Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
The driver was developed with references for more than just
dra7, but never included. At least for omap3, this appears
to be functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO bank numbers do not appear in the device tree, so this
patch makes the gpio name based on the address
(ie gpio@49054000_31 vs gpio4_31)
adam
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With DM and device tree support, let's use the GPIO_ACTIVE_HIGH
and GPIO_ACTIVE_LOW from the device tree as they are intended.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO banks are broken up into two 16-bit registers for each
bank set. Unfortunately, the math that determines how to shift
blindly shifted by the number of the gpio. This worked for gpio
numbers under 32, but higher gpio's are broken. This fixes the
gpio index, so the bank is passed and the shift amount within
the register is passed now instead of the gpio number.
Fixes: 8e51c0f25406("dm: gpio: Add DM compatibility to
GPIO driver for Davinci")
Signed-off-by: Adam Ford <aford173@gmail.com>
AM654 has an arasan sdhci controller and a mmc phy attached to it.
Add basic support for K3 specific arasan sdhci controller.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for K3 based remoteproc driver that
communicates with TISCI to start start a remote processor.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
K3 specific SoCs have a dedicated microcontroller for doing
resource management. Any HLOS/firmware on compute clusters should
load a firmware to this microcontroller before accessing any resource.
Adding support for loading this firmware.
After the K3 system controller got loaded with firmware and started
up it sends out a boot notification message through the secure proxy
facility using the TI SCI protocol. Intercept and receive this message
through the rproc start operation which will need to get invoked
explicitly after the firmware got loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Existing rproc_init() api tries to initialize all available
remoteproc devices. This will fail when there is dependency
among available remoteprocs. So introduce a separate api
that allows to initialize remoteprocs individually based
on id.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Devices from the TI K3 family of SoCs like the AM654x contain a Device
Management and Security Controller (SYSFW) that manages the low-level
device control (like clocks, resets etc) for the various hardware
modules present on the SoC. These device control operations are provided
to the host processor OS through a communication protocol called the TI
System Control Interface (TI SCI) protocol.
This patch adds a system reset driver that communicates to the system
controller over the TI SCI protocol for allowing to perform a system-
wide SoC reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management of
various devices present on the SoC. Various reset functionalities are
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/reset/reset-ti-sci.c driver of
the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a reset operations function pointer to support querying the current
status of a reset control.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To support scenarios where a firmware device node has subnodes that
have their own drivers automatically scan the DT and bind those when
the firmware device gets bound.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
TI-SCI message protocol provides support for controlling of various
physical cores available in SoC. In order to control which host is
capable of controlling a physical processor core, there is a processor
access control list that needs to be populated as part of the board
configuration data.
Introduce support for the set of TI-SCI message protocol apis that
provide us with this capability of controlling physical cores.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since system controller now has control over SoC power management, it
needs to be explicitly requested to reboot the SoC. Add support for
it.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Introduce the fundamental
device management capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for board configuration
to assign resources and other board related operations.
Introduce the board configuration capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Add driver model support for OMAP_SERIAL while reusing
the functions in ns16550.c
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Following build warning appears when pinctrl-single is built for ARM64:
In file included from drivers/pinctrl/pinctrl-single.c:10:0:
drivers/pinctrl/pinctrl-single.c: In function ‘single_configure_pins’:
./arch/arm/include/asm/io.h:43:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define __arch_getw(a) (*(volatile unsigned short *)(a))
Fix this by using phys_addr_t for variable reg instead of u32
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
timer_pre_probe() tries to populate the clock rate from DT. omap
timer driver tries to overwrite this value irrespective of the value
populated fro DT. So update this value only when DT doesn't populate
the clock rate.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In order to handle counter overflows use 64 bit values for counter.
Also load the initial value during probe.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace clrsetbits on ODR register (2 operations: one read + one write)
by writing on the correct bit (SET or RESET) of the BSRR register
(only 1 write operation).
Moreover this register if safe for simultaneous access by 2 master on
the bus.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds support for :
- Rate calculation through muxes and generic dividers
- Basic gate setting propagation
- Reparenting for muxes
- Clock rate setting through generic dividers without reparenting
Support is only added to the Composite VPU and VAPB clocks in order
to support the Video Processing Unit Power Domain clock setup.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.
This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace stm32_serial_setparity by stm32_serial_setconfig
which allows to set serial bits number, parity and stop
bits number.
Only parity setting is implemented.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace setparity by more generic setconfig ops
to allow uart parity, bits word length and stop bits
number change.
Adds SERIAL_GET_PARITY/BITS/STOP macros.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test to avoid access to rx buffer when this buffer is empty.
In this case directly call getc() function to avoid issue when tstc()
is not called.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the OOB size is not multiple of the cache line size, the ARMv7
cache operation still prints "Misaligned operation at range".
=> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 224 b
Erase size 262144 b
subpagesize 4096 b
options 0x00104200
bbt options 0x00060000
=> nand dump 0
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
...
The cache flushing operations won't happen in this case to cover all of
the range to fix this by making sure we have things aligned.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Reword the commit message to be clear this is a direct problem
rather than just a warning]
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The dev_get_priv(dev) is used twice in the probe function.
