We introduced special "DEBUG_EFI" defines when the efi loader
support was new. After giving it a bit of thought, turns out
we really didn't have to - the normal #define DEBUG infrastructure
works well enough for efi loader as well.
So this patch switches to the common debug() and #define DEBUG
way of printing debug information.
Signed-off-by: Alexander Graf <agraf@suse.de>
Some times you may want to exit an EFI payload again, for example
to default boot into a PXE installation and decide that you would
rather want to boot from the local disk instead.
This patch adds exit functionality to the EFI implementation, allowing
EFI payloads to exit.
Signed-off-by: Alexander Graf <agraf@suse.de>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch fixes a bug that long word(.l) memory access in 'itest'
command reads the 8bytes of the actual memory on 64-bit architecture.
The cast to the memory pointer should use a fixed bit type.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
If serial support is not compiled into U-Boot, which may be the case
for some SPL builds, the following warning will be generated in disk.c:
cmd/disk.c: In function 'common_diskboot':
cmd/disk.c:16:6: warning: variable 'dev' set but not used [-Wunused-but-set-variable]
int dev, part;
^
The warning is a result of printf() calls being optimized away, and
thus the whole dev variable becomes indeed unused. Mark the variable
as __maybe_unused .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The arm64 Linux boot protocol [1] describes the fields in the Image
header as being 64-bit little endian values.
So fix the endianess conversion to use 64-bit sized operations, for
both image_size and text_offset.
Also we use a local variable for the image_size to avoid both writing
to the header and also accessing it after we actually unmapped it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm64/booting.txt
The qfw command interface used to depend on X86, this patch removes
this restriction so it can be built for sandbox for testing. For normal
usage, it can only be used with CONFIG_QEMU.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The qfw command interface makes use of CONFIG_LOADADDR and
CONFIG_RAMDISKADDR to setup kernel. But not all boards have these macros,
which causes build problem on those platforms.
This patch fixes this issue.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make file names consistent with CONFIG_QFW and CONFIG_CMD_QFW
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch splits qfw command interface and qfw core function into two
files, and introduces a new Kconfig option (CONFIG_QFW) for qfw core.
Now when qfw command interface is enabled, it will automatically select
qfw core. This patch also makes the ACPI table generation select
CONFIG_QFW.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch is part of the qfw refactor work. This patch makes
qemu_fwcfg_present() and qemu_fwcfg_dma_present() public functions.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch is part of the qfw refactor work.
The qemu_fwcfg_free_files() function is only used in error handling in
ACPI table generation, let's not make this a core function and move it
to the right place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch is part of the refactor work of qfw. It adds 3 APIs to qfw
core to iterate firmware list.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Move the command portion of arch/x86/cpu/qemu/fw_cfg.c into
cmd/qemu_fw_cfg.c
- Move arch/x86/include/asm/fw_cfg.h to include/qemu_fw_cfg.h
- Rename ACPI table portion to arch/x86/cpu/qemu/acpi_table.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Merge the parsing of layout aware and layout unaware eeprom commands into
one parsing function. With this change, layout aware commands now follow
the eeprom read and eeprom write conventions of making i2c bus and i2c address
parameters optional.
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Update eeprom_execute_command() and related code to accommodate both layout
aware and layout unaware functions.
No functional changes.
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Make eeprom_execute_command have ulong for i2c_addr]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce parse_i2c_bus_addr() to generalize the parsing of i2c bus number and
i2c device address. This is done in preparation for merging layout aware and
layout unaware command parsing into one function.
No functional changes.
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Introduce the (optional) eeprom print and eeprom update commands.
These commands are eeprom layout aware:
* The eeprom print command prints the contents of the eeprom in a human
readable way (eeprom layout fields, and data formatted to be fit for human
consumption).
* The eeprom update command allows user to update eeprom fields by specifying
the field name, and providing the new data in a human readable format (same
format as displayed by the eeprom print command).
* Both commands can either auto detect the layout, or be told which layout to
use.
New CONFIG options:
CONFIG_CMD_EEPROM_LAYOUT - enables commands.
CONFIG_EEPROM_LAYOUT_HELP_STRING - tells user what layout names are supported
Feature API:
__weak int parse_layout_version(char *str)
- override to provide your own layout name parsing
__weak void __eeprom_layout_assign(struct eeprom_layout *layout, int layout_version);
- override to setup the layout metadata based on the version
__weak int eeprom_layout_detect(unsigned char *data)
- override to provide your own algorithm for detecting layout version
eeprom_field.c
- contains various printing and updating functions for common types of
eeprom fields. Can be used for defining custom layouts.
