We must call dm_scan_other() after devices from the device tree have been
created, since that function behaves differently if there is no bootstd
device.
Adjust the logic to achieve this.
Also fix the bootflow_system() test which was relying on this broken
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this test sets up a partition table on mmc1. But this is used
by the bootstd tests, so it is not possible to run those after this test
has run, without restarting the Python test harness.
This is inconvenient when running tests repeatedly with 'ut dm'. Move the
test to use mmc2, which is not used by anything.
Signed-off-by: Simon Glass <sjg@chromium.org>
This needs to be able to work (at least partially) without the bloblist
active. Add a condition for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running multiple tests the mmc emulator calls malloc() to obtain the
memory for its disk image. Since the memory is not cleared, it is possible
that it happens to contain a partition table.
The dm_test_part() test (for one) relies on mmc0 being empty on startup.
Zero the memory to ensure that it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no point in trying to match the alias order for bootdevs, since
build_order() either sorts them by priority, uses the boot_targets
environment variable or the bootdev-order property.
Just use the iterator instead, to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than implement this as its own case in build_order(), process the
boot_targets environment variable in the bootstd_get_bootdev_order()
function. This allows build_order() to be simplified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some environment variables provide a space-separated list of strings. It
is easier to process these when they are broken out into an array of
strings.
Add a utility function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This obscures the line number. Update the test to avoid make sure that
the line which failed is displayed, so it is possible to diagnose the
failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently HDMI controller MMIO address is hardcoded. Change that so
address is read from DT node. That will make adding support for new
variants a bit easier.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Currently the sunxi dw-hdmi driver is probed unconditionally,
even if there is no such device.
Switch the driver to probing via a compatible string. This brings many
benefits; the driver is only probed when needed, and now it can read the
DT node.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Add clock/reset definitions for display-related peripherals, including
the display engine, TCONs, and DSI and HDMI encoders, so those drivers
can be converted to DM clock consumers instead of directly manipulating
the CCU registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that a regulator driver exists for this PMIC, hook it up to the
device tree "regulators" subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver handles most voltage regulators found in X-Powers AXP PMICs.
It is based on, and intended to replace, the regulator driver in TF-A.
AXP PMIC regulators can be divided into 6 categories:
- Switches without voltage control => fully supported.
- Single linear range => fully supported.
- Two linear ranges, "step" and "2 * step" => fully supported.
- Two linear ranges, "step" and "5 * step" => only the first range is
supported. No boards are known to use the second range.
- Non-linear voltage values => fully supported.
- LDOs shared with GPIO pins => not supported.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To determine whether we have been booted from an eMMC boot partition, we
replay some of the checks that the BROM must have done to successfully
load the SPL. This involves a checksum check, which currently relies on
the SPL being wrapped in an "eGON" header.
If a board has secure boot enabled, the BROM will only accept the "TOC0"
format, which is internally very different, but uses the same
checksumming algorithm. Actually the only difference for calculating the
checksum is that the size of the SPL is stored at a different offset.
Do a header check to determine whether we deal with an eGON or TOC0
format, then set the SPL size accordingly. The rest of the code is
unchanged.
This fixes booting from an eMMC boot partition on devices with secure
boot enabled, like the Remix Mini PC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
For legacy reasons we were defining the card detect GPIO for all sunxi
boards in each board's defconfig.
There is actually no need for a card-detect check in the SPL code (which
consequently has been removed already), and also in U-Boot proper we
have DM code to query the CD GPIO name from the device tree.
That means we don't have any user of that information left, so can
remove the definitions from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
As the SPL code for sunxi boards does not use the driver model, we have
two mmc_ops structures, one for DM, one for non-DM. The actual hardware
access code is shared, with the respective callback functions using that
common code.
To make this more obvious and easier to read, reorder the functions to
group them: we first have the common code, then the non-DM bits, and
the proper DM implementation at the end.
Also document this structure in the comment at the beginning of the file.
No functional change intended.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The sunxi MMC code does not use the DM in the SPL, as we don't have a
device tree available that early, also no space for it.
This also means we cannot access the card-detect GPIO information from
there, so we have Kconfig symbols called CONFIG_MMCx_CD_PIN, which each
board has to define. This is a burden, also requires extra GPIO code in
the SPL.
As the SPL is the natural successor of the BootROM (from which we are
loaded), we can actually ignore the CD pin completely, as this is what
the BootROM does as well: CD GPIOs are board specific, but the BootROM
is not, so accesses the MMC devices anyway.
Also, as we must have been loaded from an MMC device when reaching this
code, there must have been a card in the slot.
Remove the card detect code from the non-DM implementation of the sunxi
MMC driver, to get rid of this unneeded code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
For some reasons shrouded in mystery, the code saving the FEL state was
saving the SCTLR register twice, with the second copy trying to justify
itself by using its ancient "control register" alias name.
Drop the redundant second copy, both from the fel_stash data structure,
and also the code saving and restoring it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Both the values and the MMIO addresses that we need during the 64-bit FEL
restore are smaller than 2^32, so we don't need to do any 64-bit loads.
Change the loads to only load 32 bits worth of data, that saves us some
bytes for storing the values.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When support for the Allwinner F1C100s SoC was originally introduced,
its DT lacked any MMC nodes, which upset our sunxi-u-boot.dtsi overlay,
when it tried to add an alias to the SD card. To quickly fix this back
then, we guarded that alias with a preprocessor macro.