Replace the second invocation with priv variable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to reset all reset signals as in usb DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Only PCI device 1 and 2 is populated on the R-Car Gen2 internal
PCIe controller. Ignore all other devices. This fix prevents a
duplication of OHCI controller response on slot 0 and 1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add support for operating a PHY attached to ehci-pci. There are
systems where the EHCI controller is internally wired to a PCI
bus and has a PHY connected to it as well, ie. the R-Car Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add timer driver for the Designware APB Timer IP. This is present
for example on the Altera SoCFPGA chips.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
musb stop is musb core call during unregister or shutting down
gadget or host musb. For graceful exit add musb_platform_exit
on musb_stop so-that it can exit the musb platform driver as well.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
musb have platform ops to do proper graceful exit,
so add the exit call and move musb platform exit code
instead of keeping it in driver remove.
This make proper shutdown of musb where .remove will
call disable, exit serially via musb_stop.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
reset0 is not available for sun4i, 5i and 7i so access
the reset0 offset from ccm via driver data for relevant
Allwinner SoC. this will eventually drop the existing
ifdef for SUN6I.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Allocate struct phy in private structure instead of allocating
locally and assign it to a pointer. This eventually fix miss
alignment phy which is used in another functions.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Also add a 'drv' parameter to filter the children to remove/unbind.
Exporting those functions is a preparatory work for the addition of the
bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also add device_find_global_by_ofnode() that also find a device based on
the OF node, but doesn't probe the device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Command "dm tree" dumps the devices with class, driver, name information.
Add the index of the device in the class too, because the information is
useful for the bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is the reciprocal of uclass_find_device().
It will be used to print the index information in dm tree dump.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add an entry in usb_gadget_controller_number() for the DWC3 gadget
controller. Without it, it is not possible to bind the USB Ethernet driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With upcoming changes that require CONFIG_BLK, this broke
USB Mass Storage on the OMAP3 boards because if CONFIG_BLK is
enabled, it assumes that DM_USB is enabled, but it wasn't yet
available on omap3 and omap4 boards.
This patch converts the OMAP2430 MUSB glue to support DM_USB and
extracts the necessary information based on the device tree.
It's based on the ti-musb driver, but there are enough significant
differences in both the architecture and device tree entires between
am33xx and OMAP3/OMAP4, that I think it makes sense to continue to
keep the separate.
Per doc/driver-model/usb-info.txt, the USB gadget stuff hasn't
migrated to DM_USB yet, so this only supports USB Host for now.
Users wanting USB Gadgets will need to disable DM_USB and leave
it the old way for now.
Signed-off-by: Adam Ford <aford173@gmail.com>
A bunch of code was encapsulated in #ifdef's whether or not
it is building or for U-Boot. Since this code is always building
for U-Boot, this patch removes the dead code.
Signed-off-by: Adam Ford <aford173@gmail.com>
At present if TSC frequency is provided in the device tree, it takes
precedence over hardware calibration result. This swaps the order to
try hardware calibration first and uses device tree as last resort.
This can be helpful when a generic dts (eg: coreboot/efi payload) is
supposed to work on as many hardware as possible, including emulators
like QEMU where TSC hardware calibration sometimes fails.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_TWL4030_LED
CONFIG_TWL4030_INPUT
This also removes dead references to:
CONFIG_TWL4030_KEYPAD
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recv variable in sandbox_tpm2_fill_buf() is a pointer on a pointer
of a char array. It means accessing *recv is the char array pointer
itself while **recv is the first character of that array. There is no
need for such indirection here, so simplify the code.
Simplifying things will make the last assignment right: "*recv = NULL"
is now correct. The issue has been found by the following Coverity
Scan report:
CID 183371: Incorrect expression (UNUSED_VALUE)
Assigning value "4UL" to "*recv" here, but that stored value is overwritten before it can be used.
232 *recv += sizeof(rc);
233
234 /* Add trailing \0 */
235 *recv = NULL;
While at simplifying things, use '\0' instead of NULL when adding an
empty char at the end of the buffer.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The second check on pcr_map in sandbox_tpm2_xfer() is wrong. It should
check for pcr_map not being empty. Instead, it is a pure copy/paste of
the first check which is redundant.
This has been found thanks to a Coverity Scan report:
CID 183370: Memory - illegal accesses (UNINIT)
Using uninitialized value "pcr_index".
put_unaligned_be32(tpm->pcr_extensions[pcr_index], recv);
This is because pcr_index is initialized only if the user input is
correct, ie. at least one valid bit is set in pcr_map.
Fix the second check and also initialize pcr_index to 0 (which is
harmless in case of error) to make Coverity Scan happy.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case the slow clock is not properly configured, the UTMI clock
cannot lock the PLL, because UPLLCOUNT will "wait X slow clock cycles".
In this case U-boot will loop indefinitely.
Added a timeout in this case, to start U-boot even if UTMI clock is
not enabled, so the user can use different media if needed, or investigate.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a driver for the Xilinx LogiCORE DisplayPort IP core, which is a
pure DP transmitter core for Xiling FPGA (no display capabilities).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The entries of Makefiles should be sorted, which is not the case in the
video driver Makefile.
Sort the entries alphabetically as far as this makes sense.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
