For the eMMC on ST-Ericsson Ux500v2 we need slightly different
configuration values. Use the existing switch statement to match
the peripheral ID of Ux500v2 (0x10480180) and override the necessary
values to make the eMMC work on devices with ST-Ericsson Ux500.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> on stm32f769-disco
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simplify the code a bit by using the common mmc_of_parse() function
instead of duplicating the device tree parsing code. We can still get
a default value for cfg->f_max by assigning it before calling
mmc_of_parse().
Another advantage of this refactoring is that we parse more properties
now, e.g. "non-removable" can be used to disable CD entirely.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> on stm32f769-disco
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simplify the code a bit by using dev_read_addr_ptr() instead of
dev_read_addr(). This avoids having to cast explicitly to void*.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> on stm32f769-disco
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The arm,primecell compatible is used for lots of different types
of devices, e.g. I2C, SPI, coresight, ... We really should not bind
the MMC driver to all of them.
Looking through the device trees in U-Boot there seems to be always
a second compatible string for the pl180 device, either arm,pl180
(already listed) or arm,pl18x. Add the "arm,pl18x" compatible to the
list but remove the generic "arm,primecell".
Note that on Linux these compatibles cannot be found in drivers
because AMBA/primecell devices are matched based on their peripheral ID
instead of the compatible.
This fixes the following error messages when booting the ST-Ericsson
U8500 "stemmy" board with the arm_pl180_mmci driver enabled:
MMC: ptm@801ae000 - probe failed: -38
ptm@801af000 - probe failed: -38
funnel@801a6000 - probe failed: -38
tpiu@80190000 - probe failed: -38
etb@801a4000 - probe failed: -38
Cc: Patrice Chotard <patrice.chotard@st.com>
Fixes: 6f41d1a17e ("mmc: arm_pl180_mmci: Sync compatible with kernel")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> on stm32f769-disco
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix mmc_rpmb_route_frames() implementation to comply with most MMC
drivers that expect some alignment of MMC data frames in memory.
When called from drivers/tee/optee/rpmb.c, the address passed is not
aligned properly. OP-TEE OS inserts a 6-byte header before a raw RPMB
frame which makes RPMB data buffer not 32bit aligned. To prevent breaking
ABI with OPTEE-OS RPC memrefs, allocate a temporary buffer to copy the
data into an aligned memory.
Many RPMB drivers implicitly expect 32bit alignment of the eMMC frame
including arm_pl180_mmci.c, sandbox_mmc.c and stm32_sdmmc2.c
Signed-off-by: Timothée Cercueil <timothee.cercueil@st.com>
Signed-off-by: Timothée Cercueil <litchi.pi@protonmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Read the strobe select value from the device tree property ti,strobe-sel,
required for HS400 speed mode
Fixes: a20008eabd ("mmc: am654_sdhci: Add Support for configuring PHY in J721e")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210525093826.10390-2-a-govindraju@ti.com
All these variables/structure are local and should be static.
Issues are reported by sparse:
drivers/mmc/zynq_sdhci.c:49:11: warning: symbol 'zynqmp_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:50:11: warning: symbol 'zynqmp_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:53:11: warning: symbol 'versal_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:54:11: warning: symbol 'versal_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:546:24: warning: symbol 'arasan_ops' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix these kernel doc warnings:
drivers/mmc/zynq_sdhci.c:181: warning: contents before sections
drivers/mmc/zynq_sdhci.c:236: warning: contents before sections
drivers/mmc/zynq_sdhci.c:291: warning: contents before sections
drivers/mmc/zynq_sdhci.c:297: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sdcardclk_set_phase'
drivers/mmc/zynq_sdhci.c:354: warning: contents before sections
drivers/mmc/zynq_sdhci.c:360: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sampleclk_set_phase'
drivers/mmc/zynq_sdhci.c:467: warning: contents before sections
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Restrict tap_delay value to the allowed size(8bits for itap and 6 bits
for otap) before writing to the tap delay register.
Clear ITAP and OTAP delay bits before updating with the new tap value
for Versal platform.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allow configuring ITAP and OTAP values with zero to avoid failures in
some cases (one of them is SD boot mode). Legacy, SDR12 modes require
to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104
modes ITAP value is zero.
In SD boot mode firmware configures the SD ITAP and OTAP values and
in this case u-boot has to re-configure required tap values(including zero)
based on the operating mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
set_phase() functions are not modifying the ret value and returning
the same uninitialized ret, return 0 instead.
Keep the return type as int to return errors when the tapdelay's are
set via xilinx_pm_request() in future.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Newer SoCs have a self calibration feature, which avoids us writing hard
coded phase delay values into the controller.
Consolidate the code by avoiding unnecessary #ifdefs, and also enabling
the feature for all those newer SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Among the SoCs using the "new timing mode", only the A83T needs to
explicitly switch to that mode.
By just defining the symbol for that one odd A83T bit to 0 for any other
SoCs, we can always OR that in, and save the confusing nested #ifdefs.
Clean up the also confusing new_mode setting on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.
Add the proper casts to make it compile cleanly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds support to piton_mmc driver for OpenPiton-riscv64
This driver has many things set as preconfigured because the hardware
automatically configures most of the settings during startup.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes: 52faec3182 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for the controller present on the AM642 SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
As it has been now two years past the migration deadline, it is required
to have migrated. Remove the check from the Makefile and rework some of
the Kconfig logic slightly to get the functional dependencies of DM_MMC
/ BLK right in both the SPL and non-SPL case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some board like imx8mm-evkb, IO voltage switch from 3.3v to 1.8v need
around 18ms, common code only delay 10ms, so need to delay extra 8ms.
Otherwise voltage switch will timeout when wait for data0 line.
This IO voltage switch time depends on board design, depend on the
PMIC and capacitance. imx8mm-evkb board use PCA9450(PMIC) and 10uF
capacitance.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Common code already handle the voltage switch sequence based on spec,
so remove the redundant voltage switch code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN, these
are reserved bits. Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the
card clock output.
After commit b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support"),
we meet SD3.0 card can't work at UHS mode, mmc_switch_voltage() fail because
the second mmc_wait_dat0 return -ETIMEDOUT. According to SD spec, during
voltage switch, need to gate off/on the card clock. If not set the FRC_SDCLK_ON,
after CMD11, hardware will gate off the card clock automatically, so card do
not detect the clock off/on behavior, so will draw the data0 line low until
next command.
Fixes: b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
This is a straightforward conversion of the old, non-dm driver. It was
done in-place as the deadline for non-dm MMC has passed. Previous
commits ensured that no board depends on the old, non-dm variant. Tested
on a Kirkwood based board with eMMC.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Tested-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Stefan Roese <sr@denx.de>
CC: Gerald Kerma <drEagle@doukki.net>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use dev_seq() to read aliases node's index and pass it as device number
for creating bulk device.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
First check if there is an alias for the device tree node defined with the
given num before checking against device index.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
