- watchdog: Add a watchdog driver for Raspberry Pi boards (Etienne)
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm]
Link: https://lore.kernel.org/all/20230407134008.1939717-3-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
It will be replaced by a more recent version which contains fixes for
tests run by Tom Rini.
This reverts commit ff33d3c87c.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Using DMA to load TF-A into SRAM fails when booting from eMMC on RK3588.
## Checking hash(es) for Image atf-3 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-3' image node
spl_load_simple_fit: can't load image loadables index 2 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
Fix this by using PIO mode in SPL and limit the number of blocks used in
a single read command to avoid triggering Data End Bit Error interrupt.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip emmc devices have a similar issue to Rockchip dwmmc devices,
where performing DMA to SRAM later causes issues with suspend/resume.
Allow us to toggle SDMA in SPL for sdhci similar to ADMA support, so we
can ensure DMA is not used when loading the SRAM code.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[jonas@kwiboo.se: add Kconfig default value and fix ADMA typo]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The device tree sdhci node reference the TMCLK_EMMC clock, add limited
support this clock to rk3588 cru driver. Fixes probe of sdhci driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for RK3588 to the rockchip sdhci driver.
Use driver data to handle differences between RK3568 and RK3588:
- Set "Receive original clock source is auto gating" for RK3588.
- Set "Receive clock source is no-inverted" only on RK3568 and "Transmit
clock source is invertion of original clock input" for RK3588.
- Use different txclk_tapnum for HS400 modes on RK3588.
- Configure the CMDOUT reg for HS400 modes for RK3588.
This is based on the mainline linux and vendor kernel driver and have
successfully been tested with rock5b-rk3588_defconfig and
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_SPEED_MODE_SET=y
using the following command to switch mode and then read 512 MiB of data
from eMMC into memory,
=> mmc dev 0 0 <mode> && mmc info && mmc read 10000000 2000 10000
for each of the modes below.
0 = MMC legacy
1 = MMC High Speed (26MHz)
3 = MMC High Speed (52MHz)
4 = MMC DDR52 (52MHz)
10 = HS200 (200MHz)
11 = HS400 (200MHz)
12 = HS400ES (200MHz)
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust tap number for transmit clock, tap number and delay number for
strobe input to fix HS400 modes on RK3568.
New values have been picked from vendor kernel and u-boot and have
successfully been tested with rock-3a-rk3568_defconfig and
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_SPEED_MODE_SET=y
using the following command to switch mode and then read 512 MiB of data
from eMMC into memory,
=> mmc dev 0 0 <mode> && mmc info && mmc read 10000000 2000 10000
for each of the modes below.
0 = MMC legacy
1 = MMC High Speed (26MHz)
3 = MMC High Speed (52MHz)
4 = MMC DDR52 (52MHz)
10 = HS200 (200MHz)
11 = HS400 (200MHz)
12 = HS400ES (200MHz)
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This rearrange and remove duplicate defines to make the code cleaner.
There is no need to read vendor area1 and use an offset each time, it is
easier and clearer to just use the reg offset defined in TRM, same as
the other vendor regs.
This also removes use of the misspelled const for the RK3588 CMDOUT reg,
it will be re-added when support for RK3588 is introduced.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove empty implementations of get_phy and set_enhanced_strobe ops.
Change driver set_enhanced_strobe to return 0 in order to allow missing
implementation of the ops.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor set_ios_post ops to correctly set UHS Speed Select field values
according to TRM. Also set or unset Enhanced Strobe Enable bit and
eMMC Card present bit in set_ios_post, the Enhanced Strobe Enable bit
was never unset after switching to HS400ES mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Check return value from mmc_send_cmd and clear HOST_CONTROL2 when there
is an error. Also skip enable of interrupt signaling and remove a delay,
a delay is already happening in sdhci_send_command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to configure clock and DLL in set_clock and config_dll ops
instead of in the set_ios_post ops.
With this change the output clock is turned off while configuring DLL
parameters, according to the design recommendations.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the set_clock and config_dll sdhci_ops. Use of these ops
will allow configuration of DLL while the output clock is disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unneeded emmc_phy_init now that the no-inverter flag is
handled correctly after commit 2321a991bb ("rockchip: sdhci: rk3568:
bypass DLL when clk <= 52 MHz").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device private data is misused in rockchip_sdhci_of_to_plat and
rockchip_sdhci_execute_tuning.
In these functions dev_get_priv is assigned to struct sdhci_host:
struct sdhci_host *host = dev_get_priv(dev);
Instead, the sdhci host should refer to host in struct rockchip_sdhc:
struct rockchip_sdhc *priv = dev_get_priv(dev);
struct sdhci_host *host = &priv->host;
Because host is the first member in struct rockchip_sdhc this is not a
real problem, lets fix it anyway and also use priv name consistently.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set correct UHS Mode Select field value for UHS SDR25 (50MHz) mode.