Now the F1C100s family has gained MMC nodes, so we don't need the
special treatment anymore. Just remove this guard.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The SoC .dtsi originally submitted for the Allwinner F1C100s had the
wrong compatible string for the watchdog, which broke U-Boot's reset
functionality. To quickly fix this, we disable CONFIG_SYSRESET in
cfcf1952c1 ("sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), so that U-Boot's hardcoded reset driver could take over.
After this was properly fixed in the devicetree, we reverted that patch
in 92373de041 ("Revert "sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), however this line sneaked back in with d0ee7f295d
("Convert CONFIG_SYS_PBSIZE to Kconfig"), so during a Kconfig update.
Remove this line (again), to use the proper reset driver.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
- Merge in the final batch of CONFIG to Kconfig/CFG migration work. This
includes a fix for a number of ns16550 or similar UARTs due to a
migration bug. We also pull in a revert for enabling CONFIG_VIDEO on
tools-only_defconfig.
This reverts commit 1cfba53ca4.
Since commit 1cfba53ca4 ("config: tools only: add VIDEO to build
bmp_logo") the build of tools-only_defconfig fails:
| /bin/sh: line 1: tools/bmp_logo: No such file or directory
This has been noticed in OpenEmbedded and Debian [1].
Revert it for now.
[1] https://lists.denx.de/pipermail/u-boot/2023-January/504758.html
Signed-off-by: Fabio Estevam <festevam@denx.de>
Now that all remaining in-tree cases where we define or undef a CONFIG
symbol have been migrated to Kconfig or renamed to CFG we can make the
CI check more robust. We will exclude the doc, tools and arch/arm/dts
directories from this check as they are special cases. Further, we can
exclude the scripts/kconfig/lkc.h and include/linux/kconfig.h files as
the CONFIG values they define are special tooling cases and not real
symbols.
In the case of docs, the only places that currently fail this test are
old documentation that should be rewritten so that we can remove this
special case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In imx_watchdog, clean up the comment to just note the range now, as we
do not need to set the default here as Kconfig does this for us. For
ulp_wdog, set the default value via Kconfig instead.
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For this legacy driver, the only user sets these values in Kconfig, so
we can remove them from the header.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
listed in arch/Kconfig.nxp and match how they're currently used by
select'ing them under the required PowerPC ARCH_xxx options.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
asked in arch/Kconfig.nxp. Set the PowerPC defaults based on
arch/powerpc/include/asm/config_mpc85xx.h and remove the default set in
drivers/mtd/nand/raw/fsl_ifc_nand.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This variable has never been configured to another value at present, and
was not converted to Kconfig. Opt instead to rename this to
MUSB_TIMEOUT.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This is always defined to 5, so use that as the default.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
We can enforce the dependencies of this module via Kconfig now, so do so
rather than with #error statements. Further, we can ensure that all
required values are set to their defaults in Kconfig, and in fact
already do so, so remove the tests here. The exception is
CONFIG_UPDATE_LOAD_ADDR which needed to be migrated to Kconfig in the
first place.
Signed-off-by: Tom Rini <trini@konsulko.com>
In this case, using IS_ENABLED(...) to attempt to load the image results
in harder to read and less useful code, along with having to define a
CONFIG value that would be unused. To maintain the current albeit
slightly odd behavior, maintain that if we have both SPL_FS_FAT and
SPL_SATA_RAW_U_BOOT_USE_SECTOR enabled, we use SPL_FS_FAT for the load.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to not define a CONFIG value when the
CONFIG_AUTOBOOT_STOP_STR_* functionality is not enabled, rework the
assignment of empty and unused (as the code will be discarded under if
0, in the end) values to be AUTOBOOT_STOP_STR_* instead of
CONFIG_AUTOBOOT_STOP_STR_*.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the Linux code for "lib1funcs" has changed rather
dramatically. While a resync would be beneficial, it's outside the scope
of what we need here. Simply remove the define for CONFIG_AEABI and
tests for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Prior to commit 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to
Kconfig") we had defined CONFIG_SYS_NS16550_REG_SIZE to -1 with
DM_SERIAL such that we would then have a size 0 character array. This
resulted in functionally no padding. The confusion on my part came from
dealing with the constraints around platforms that do not use DM_SERIAL
in SPL/TPL. After Andre Przywara reported that sunxi was broken, I've
re-read the code and comments again and thought on this harder. What we
want I believe is what this patch does now.
If DM_SERIAL is defined for this stage, regardless of
CONFIG_SYS_NS16550_REG_SIZE then we will dynamically handle reg shifts
and 'struct ns16550' needs no padding (which is functionally what
unsigned char foo[0] provides). This is the same case as NS16550_DYNAMIC
and DEBUG_UART. Expand the existing comment here slightly.
Otherwise, we will have CONFIG_SYS_NS16550_REG_SIZE set to a non-zero
value, and handle padding within the struct.
Cc: Simon Glass <sjg@chromium.org>
Cc: Sergei Antonov <saproj@gmail.com>
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Fixes: 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
In order to avoid defining CONFIG_ARMV[78_]SECURE_BASE as empty in the
linker scripts, if not already defined, add and use
__ARMV[78_]SECURE_BASE for when the base is not defined and we want the
linker scripts to continue.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is used on both m68k, where CONFIG_SYS_IMMR is not used, and
PowerPC an ARM where it is. Abstract this to a new value rather than
re-defining a CONFIG symbol on m68k.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
