Commit graph

47 commits

Author SHA1 Message Date
Nishanth Menon
cdef0b3f3a ARM: OMAP3: rx51: Enable workaround for ARM errata 454179, 430973, 621766
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.

While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:33 -04:00
Nishanth Menon
c6f90e1418 ARM: OMAP3: Enable workaround for ARM errata 454179, 430973, 621766
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:24 -04:00
Nishanth Menon
49ec949091 ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1
omap_smc1 is now generic enough to remove duplicate
omap3_gp_romcode_call logic that omap3 introduced.

As part of this change, move to using the generic lowlevel_init.S for
omap3 as well.

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:00 -04:00
Ash Charles
b050898efa omap: gpmc: 'nandecc sw' can use HAM1 or BCH8
The 'nandecc sw' command selects a software-based error correction
algorithm.  By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm.  Allow a user to be specific e.g.
 # nandecc sw <hamming|bch8>
where 'hamming' is still the default.

Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
      to a hardware-based ECC scheme---a little strange when the user
      has requested 'sw' ECC.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
2015-03-05 20:49:43 -05:00
Simon Glass
7ae8350f67 ti: armv7: Move SPL SDRAM init to the right place, drop unused CONFIG_SPL_STACK
Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f().  Adjust the
code paths in these cases to be correct.  In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment).  In these cases switch to CONFIG_SPL_STACK_R.  In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM.  In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-03-04 14:55:04 -05:00
Tom Rini
a6b541b090 TI ARMv7: Don't use GD before crt0.S has set it
Prior to this change we set the gd pointer early so that we can store
data in it.  This becomes problematic for DM changes as well as being
odd in general.  Re-work the code paths so that we don't need to set the
gd pointer so early and instead can rely upon the normal setting of it.

In order to do this we do need to move certain calls from s_init into
spl_board_init(), mainly preloader_console_init and
save_omap_boot_params.

Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM,
OMAP5 uEVM, DRA7xx EVM
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-01-16 14:52:52 -05:00
Guillaume GARDET
205b4f33cf Rename some defines containing FAT in their name to be filesystem generic
Rename some defines containing FAT in their name to be filesystem generic:
MMCSD_MODE_FAT => MMCSD_MODE_FS
CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
2014-10-27 11:04:01 -04:00
Tom Rini
84a6df09c7 Merge git://git.denx.de/u-boot-dm
Fix a trivial conflict over adding <dm.h>

Conflicts:
	arch/arm/cpu/armv7/omap3/board.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-10-26 14:03:08 -04:00
Jeroen Hofstee
bf8550287d omap3: board: add missing include and proto
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 15:27:35 -04:00
Jeroen Hofstee
98431d5881 omap3: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:02:02 -04:00
Simon Glass
b3f4ca1135 dm: omap3: Move to driver model for GPIO and serial
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
2014-10-23 19:29:07 -06:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Jeroen Hofstee
fd3f401bc1 omap3: board: trivial: add void for no args
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-19 17:53:58 -04:00
Simon Glass
7e4154a553 am33xx/omap: Allow cache enable for all Sitara/OMAP
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined.
This speeds up the Beaglebone Black boot considerable.

(Tested only on Beaglebone Black with SD card boot)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-11 16:25:39 -04:00
Wolfgang Denk
e7300f463d ARM: OMAP: remove sr32() from OMAP board code
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Andreas Bießmann
da634ae356 omap_gpmc: change nandecc command
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine.  Currently we support 1-bit hammign
and 8-bit BCH on HW backend.

In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
2013-04-08 11:29:05 -04:00
Enric Balletbo i Serra
b51a5e3a0a OMAP3: Initialize gpmc if SPL_ONENAND_SUPPORT is enabled.
In order to use SPL boot from OneNAND we should initialize the gpmc.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-11 11:06:08 -04:00
Nikita Kiryanov
e3913f56a2 omap_hsmmc: add driver check for write protection
Add check for write protection in omap mmc driver.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
e874d5b001 omap_hsmmc: implement driver check for card detection
Implement driver check for card detection.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Robert P. J. Day
e3fe62574d omap3: Add a few comments to "#endif"s for readability.
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10 08:55:25 -07:00
Tom Rini
57f588be60 omap3: Rework board.c for !CONFIG_SYS_L2CACHE_OFF
When CONFIG_SYS_L2CACHE_OFF is defined we end up with a few warnings
currently.  Re-order functions so that we don't have that anymore.