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The i2c_init function is always provided when CONFIG_SYS_I2C is
defined. No need to limit ourselves to just one supported I2C driver
(soft_i2c). Update the #ifdef conditions to support bus switching for
all I2C drivers.
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
At present the MMC subsystem maintains its own list of MMC devices. This
cannot work with driver model, which needs to maintain this itself. Move the
list code into a separate 'legacy' file. The core MMC code remains, and will
be shared with the driver-model implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the SATA command code includes both the command-processing code
and the core SATA functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.
With this commit:
- All CONFIG option are referenced from the non-command code
- The concept of a 'current SATA device' is confined to the command code
This will make it easier to convert this code to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the IDE command code includes both the command-processing code
and the core IDE functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.
With this commit:
- Most CONFIG option are referenced from the non-command code
- The concept of a 'current IDE device' is confined to the command code
This will make it easier to convert this code to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the SCSI command code includes both the command-processing code
and the core SCSI functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly. This functions use the
new legacy block functions.
With this commit:
- There is no CONFIG option referenced from the command code
- The concept of a 'current SCSI device' is confined to the command code
This will make it easier to convert this code to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we do not build any board with CONFIG_SUPPORT_EMMC_RPMB , this
piece of code evaded conversion. Fix the following compiler error:
cmd/mmc.c: In function 'do_mmcrpmb':
cmd/mmc.c:316:32: error: 'struct blk_desc' has no member named 'part_num'
original_part = mmc->block_dev.part_num;
^
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
I2C_RXTX_LEN from include/i2c.h is not defined if CONFIG_DM_I2C is
enabled. This leads to a compilation error on boards that enable both
CONFIG_CMD_EEPROM and CONFIG_DM_I2C.
To avoid this, we define I2C_RXTX_LEN in cmd/eeprom.c if it is not
already defined.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
Previously, ret could be used uninitialized if
blk_get_device_part_str() failed. Default to ret being set to -1 so
that we always return an err up if we have a problem and then invert the
logic on testing ums_count as when that is non-zero is the time we can
return 0.
Cc: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
By applying this patch, it will give us some flexibility to expose
a selected partition/s.
e.g:
1. To expose several partitions
ums 0 mmc 0:1,0:6
2. To expose the all partitions
ums 0 mmc 0:0
3. To expose multiple partititions on several devices
ums 0 mmc 0:1,1:6
4. It support legacy format
ums 0 mmc 0
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
The bootefi cmd today fetches its device tree pointer from either the
location appointed by "fdt addr" with a fallback to the U-Boot control
fdt.
This integration is unusual for U-Boot and diverges from the way we
usually handle parameters to boot commands. So let's pass the fdt
directly into the bootefi command instead and move the control fdt
logic into the distro boot script.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
The uEFI spec doesn't dictate where the device tree should live at, but
legacy 32bit ARM grub2 has some assumptions that it may stay at its place
when it's already loaded by the firmware.
So let's put it somewhere where Linux that comes after would happily find
it - around the recommended 128MB line.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
When the user did not pass any device tree or the boot script
didn't find any, let's use the system device tree as last resort
to get something the payload (Linux) may understand.
This means that on systems that use the same device tree for U-Boot
and Linux we can just share it and there's no need to manually provide
a device tree in the target image.
While at it, also copy and pad the device tree by 64kb to give us
space for modifications.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Whenever we want to tell our payload about a path, we limit ourselves
to a reasonable amount of characters. So far we only passed in device
names - exceeding 16 chars was unlikely there.
However by now we also pass real file path information, so let's increase
the limit to 32 characters. That way common paths like "boot/efi/bootaa64.efi"
fit just fine.
Signed-off-by: Alexander Graf <agraf@suse.de>
The payload gets information on where it got loaded from. This includes
the device as well as file path.
So far we've treated both as the same thing and always gave it the device
name. However, in some situations grub2 actually wants to find its loading
path to find its configuration file.
So let's split the two semantically separte bits into separate structs and
pass the loaded file name into our payload when we load it using "load".
Signed-off-by: Alexander Graf <agraf@suse.de>
When loading an el torito image, uEFI exposes said image as a raw
block device to the payload.
Let's do the same by creating new block devices with added offsets for
the respective el torito partitions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Create CMD_FDT Kconfig entry to have an option to disable fdt command
which is not required for small configuration which requires libfdt
only.