Fixes: d1c0a2200a ("mmc: sdhci: Add support for HOST_CONTROL2 and setting UHS timings")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set High Speed Enable bit for MMC High Speed (52MHz) mode.
Fixes: f12341a952 ("mmc: sdhci: Fix HISPD bit handling")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds support for the TRNG found in the RK3588 SoC to the
rockchip_rng driver so that it can be used for things such as
seeding randomness to Linux.
Changes in V3:
- Moved notes from commit to cover letter.
- Added Reviewed-By tag.
Changes in V2:
- Modified Kconfig to note that the Rockchip RNG driver supports all
versions of the hardware (v1, v2, and the trng in the rk3588).
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A RK3568 device tree pmic node can reference the I2S1_MCLKOUT_TX clock
in assigned-clocks, add dummy support to set parent of this clock to the
rk3568 cru driver.
Fixes probe of pmic driver and missing regulators on affected boards,
rk3568-evb and rk3568-rock-3a.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
IO mux selection is not working correctly for all pins. Sync mux route
data from linux to add any missing and update wrong trigger pins to fix
this. Also apply the pull-up fix needed for GPIO0 D3-D6.
Fixes: 1977d746aa ("rockchip: rk3568: add rk3568 pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Booting from sdmmc on RK3588 currently works because of a workaround in
the device tree, clocks are reordered so that the driver use ciu-sample
instead of ciu, and the BootRom initializes sdmmc clocks before SPL is
loaded into DRAM.
The sdmmc clocks are normally controlled by TF-A using SCMI. However,
there is a need to control these clocks in SPL, before TF-A has started.
This adds a rk3588_scru driver to control the sdmmc clocks in SPL before
TF-A has started, using scru regs. It also adds a small glue driver to
bind the scmi clock node to the rk3588_scru driver in SPL.
Fixes: 7a474df740 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Building U-Boot SPL with CLK_SCMI and SCMI_FIRMWARE Kconfig options
enabled and SPL_FIRMWARE disabled result in the following error.
drivers/clk/clk_scmi.o: in function `scmi_clk_gate':
drivers/clk/clk_scmi.c:84: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:88: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_get_rate':
drivers/clk/clk_scmi.c:113: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:117: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_set_rate':
drivers/clk/clk_scmi.c:139: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:143: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_probe':
drivers/clk/clk_scmi.c:157: undefined reference to `devm_scmi_of_get_channel'
make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make: *** [Makefile:2043: spl/u-boot-spl] Error 2
Add Kconfig option so that CLK_SCMI can be disabled in SPL to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for DSI Host controller on Rockchip RK3568. This driver
is heavily based on the Rockchip dw_mipi_dsi_rockchip.c driver in
Linux and the stm32_dsi.c driver in U-Boot. It should be easy to add
support for other SoCs as the only missing component from the mainline
driver is setting the VOP big or VOP little (which the rk3568 does
not have).
Driver was tested for use in sending commands to a DSI panel in order
to obtain the panel ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the Innosilicon DSI-DPHY driver for Rockchip SOCs.
The driver was ported from Linux and tested on a Rockchip RK3566
based device to query the panel ID via a DSI command.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For 2 GB LPDDR4 single-rank RAM with 16 rows, the Rockchip ddr init bin
prints:
"Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB"
U-Boot TPL prints:
"BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB"
Add missing high row detection so that U-Boot TPL prints Row=16, same as
the Rockchip ddr init bin:
"BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB"
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GPIO V2 controller on RK3568 and RK3588 works very similar to
prior generation, main difference is the use of a write mask in the
upper 16 bits and register address offset have changed.
GPIO_VER_ID is a new register at 0x0078 that is used to determine when
the driver should use new or old register offsets and values. Earlier
generation return 0x0 from this offset.
Refactor code and add support for the GPIO V2 controller used in RK3568
and RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current divider to calculate the bank ID can change.
Given the Rockchip TRM not all gpio-banks have 32 pins per bank.
The "gpio-ranges" syntax allows multiple items with variable number
of pins. Use a constant ROCKCHIP_GPIOS_PER_BANK as fixed divider.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 pwm nodes synced from Linux make use of PCLK_RKPWM
instead of PCLK_PWM. They have the same pclk_cpu parent,
so add PCLK_RKPWM to rk3288_clk_get_rate().
