In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has the same name as a field in our local private struct, which is
confusing. Change the name to xfer_len instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver is not used by any system and is long unmaintained, drop it.
There is a DWC2 OTG driver which is maintained, see CONFIG_USB_GADGET_DWC2_OTG .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
The host will report such error message if the fastboot device work in
full-speed mode: "Duplicate descriptor for config 1 interface 0
altsetting 0, skipping"
Fastboot device ack both full and high speed interface descriptors when
work in full-speed mode, that's will cause this issue.
Fix it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: John Keeping <john@metanate.com>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
The imx6q arm2 board support has been removed from U-Boot
as it did not get converted to DM.
Remove the MX6Q_ARM2 related ifdefery in the driver.
Signed-off-by: Fabio Estevam <festevam@denx.de>
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that the PHY driver will not try to drive VBUS if it is already
driven by an external supply, there is no need to check the VBUS voltage
before powering on the PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
ISP1760/61/63 are a family of usb controllers, here the main
goal is to support the ISP1763 hcd part found in the MPS3 FPGA
board form Arm. This is based on the kernel driver and ported
to u-boot.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Move urb code from musb only use to a more common scope, so other
drivers in the future can use the handling of urb in usb.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
When usb PHY initialization is done, the PHY need to be reset.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 81755b8c20 ("usb: host: ehci-generic: Make resets and clocks
optional") improved the error check to cover the reset property being
optional. However this was using the wrong error variable for the
check, so would now never fail.
Use the correct error variable for checking the result of
reset_get_bulk(), to actually report genuine errors.
Fixes: 81755b8c20 ("usb: host: ehci-generic: Make resets and clocks optional")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add rk3066a/rk3188 support to rockchip_usb2_phy.c
They don't have completely identical usb phy registers,
so separate comapatible strings and data.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Product id of rk3066 usb otg is 0x300a.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
sandbox_flash_bulk uses priv->read_len to determine if priv->buff contains
the response data (such as from SCSI_INQUIRY). However, if priv->fd=-1 in
handle_read, then priv->read_len is not set even though we are going to
PHASE_DATA. This causes sandbox_flash_bulk to try and read len bytes from
priv->buff, which likely goes past the end of the buffer. Fix this by always
setting priv->read_len even if we aren't going to read anything.
Fixes: f4f715360c ("dm: usb: sandbox: Add an emulator for USB flash devices")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The generic EHCI binding does not *require* resets and clocks
properties, and indeed for instance the Allwinner A20 SoCs does not
need or define any resets in its DT.
Don't easily give up if clk_get_bulk() or reset_get_bulk() return an
error, but check if that is due to the DT simply having no entries for
either of them.
This fixes USB operation on all boards with an Allwinner A10 or A20 SoC,
which were reporting an error after commit ba96176ab7:
=======================
Bus usb@1c14000: ehci_generic usb@1c14000: Failed to get resets (err=-2)
probe failed, error -2
=======================
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This is used to avoid the ports status of IPPC being brought in kernel
stage, it may cause ports error especially when the xhci controller is
a component of dual-role controller.
Reported-by: Yun-Chien Yu <yun-chien.yu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Missing nodes may also be signaled via -ENODATA. We need to check for
that to prevent failing in non-usb3 setups.
Furthermore, dev.phy must be NULL'ed in case usb3-phy was not found.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
When the device tree indicates support for role switching through
the "usb-role-switch" property, take the "role-switch-default-mode"
property into account when deciding which role to put the
controller into.
This makes USB devices work on Apple M1 systems where the device
tree may include a "dr_mode" property that is set to "otg", but
where we need to put the controller into "host" mode to see
devices connected to the type-C ports.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Since commit 16cc5ad0b4 ("power: regulator: add dummy helper")
regulator dummy helper are always available even if DM_REGULATOR
is not set.
DM_REGULATOR flag is no more needed to protect no DM core,
remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The buffer is 512 bytes but read requests can be 800 bytes. Limit the
request to the size of the buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When copying the string in copy_to_unicode(), check for the null
terminator in each position, not just at the start, to avoid reading
beyond the end of the string.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The i.MX8MP glue needs to be configured based on a couple of DT
properties, implement .glue_configure callback to parse those DT
properties and configure the glue accordingly.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Rename the select_dr_mode callback to glue_configure, the callback is
used for more than enforcing controller mode even on the TI chips, so
change the name to a more generic one. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
dev_read_size() returns -EINVAL (-22) if the property "g-tx-fifo-size"
does not exist. If that's the case, we now keep the default value of 0.