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-30 22:23:28 -07:00
Tom Rini
6507f133f3 SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r.  We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well.  Finally, we no longer call
relocate_code so remove that from the armv7 version.

Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
47f7bcae8c SPL: Move the omap SPL framework to common/spl
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards.  We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/.  We leave
the NAND one in-place as we plan to replace it later in this series.

We use common/spl to avoid linker problems with respect to merging
constant strings in objects.   Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
d7cb93b28a ARM: SPL: Move gpmc_init() to spl_board_init()
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
f0881250f9 ARM: SPL: Make spl_mmc.c more generic
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>.  Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:58 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Tom Rini
8082fda9fc ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.c
This detection code doesn't (and can't) do anything currently, so
remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
37189a1958 ARM: SPL: Rename omap_boot_mode to spl_boot_mode()
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
8e1b836ec5 ARM: SPL: Rename omap_boot_device to spl_boot_device
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Tom Rini
8a87a3d72e omap3: Introduce weak misc_init_r
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15 08:31:28 +02:00
Stefano Babic
da521387a4 OMAP3: SPL: do not call I2C init if no I2C is set.
Call i2c initialization in spl_board_init only if I2C
is configured for the board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
2012-03-27 22:05:29 +02:00
Aneesh V
f1f2c3ca9f armv7: omap3: leave outer cache enabled
Mainline kernel for OMAP3 doesn't enable L2 cache
It expects L2$ to be enabled by ROM-code/bootloader.

Leaving L2$ enabled can be troublesome in cases where
the L2 cache is not under CP15 control, such as in
Cortex-A9. This problem is explained in detail in
the commit dc7100f408

However, this problem doesn't apply to Cortex-A8
because L2$ in Cortex-A8 is under CP15 control and
hence the generic armv7 maintenance opertions work
for it.

As such we can make an exception for OMAP3 and
leave the L2$ enabled when we jump to kernel. This
is done by removing the strongly-linked implementation
of v7_outer_cache_disable() and allowing it to fall
back to the weakly linked implementation that doesn't
do anything.

Signed-off-by: Aneesh V <aneesh@ti.com>
2012-02-27 21:19:25 +01:00
Peter Meerwald
a4958313fb omap3: fix comment typos
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12 10:11:32 +01:00
Govindraj.R
95f8791042 OMAP3+: Clock: Adding ehci clock enabling
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Andreas Müller
8775471bb3 OMAP SPL: call timer_init in s_init to make udelay work earlier
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2012-01-16 08:40:12 +01:00
Tom Rini
ee08a8260a OMAP3: Add SPL_BOARD_INIT hook
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c.  OMAP4
doesn't need i2c enabled in SPL.  Enable SPL_BOARD_INIT on devkit8000.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Alexander Holler
86623add12 OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.
There is no need to have such a function twice.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-29 15:43:38 +01:00
Tom Rini
cc3f705843 OMAP3 SPL: Provide weak omap_rev_string
We add an weak version of omap_rev_string in omap-common/spl.c
and while at it drop the omap3 version.  Move the prototype over
to <asm/omap_common.h> with the other SPL functions.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:35 +02:00
Simon Schwarz
bb085b87e5 omap-common: add nand spl support
Add NAND support for the new SPL structure.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:54 +02:00
Aneesh V
13d4f9bd74 omap: enable caches at system start-up
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04 11:36:16 +02:00
Aneesh V
080a46eaf1 omap: fix gpio related build breaks
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2011-09-04 11:33:36 +02:00
Aneesh V
25223a68e5 omap: reuse omap3 gpio support in omap4
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
45bf05854b armv7: adapt omap3 to the new cache maintenance framework
adapt omap3 to the new layered cache maintenance framework

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Mans Rullgard
096ca838b5 ARMV7: OMAP3: Convert setup_auxcr() to pure asm
This function consists entirely of inline asm statements, so writing
it directly in a .S file is simpler. Additionally, the inline asm is
not safe as is, since registers are not guaranteed to be preserved
between asm() statements.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:51:09 -04:00
Steve Sakoman
f56348af5d ARM: Rename arch/arm/cpu/arm_cortexa8 to armv7
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9

Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.

The two architectures are similar enough that substantial code can be shared.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:55 -04:00
Renamed from arch/arm/cpu/arm_cortexa8/omap3/board.c (Browse further)