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the current rk3288.dtsi file the compatible string for
the DisplayPort(DP) node ends with "edp". The string in the
binding ends with "dp" which conflicts with "cdn-dp" as a
search term. Add "rk3288-dp" as compare string to select
vop_id.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Rockchip rk3588 variant of pinctrl.
The driver is adapted from the Linux driver.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
[eugen.hristev@collabora.com:
port to latest U-boot, bring more changes from Linux
use translated pull values table]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
mmc->tran_speed is max clock, but currently rk3568_sdhci_set_ios_post
uses it if its != 0, regardless of mmc->clock value, and it breaks
eMMC controller.
Without this patch 'mmc dev 0; mmc dev 1; mmc dev 0' is enough for
breaking eMMC, since first initialization sets mmc->mmc_tran speed
to non-zero value (26MHz in my case), and on subsequent re-init when
mmc layer asks for 400KHz it sets 26MHz instead.
Fix it by using MAX(mmc->tran_speed, mmc->clock)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add driver for StarFive JH7110 to support ddr initialization in SPL.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add a DM reset driver for StarFive JH7110 SoC.
Note that the register base address of reset controller is the
same with the clock controller. Therefore, there is no device
tree node alone for reset driver.It binds device node in
the clock driver
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
This adds support for the StarFive JH7110 SoC which also
feature this SiFive cache controller.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the EDO mode support from as the FMC2 controller does not
support the feature.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently, in stm32_qspi_claim_bus(), QSPI_CR and QSPI_DCR registers
are saved in stm32_ospi_flash struct on first flash memory initialization
and restored on each flash accesses.
As the logic of spi-uclass.c changed since 'commit 741280e9ac
("spi: spi-uclass: Fix spi_claim_bus() speed/mode setup logic")'
set_speed() and set_mode() callbacks are called systematically when bus
speed or bus mode need to be updated, QSPI_CR and QSPI_DCR registers are
set accordingly.
So stm32_qspi_claim_bus() can be updated by removing QSPI_CR and QSPI_DCR
save/restore code and struct stm32_ospi_flash can be removed as well.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
For debug purpose, it should be useful to indicate the slew rate for
each pins.
Add ospeed register information for pins which are configured in
either alternate function or gpio output.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Implement a ARM SMCCC based driver that allow to use
a secure watchdog on the platform.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ftwdt010 watchdog driver was deleted by
commit 11232139e3 ("nds32: Remove the architecture")
Return it to the codebase in a DM compatible form. Enable it in
sandbox_defconfig to test compilability.
Another platform using ftwdt010 will be submitted later.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver supports the bcm2835 watchdog found on
Raspberry Pi boards.
It is derived from the Linux driver and was tested
on two Raspberry Pi board versions (B+ and 3B+).
Signed-off-by: Etienne Dublé <etienne.duble@imag.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----
iQJYBAABCgBCFiEE6GOTDNYiFygVXvMmQBtB6IWRjvEFAmQ9ALMkHGRhcmlvLmJp
bmFjY2hpQGFtYXJ1bGFzb2x1dGlvbnMuY29tAAoJEEAbQeiFkY7x6YMP/3vW6t7v
R0y3pGS0CcZhOtxLKH2Z5KbC6qoFmkK40vqvrKyUX1m4haJ+4A6BJR/rvdTCNftP
2ezpSF5SV7ZnG6+DIuY3Zvh7Jr9+ApuMmsm2vPeg8bv8gevzq3dHMk8msZb3P9+c
YX0FOpukZcJiYI9p2d+AFBLS2ETvfOYNhcfGu9PP1LdlChu1VL5BTwxmiKPuNf7D
6Rte3he0JubiLGp3CnLnj+o2l2OVrj+Kokv+jBCVVDtaVujD8tUCT+FJ/8FrXgFS
S/IOxV1DwhaxGHEjzM6ozq94b2lKB1v9PvapmveQSRmY+O01Q108uFUxMw5G6RyS
tEzoqdTk6u5Gzv/arsbXNSPe6i41QY454NqA5tOdUYprMQKM8k/P+ow9c5r4VRMH
YybBqYMAYs/9qmhBBfHhMnwEpzpHxBVTBTWtdqEIP85FcDgDV6HOs3imx05VnMe4
jfUBja5I0rzo9i7tvOhOOr4KTA1Qdg4xGTEm2nvKXHoIrGm3pC4wY54Q1F2UNm1b
osyqUh9pHqlgy+/8VPsUmu8zoewH/j4tGl1JRhYPd2QmYPlI7lDkhRtOBGOzBDAF
xvUQd5F2sYw6bDe7kiUfoX37Uy8cDupAETEYLpnGqG2/sLDo5p/VPNEiETAbfCmV
yVTDYvljxy/l3sqTUqbmkYS7V64UUc8tn0ql
=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
This patch adds Ethernet Switch support that found on R-Car S4
(r8a779f0) SoC. This is extracted from multiple patches from
downstream BSP, with additional rework of the network device
registration.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Marek: Rework the driver to support all ports via subdrivers.