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
With the omap-ehci driver now using the phy subsystem to enable
and disable reset, the driver no longer needs to know which
GPIO's are used, and they can be removed from Kconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
There are a few boards that use hard-coded GPIO definitions in
their respective defconfig files. If the GPIO's are listed
in their device trees, the nop-phy can toggle the GPIO's,
so the EHCI driver does not need to know anything about the
GPIO's. Add functions for getting the phys and remove the GPIO
toggles since the phy will now do that.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USB_EHCI_OMAP driver currently has a series of Kconfig options
which let users specify a GPIO for the reset pin. Some devices
may have only one reset, while others might have more.
Since there is a nop phy driver, let's selct enable the PHY
system, and imply the nop phy driver. The nop phy driver can now
toggle the reset pins when putting the phy in and out of reset.
If the gpio is listed under the phy, it will get toggled and
the hard-coded config options specifying the GPIO numbers can
eventually go away.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OMAP3 hierarchy has the ehci node as a sub-node of the
usbhshost. The usbhshost node contains an ohci and an ehci
subnode. The configuration of the ehci belongs in the
EHCI node and not its parent. Move it to the proper probe.
usb start
starting USB...
Bus ehci@48064800: USB EHCI 1.00
Bus usb_otg_hs@480ab000: Port not available.
scanning bus ehci@48064800 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Adam Ford <aford173@gmail.com>
omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function. Remove both from the header along with some additional
checking for DM_USB.
Signed-off-by: Adam Ford <aford173@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are devices which cause a USB stall when trying to read strings.
Specifically Arduino Mega R3 stalls when trying to read the product
string.
The stall currently remains unhandled, and subsequent retries submit new
transfers on a stopped endpoint which ultimately cause a crash in
abort_td():
WARN halted endpoint, queueing URB anyway.
XHCI control transfer timed out, aborting...
Unexpected XHCI event TRB, skipping... (3affe040 00000000 13000000 02008401)
BUG at drivers/usb/host/xhci-ring.c:505/abort_td()!
BUG!
resetting ...
Linux seems to be able to recover from the stall by issuing a
TRB_RESET_EP command.
Introduce reset_ep() which issues a TRB_RESET_EP followed by setting the
transfer ring dequeue pointer via TRB_SET_DEQ. This allows to properly
recover from a USB stall error and continue communicating with the USB
device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The kernel devicetree has definitions for port and hub nodes as subnodes
to the USB devices. These subnodes don't contain all of the data required
to properly configure the dwc3. Check the parent nodes if the data is not
in the port/hub node.
Here's an example from the librem5 kernel dts file
&usb_dwc3_0 {
#address-cells = <1>;
#size-cells = <0>;
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
status = "okay";
port@0 {
reg = <0>;
typec_hs: endpoint {
remote-endpoint = <&usb_con_hs>;
};
};
port@1 {
reg = <1>;
typec_ss: endpoint {
remote-endpoint = <&usb_con_ss>;
};
};
};
&usb_dwc3_1 {
dr_mode = "host";
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
/* Microchip USB2642 */
hub@1 {
compatible = "usb424,2640";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mass-storage@1 {
compatible = "usb424,4041";
reg = <1>;
};
};
};
Signed-off-by: Angus Ainslie <angus@akkea.ca>
The ci_req->hw_buf can be NULL, test whether it is and if so,
avoid accessing it. Else, the system may crash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Li Jun <jun.li@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
In DFU v1.1 specification [1] the DFU_UPLOAD (Short Frame)
is handled only in dfuUPLOADIDLE state:
- Figure A.1 Interface state transition diagram
- the state description in chapter A.2
A.2.3 State 2 dfuIDLE
on Receipt of the DFU_UPLOAD request,and bitCanUpload = 1
the Next State is dfuUPLOADIDLE
A.2.10 State 9 dfuUPLOAD-IDLE
When the length of the data transferred by the device in response
to a DFU_UPLOAD request is less than wLength. (Short frame)
the Next State is dfuIDLE
In current code, when an UPLOAD is completely performed after the first
request (for example with wLength=200 and data read = 9), the DFU state
stay at dfuUPLOADIDLE until receiving a DFU_UPLOAD or a DFU_ABORT request
even it is unnecessary as the previous DFU_UPLOAD request already reached
the EOF.
