Enable FSPI controller support. So, flash environment can now be used.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adjust environment kernel_addr_r from 0x96000000 to 0x92000000
to fix a bug that failed to boot kernel for ls1012afrwy with 512MiB RAM,
=> tftpboot $kernel_addr_r Image (Image size is 36 MiB)
TFTP error: trying to overwrite reserved memory...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch appends othbootargs to bootargs for LS1021ATWR board.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The eMMC HS200 speed mode on Layerscape platforms has not been
supported properly. The eSDHC clock tuning has not been implemented
by now. So disable it until it is supported properly in case of
any potential issues.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_USB to remove below compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
With DM_USB enabled, enable CONFIG_BLK to remove this
compile warning for ls1012afrdm based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the environment variables from command head file to
ls1028ardb specific head file so that they will not mess
up with ls1028aqds board.
Also updated some variable slightly.
There is no function change by this patch.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1
adapter slot for SDHC1 usage. When SDHC1 is selected in RCW,
do not force to route it to SDHC1 adapter slot if find it
has already been configued for SDHC1_VS.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The pci-host-ecam-generic code assumes that the ECAM is the first PCI
bus in the system to be probed. Therefore, the system-wide bus number
allocated by U-Boot in sequence for it is going to be zero, which
corresponds to the memory-mapped config spaces found within it.
Reuse the logic from other PCI bus drivers, and assume that U-Boot will
allocate bus numbers in sequence for all buses within the current ECAM.
So the base number of the bus needs to be subtracted when indexing the
correct config space.
Fixes: 3675cb044e ("PCI: Add driver for a 'pci-host-ecam-generic' host controller")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The old load address of itb will overwrite uboots reserved memory
on ls1012afrwy with 512 MiB ram
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: cc1aa218f5 ("armv8/ls1046a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: 5a78a472f6 ("armv8/ls1043a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The RGMII modes that include internal delay were not all
properly treated in the memac code. Add support for all
RGMII delay modes.
Fixes: 111fd19e3b ("fm/mEMAC: add mEMAC frame work")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available
to safely contain a kernel, device tree and initrd for relocation. The
way to set fdt_high as 0xffffffff to disable device tree relocation is
removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The fdtdec_get_addr() does not take into account values set in #address-cells
and #size-cells , but assumes them to be 1 for 32bit systems and 2 for 64bit
systems. This is true for most DTs, however there are exceptions. Switch to
fdtdec_get_addr_size_auto_noparent(), which takes the #address/size-cells
values into consideration, otherwise the reset controller node register
offset is incorrectly parsed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use dev_read_addr_ptr() instead of devfdt_get_addr() so that we can support
live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
mmc bootbus and partconf commands are needed in order to be able to
configure booting from separate boot0/boot1 eMMC partitions.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Sub-nodes of /reserved-memory may be disabled. In this case we should not
reserve memory in the memory map.
Reported-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Fixes: fef907b2e4 ("efi_loader: create reservations after
ft_board_setup")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fix
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes: a415d61eac ("cmd: map addresses to sysmem in efidebug memmap")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined
and test_efi_helloworld_net() fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid
access errors like
CACHE: Misaligned operation at range [be0231e0, be0235e0]
seen on the MCIMX7SABRE.
Fixes: d5aee659f2 ("fs: ext4: cache extent data")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