Split the driver up, add generic PHY framework support.
Generic code clean ups.]
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add Renesas Ethernet SERDES driver for R-Car S4-8 (r8a779f0).
The datasheet describes initialization procedure without any information
about registers' name/bits. So, this is all black magic to initialize
the hardware. Especially, all channels should be initialized at once.
This driver is imported and adjusted from Linux 6.3-rc1 commit:
50133cd3e8dd1 ("phy: renesas: r8a779f0-eth-serdes: Remove retry code in .init()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use IS_ENABLED() instead of CONFIG_IS_ENABLED() to check for CONFIG_
option which is identical across all of U-Boot and xPL builds.
Fixes: 2769ddc99f ("mmc: tmio: Replace ifdeffery with IS_ENABLED/CONFIG_IS_ENABLED macros")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
octeontx_bch_devices and octeontx_pci_nand_deferred_devices are only
referenced in the files where they are defined. Make them static.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230405143837.785082-1-bmeng@tinylab.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308214231.378013-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308212851.370939-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
- DDR Training sequence happens very fast. The speedup in boot time is
negligible by skipping the training sequence during 2nd boot or after.
So remove the check and skip.
- This change improves the robustness of DDR training. If u-boot crashed
during DDR training, the training could be left in a limbo state, where
the BootROM has recorded that it is already in a 2nd boot. The training
must be repeated in this scenario to get out of this limbo state, but due
to the check it cannot be performed.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that all differences in functionality are covered by individual
flags, remove the enumeration of SoC variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.
This change provides two benefits beyond the simplification:
- R40 boards now respect the RX delays from the devicetree
- This resolves a warning on architectures where readl/writel
expect the address to have a pointer type, not phys_addr_t.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, EMAC variants are distinguished by their identity, but this
gets unwieldy as more overlapping variants are added. Add a structure so
we can describe the individual feature differences between the variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The HDMI PHY depends on the HVCC supply being enabled. So far we have
relied on it being enabled by an earlier firmware stage (SPL or TF-A).
Attempt to enable the regulator here, so we can remove that dependency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This abstracts away the CCU register layout, which is necessary for
supporting new SoCs like H6 with a reorganized CCU. One of the resets is
referenced from the PHY node instead of the controller node, so it will
have to wait until the PHY code is factored out to a separate driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This driver is actually used for powerpc and m68k/ColdFire.
On ColdFire SoC's, interrupt flag get not set if IIEN flag (mbcr bit6,
interrupt enabled) is not set appropriately before each transfert.
As a result, the transfert hangs forever waiting for IIEN.
This patch set IIEN before each transfert, while considering this fix
as not harming powerpc arch.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
The IS_ENABLED, which does not consider SPL build, should be replaced
by CONFIG_IS_ENABLED.
For the case that we only enable DM CLK for u-boot but not in SPL, the
IS_ENABLED(CONFIG_CLK) still returns true, then cause clock failure.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current code use dm_gpio_get_value() to get SDA and SCL value, and the
value depends on whether DTS file config the GPIO_ACTIVE_LOW. In ususal
case for i2c GPIO, DTS need to set GPIO_ACTIVE_LOW for SCL/SDA pins. So
here the logic is not correct.
And we must not use GPIOD_ACTIVE_LOW in client code include the
dm_gpio_set_dir_flags(), it is DTS's responsibility for this flag. So
remove GPIOD_ACTIVE_LOW here.
Fixes: aa54192d4a ("dm: i2c: implement gpio-based I2C deblock")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Alexander Kochetkov <al.kochet@gmail.com <mailto:al.kochet@gmail.com>>
This code first figures out if there is an i2c,speeds property, if so
its size in u32s, and then reads the value into the local speeds[]
array. Both 'size' and 'speeds' are completely unused thereafter.
It's not at all clear what this is supposed to do. Of course, it could
be seen as a sanity check that the DT node does have an i2c,speeds
property with an appropriate number of elements, but for that one
wouldn't actually need to read it into speeds[]. Also, I can't find
anywhere else in the U-Boot code which makes use of values from that
property (this is is the only C code referencing "i2c,speeds"), so it
seems pointless to insist that it's there.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
All build targets using this driver already use DM_MMC. So let's depend
this driver on this Kconfig symbol and remove the non-DM driver part.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
CONFIG_MMC_SDHCI_IO_ACCESSORS is not supported and/or used by this
driver so let's remove these unused parts completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