Enable it by default for all targets which enables OF_LIBFDT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fixup flea3/sandbox/id8313/siemens-am33xx/smartweb]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce env support for sata device.
1. Implement write_env/read_env/env_relocate_spec/saveenv/sata_get_env_dev
2. If want to enable this feature, define CONFIG_ENV_IS_IN_SATA, and
define CONFIG_SYS_SATA_ENV_DEV or implement your own sata_get_ev_dev.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stuart Longland <stuartl@vrt.com.au>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some usb hosts may have failed to probe on "usb start", i.e. an otg
host without an otg-host cable plugged in.
"usb tree" would cause the probe method of these hosts to get called
again, something which should only happen on "usb reset".
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The dm usb_kbd_remove function() will deregister the usb keyboard for
us on a "usb reset" / "usb stop" so there is no need to manually call
usb_kbd_deregister() in the dm case.
This commit removes usb_kbd_deregister() in the dm case fixing the
following "usb reset" errors:
usb_kbd_remove: warning, ret=-6
device_remove: Device 'usb_kbd' failed to remove, but children are gone
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Call blk_dread, blk_dwrite, blk_derase to ensure that the block cache is
used if enabled and to remove build breakage when CONFIG_BLK is enabled.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Call blk_dread, blk_dwrite, blk_derase to ensure that the block cache is
used if enabled and to remove build breakage when CONFIG_BLK is enabled.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a block device cache to speed up repeated reads of block devices by
various filesystems.
This small amount of cache can dramatically speed up filesystem
operations by skipping repeated reads of common areas of a block
device (typically directory structures).
This has shown to have some benefit on FAT filesystem operations of
loading a kernel and RAM disk, but more dramatic benefits on ext4
filesystems when the kernel and/or RAM disk are spread across
multiple extent header structures as described in commit fc0fc50.
The cache is implemented through a minimal list (block_cache) maintained
in most-recently-used order and count of the current number of entries
(cache_count). It uses a maximum block count setting to prevent copies
of large block reads and an upper bound on the number of cached areas.
The maximum number of entries in the cache defaults to 32 and the maximum
number of blocks per cache entry has a default of 2, which has shown to
produce the best results on testing of ext4 and FAT filesystems.
The 'blkcache' command (enabled through CONFIG_CMD_BLOCK_CACHE) allows
changing these values and can be used to tune for a particular filesystem
layout.
Signed-off-by: Eric Nelson <eric@nelint.com>
Make sure to call unmap_sysmem() for address allocated by map_sysmem()
before leaving the function; however this patch gives no impact on
the behavior because map_sysmem()/unmap_sysmem() does nothing except
on Sandbox. Sandbox never runs this code because "booti" is a command
for booting ARM64 kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Command parsing and processing code is not needed when the command line is
disabled. Remove this code in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Check return value of strdup.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
The EFI standard defines a simple boot protocol that an EFI payload can use
to access video output.
This patch adds support to expose exactly that one (and the mode already in
use) as possible graphical configuration to an EFI payload.
With this, I can successfully run grub2 with graphical output.
Signed-off-by: Alexander Graf <agraf@suse.de>
The license command isn't usually built and has a few problems:
- The rules to generate license.h haven't worked in a long time,
re-write these based on the bmp_logo.h rules.
- 'tok' is unused and the license text size has increased
- bin2header.c wasn't grabbing unistd.h to know the prototype for
read().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new Kconfig option for the command line. This is enabled by default,
but when disabled it will remove the command line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All command functions should be static. Update the CBFS functions to follow
this rule.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some controllers do not allow the output value to be read. Detect this and
report the error in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some CPUs use microcode and each core can have a different version of
microcode loaded. Also some CPUs support the concept of an integer ID used
for identification purposes. Add support for these in the CPU uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we switch to including all linker lists in SPL it is important
to not include commands as that may lead to link errors due to other
things we have already discarded. In this case, the SCSI code needs a lot
of attention so for now just guard the command portions.
Signed-off-by: Tom Rini <trini@konsulko.com>
EFI payloads can query for the device they were booted from. Because
we have a disconnect between loading binaries and running binaries,
we passed in a dummy device path so far.
Unfortunately that breaks grub2's logic to find its configuration
file from the same device it was booted from.
This patch adds logic to have the "load" command call into our efi
code to set the device path to the one we last loaded a binary from.
With this grub2 properly detects where we got booted from and can
find its configuration file, even when searching by-partition.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have a nice framework around image fils to prepare a device tree
for OS execution. That one patches in missing device tree nodes and
fixes up the memory range bits.
