Update this to use log_debug() instead of the old debug().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the security chip is not used in these U-Boot phases. Update
the Makefile to exclude it.
Fix a few logging statements while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the next commit more readable by doing the move now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On the i.MX8M Mini, ret = clk_set_rate() sets ret to the value of the
rate the clock was able to set. When checking for errors, it only
checks that it is not NULL. Since positive numbers are not errors,
only check for negative numbers when handling errors.
Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The code was processed with unifdef utility to omit portions not
relevant to A38x and DDR3. This removes usage of many macros, including
A70X0, A80X0 and A3900. It seems that the unifdef utility did not remove
the macros from #else comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Bump version of a38x DDR3 trianing to version 14.0.0 to reflect the
version in the mv-ddr-devel branch of upstream repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
There is a new version numbering system, where after 18.12.0 came
1.0.0, 2.0.0, and so on until 14.0.0. So 14.0.0 is newer than 18.12.0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 56db5d1464b44df10a02b99e615ebd6f6a35c428 upstream.
@pali suggested this change
In commit 6285efb ("mv_ddr: add support for twin-die combined memory
device") was added support for twin-die combined memory device and
default value for explicitly uninitialized structure members is zero, s
also twin_die_combined is initialized to zero. Which means COMBINED
value.
As prior this commit there was no support for twin-die combined memory
device, default value for twin_die_combined should be NOT_COMBINED. This
change change order of enum mv_ddr_twin_die to ensure that NOT_COMBINED
has value zero.
Signed-off-by: heaterC <airyguy@gmx.de>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2bdd12dd68b1f8e27a03a3443ae49a09a14c18e4 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes code in ddr3_training.c.
Import this change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit c8b301463d508c807a33f7b7eaea98bbda4aa35e upstream.
The funtion returnd cs size in byte instead of MB, that cause
calculation error since the caller was expected to get u32 and when he
got above 4G it refers it as 0.
The fix was to get the cs memory size from function as in MB and then
multiply it by 1MB.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit d653b305d0b3da9727c49124683f1a6d95d5c9a5 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 20c89a28548cdab11f88d2ec8936344af0686a1e upstream.
WL phase correcion stage is failing while using bus_width of 16bit, not
to be fix this stage is un-necessary when working with bus_width of 16
bit.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2d3b9437cf38c06c4330e0de07f29476197f5e04 upstream.
The ODT enable heuristic based on active chip-selects is not always
correct. Some board might use two chip-selects, but have only one ODT
line connected. Allow board specific mv_ddr_topology_map to directly set
the ODT configuration register value.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 3908e20c6c520339e9bddb566823ae5e065d5218 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ab9240402a70cc02496683971779e75eff410ab4 upstream.
- function mv_ddr_spd_die_capacity_user_get() has a bug,
since it insert a user memory enum to it,
instead of SPD memory enum (which are different)
- fix: remove mv_ddr_spd_die_capacity_user_get() function.
- memory size with 64 and 32 bit already calculated correctly
at mv_ddr_mem_sz_per_cs_get() function
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Stefan Chulski <Stefan.Chulski@cavium.com>
Reviewed-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6c705ebc0d70f67ed7cae83ad1978c3305ef25be upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header mv_ddr_topology.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 61a8910998d7b553e80f600ebe8147a8b98f0945 upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 32800667b375ebd1f82120da0f3479b1cf52d96d upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit a165037ec26f301be75e1fabc263643683e85255 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The NOR flash w25q128 denoted by JEDEC ID 0xef4018 actually represents
various models. From Winbond's website, I could only find 3 types of
them:
W25Q128JV-IQ/JQ
datasheet:https://www.winbond.com/resource-files/
w25q128jv%20revg%2004082019%20plus.pdf
W25Q128FV (SPI Mode)
datasheet: https://www.winbond.com/resource-files/
w25q128fv%20rev.m%2005132016%20kms.pdf
W25Q128BV
datesheet: https://www.winbond.com/resource-files/
w25q128bv_revh_100313_wo_automotive.pdf
According to the datasheets, all of these 3 types support BP(0,1,2) and
TB bits in the status register (SR), so it could reuse the flash
protection logic for ST Micro.
So it should be safe to add the SPI_NOR_HAS_LOCK and SPI_NOR_HAS_TB
flags to the w25q128 entry of spi_nor_ids table.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[jagan: remove comments in spi-nor-ids.c]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The set_speed() callback should configure the bus speed, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
ca_do_bch_correction() takes a random value from the stack and starts
counting bitflips from this value. Initialize the counter.
This passed unnoticed as the value is finally ignored in the call
hierarchy.
Fixes: 161df94b3c ("mtd: rawnand: cortina_nand: Add Cortina CAxxxx SoC support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In 8a8d24bd Simon dropped data from all the various _platdata calls
but it seems this wasn't caught for the RNG200 driver from when it
was posted to merged. This fixes that issue.
Fixes: 537f0018 (rng: Add iProc RNG200 driver)
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
VIRTIO_ID_MAX_NUM is the largest device ID plus 1. Therefore a device id
cannot be greater or equal to VIRTIO_ID_MAX_NUM. Fix the comparison
accordingly.
Fixes: 8fb49b4c7a ("dm: Add a new uclass driver for VirtIO transport devices")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
If zynqmp_qspi_set_speed() is called multiple times with the same speed,
then on the second call it will skip recalculating the baud_rate_val as
it assumes the speed is already configured correctly. But it will still
write the baud_rate_val to the configuration register and call
zynqmp_gqspi_set_tapdelay(). Because it skipped recalculating the
baud_rate_val, it will use the initial value of 0 . This causes the
driver to run at maximum speed which for many spi flashes is too fast and
causes data corruption.
Instead only write out a new baud_rate_val if we have calculated the
correct baud_rate_val.
This opens up another issue with the "if (speed == 0)", we don't save
off the new plat->speed_hz value when setting the baud rate on the
speed=0 path. Instead mimic what the Linux zynqmp gqspi driver does, and
have speed==0 just use the same calculation as a normal speed. That will
cause the baud_rate_val to use the slowest speed possible, which is the
safest option.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
