Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for MMC. Remove the old mmc init code, which
is no longer used, from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for AHCI. Remove the old, now unused, sata
init code from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB. But it missed to enable driver
model support for keyboards. As a result, USB keyboards do no longer
work.
Fix this by enabling driver model support for keyboards.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We are going to be using check_time() on more than the mx53ppd, move this
function to a common location.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
There is an #ifdef and #endif with nothing in between. This patch simply
removes this dead/useless code.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.
It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.
Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
"ethernet" node fix-up for device tree happens before Linux boot.
There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabled
So provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FLIS IP since now gets its own ACPI ID.
Drop PRP0001 workaround in favour of official ACPI HID.
Corresponding kernel commit dabd4bc6de2b
pinctrl: intel: merrifield: Introduce ACPI device table
in the pin control subsystem tree [1] targeting v4.16.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=dabd4bc6de2b
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When adding a partition, set the logical_partition member in the media
structure as mandated by the UEFI spec.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This spi-nor is 4Mbit/512KB
Fixes: b4fbcbc5a5 ("mtd/spi: add support for is25lq040b")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now FASTBOOT_FLASH is auto select for sunxi platform,
so drop explicit addition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
and loading Image out of FIT image.
Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When booting a itb file with a Ramdisk on a imx6 based
board, U-Boot drops the warning:
Loading Kernel Image ... OK
Loading Ramdisk to 4ecf1000, end 4ef8b11f ... \
CACHE: Misaligned operation at range [4ecf1000, 4ef8b11f]
Fix it!
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Ayoub Zaki <hs@denx.de>
Use dfu_alt_info_emmc variable from include/environment/ti/dfu.h file.
It was probably overlooked when extracting DFU variables to mentioned
file.
This patch fixes DFU on BeagleBone Black, so that we can use commands
like ones below to upgrade various images on eMMC:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> dfu 0 mmc 1
$ dfu-util -D MLO -a MLO.raw
$ dfu-util -D u-boot.img -a u-boot.img.raw
Without this patch, the user is forced to assign the value to
dfu_alt_info_emmc manually, which contradicts with instructions [1].
[1] http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User%27s_Guide
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch is ported from the Linux patch posted at [1] and applied to
net tree as commit f1e2400a80ff.
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
[1] https://lkml.kernel.org/r/20171208110811.30789-1-jbrunet@baylibre.com
Fixes: 8995a96d1d ("net: phy: Add Amlogic Meson GXL Internal PHY support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Using writel causes a "Synchronous Abort". Invert the arguments.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlo3tMgACgkQykllyylKDCFQvQCfeFgaC/95gx9orLrHxpDx7s46
wwYAmwSoXn6hc9bEzgKIppQHblzfqGU6
=mscK
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Signed-off-by: York Sun <york.sun@nxp.com>
Rockchip release bl31.elf file for armv8 SoCs like rk3399, rk3328,
the elf have more than one section, we need to decode it first and
packed them into u-boot.itb with its file. This script is to generate
the its script.
Need default bl31.elf in root directory of U-Boot source and dtb
as parameter.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable SPL_FIT_GENERATOR with path for it.
With this patch you can get u-boot.itb for rk3399-firefly with:
> make u-boot.itb
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we support ATF in SPL and add script for it, let's make the
document up to date.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Only rk3399 atf need ROCKCHIP_SPL_RESERVE_IRAM. This commit updates
its default setting to 0 so that other SoCs do not need to define it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.
The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.
Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After adding our small zynq uboot which has hush parser off same
variable tests start to failed. Use quotes only when hush is enabled.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Access the timestamp ref ctrl register only if runinng
at el3 level otherwise just return. This change fixes
the issue when CRL APB is marked as secure and accessing
when not in el3 causes exception.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Check all return values from file functions.
In case of negative return exit immediately.
Also change fsize return value which can't be negative.
Reported-by: Coverity (CID: 23276, 23304, 169357)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont use 4K sector erase by default, Disabling this
would use 64K sector erase and decreases erase time.
Also disabled by the fact that UBIFS and JFFS2 won't work
with 4K sector erase.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling all spi flashes because some of these boards can have different
flashes compared to public version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adds ENV_SIZE and ENV_OFFSET configuration items for
ARCH_ROCKCHIP, but keeps these non-visible (i.e. not prompt is given).
With these new items present, the configuration from the header files
is moved to Kconfig.
Keeping these non-visible is necessary to have the possibility to
select new default values if CONFIG_IS_IN_* is changed (interactively
or with oldconfig). Otherwise it will always be set to a previous
value if used with a prompt. As an example if we do a defconfig with
CONFIG_IS_IN_MMC and change it to CONFIG_IS_IN_SPI_FLASH via
menuconfig, ENV_SIZE and ENV_OFFSET will not be changed to the correct
values as defconfig will already have set them to the default values
of CONFIG_IS_IN_MMC in .config.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A few fixes for 2018.01:
- Compile fix with helloworld example
- DP match fix (fixes FreeBSD loader and grub on block storage)
- More DP fixes for SD, block
- Fix use-after-free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tDFo
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-v2018.01' of git://github.com/agraf/u-boot
Patch queue for efi - 2017-12-17
A few fixes for 2018.01:
- Compile fix with helloworld example
- DP match fix (fixes FreeBSD loader and grub on block storage)
- More DP fixes for SD, block
- Fix use-after-free
The PCIe reset signal is connected to GPIO4_C6 on the Puma
module. This pin is supplied by 1.8V, but the default iodomain
setting is 3.0V and in this situation the pin is unable to go
high.
Linux assumes that this signal works in early boot
as PCIe is probed before loading the iodomain driver.
Make PCIe work in Linux by setting the gpio4cd iodomain to 1.8V.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
User do not need to access the reserved part in system, remove them
from partition table.
Rename atf to trust as generic name for armv7 do not use ATF.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a description for dp_part_fill().
Reword a comment in the function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When converting device nodes and paths to text we should
stick to the UEFI spec.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
According to the UEFI spec the numbering of partitions has to
start with 1.
Partion number 0 is reserved for the optional device path for
the complete block device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