We need to call that one from the EFI boot path too to get all those
nice fixups. This patch adds the call.
Signed-off-by: Alexander Graf <agraf@suse.de>
In order to execute an EFI application, we need to bridge the gap between
U-Boot's notion of executing images and EFI's notion of doing the same.
The best path forward IMHO here is to stick completely to the way U-Boot
deals with payloads. You manually load them using whatever method to RAM
and then have a simple boot command to execute them. So in our case, you
would do
# load mmc 0:1 $loadaddr grub.efi
# bootefi $loadaddr
which then gets you into a grub shell. Fdt information known to U-boot
via the fdt addr command is also passed to the EFI payload.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
[trini: Guard help text with CONFIG_SYS_LONGHELP]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the host driver to support driver model for block devices. A future
commit will remove the old code, but for now it is useful to be able to use
it both with and without CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
To ease conversion to driver model, add helper functions which deal with
calling each block device method. With driver model we can reimplement these
functions with the same arguments.
Use inline functions to avoid increasing code size on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The comment for file_cbfs_type() says that it returns 0 for an invalid type.
The code appears to check for -1, except that it uses an unsigned variable
to store the type. This results in a warning on 64-bit machines.
Adjust it to make the meaning clearer. Continue to handle the -1 case since
it may be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename this function to blk_get_device_part_str(). This is a better name
because it makes it clear that the function returns a block device and
parses a string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The current name is too generic. The function returns a block device based
on a provided string. Rename it to aid searching and make its purpose
clearer. Also add a few comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The current name is too generic. Add a 'blk_' prefix to aid searching and
make its purpose clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is an enhancement that permits storing the environment file on an
EXT4 partition such as the root filesystem. It is based on the existing
FAT environment file code.
With min() we must use the same type for each parameter. Fix two problems
in trace.c which produce compiler warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix spelling errors in the "booti" help text and bring it more
in line with the bootm/bootz help texts.
Signed-off-by: Karsten Merker <merker@debian.org>
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reported-by: Alex Gdalevich <agdalevich@axion-biosystems.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Heiko Schocher <hs@denx.de>
This is broken - we need to look at the first two characters to distinguish
'gpio status' from 'gpio set'.
Fixes: 0ffe6ab5 (gpio: Allow 's' as an abbreviation for 'status')
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On some systems, RAM starts at address 0. If the user executes itest
against address 0 on such a system, it will call map_physmem(0, ...)
which will return 0 back; mapping only changes the address on sandbox.
This causes itest to believe map_physmem() has failed, and hence fails
the comparison.
Fix itest so that it allows map_physmem() to return 0 /if/ the orignal
address passed to it was also 0.
This fixes "tegra-uboot-flasher flash" on Tegra20.
This has the disadvantage that on sandbox, failed mapping attempts for
address 0 are not detected. Instead, should the code only call
map_physmem() on sandbox? Or, should map_physmem() return its error status
some other way. Or, should the special case only be allowed on systems
where the base of RAM is 0 somehow?
Fixes: 7861204c9a ("itest: make memory access work under sandbox")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All paths should share the same return.
Reported-by: Coverity (CID:134903)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
With CONFIG_DM_PCI enabled, PCI buses are not enumerated at boot, as they
are without that config option enabled. No command exists to enumerate the
PCI buses. Hence, unless some board-specific code causes PCI enumeration,
PCI-based Ethernet devices are not detected, and network access is not
available.
This patch implements "pci enum" in the CONFIG_DM_PCI case, thus giving a
mechanism whereby PCI can be enumerated.
do_pci()'s handling of case 'e' is moved into a single location before the
dev variable is assigned, in order to skip calculation of dev. The enum
sub-command doesn't need the dev value, and skipping its calculation
avoids an irrelevant error being printed.
Using a command to initialize PCI like this has a disadvantage relative to
enumerating PCI at boot. In particular, Ethernet devices are not probed
during PCI enumeration, but only when used. This defers setting variables
such as ethact, ethaddr, etc. until the first network-related command is
executed. Hopefully this will not cause further issues. Perhaps in the
long term, we need a "net start/enum" command too?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In case CONFIG_DM_TPM was set without any TPM chipset configured a fault
was generated (NULL pointer access).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Doing the same fix as is done for ARM by:
"Avoid calling print_eths() with driver model"
(sha1: ff97380015)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that they are in their own directory, we can remove this prefix.
This makes it easier to find a file since the prefix does not get in the
way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.
Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.
Unfortunately, with m68k I get this error:
m68k: + M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o
I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