This patch proposes to finish the DFU uploading (don't go to dfuUPLOADIDLE)
and completes the control-read operation (go to DFU_STATE_dfuIDLE) when
the first UPLOAD response has a short frame as an end of file (EOF)
indicator even if it is not explicitly allowed in the DFU specification
but this seems logical.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit converts i.MX28's EHCI USB host driver to driver model
(DM_USB). It is a straightforward conversion (to reuse as much code
as possible), based on ehci-mx5.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those functions will be re-used when the ehci MXS driver (for imx28)
will be converted to also support CONFIG_DM_USB.
No functional changes introduced - only cosmetic changes (u32 type)
and alignment to pass checkpatch.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is going to be reused with the CONFIG_DM_USB enabled in
the imx28 mxs USB ehci driver.
No functional changes introduced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
For whatever reason, usb_setup_ehci_gadget removes and probes USB device
0. However, not all systems have a device 0. Use the first device
instead.
The device probed should probably have something to do with the
controller (as specified by e.g. ums <controller> or fastboot
<controller>). In fact, I find it odd that we probe the USB device in
the first place, because this is just to set up the gadget itself.
Presumably, the controller should be probed by usb_gadget_initialize
somehow.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix fastboot flash bug.
If the downloading file size is equal to the partition size, "fastboot
flash" can't work, at least in sunxi platform, because used an
uninitalized point: ep->desc.
This patch also fixed 'data abort' bug in am335x platform.
Reproduce: fastboot flash loader1 spl/sunxi-spl.bin.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Fastboot support has been broken on platforms using dwc2 controller
since the gadget gets its max packet size from it.
This patch is the equivalent of 723fd5668f which fixed the same issue
but for the chipidea controller.
Fixes: 27c9141b11 ("usb: gadget: fastboot: use correct max packet size")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This ensures the USB_MUSB_PIO_ONLY config is set to an apppropriate
value from the changes enabling USB_MUSB_GADGET does.
Namely, USB_MUSB_PIO_ONLY default to =y on USB_MUSB_SUNXI being y.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Add support for the proper dwc3 device tree binding support as specified
in the offical device tree spec.
Initially, add support for the LS1028A support. Other SoCs should be
easy to add by just adding the corresponding compatible string.
Unfortunately, the device trees of all other layerscape SoCs are not
converted and uses a wrong compatible string only known in u-boot.
To maintain backwards compatibility with current u-boot device trees,
add the generic "fsl,layerscape-dwc3" compatible string.
OTG mode is not supported yet. The dr_mode in the devicetree will either
have to be set to peripheral or host.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit d9612c2f0449e24983a8b689603210486a930c90]
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit db2be4e9e30c6e43e48c5749d3fc74cee0a6bbb3]
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both dr_mode and maximum-speed properties are usually optional. Drivers
will still try to fetch the properties nonetheless, which leads to error
messages, although they are no errors. Change pr_err() to pr_debug().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
dev_err seems to be moved to different header file. Include
dm/device_compat.h file to compile properly.
Fixes: 69dae8902b ("linux/compat.h: Remove redefinition of dev_xxx macros")
Signed-off-by: Stefan Agner <stefan@agner.ch>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver()
and usb_gadget_unregister_driver() to be able to test
binding usb gadget.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry in usb_gadget_controller_number() for the DWC2
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.
This adds it to the compatible list for this driver.
Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that DM_PCI is always enabled, check on CONFIG_PCI instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for non-PCI users of this code, reword]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which
supports both host and gadget mode. For some reason there is
nothing special about it - add a simple glue driver for Ux500
that literally just sets up MUSB together with a generic PHY.
There are no SoC-specific registers etc needed to make USB work.
The new Ux500 glue driver is only tested to work with DM_USB
and DM_USB_GADGET. Both host and gadget mode work fine on
the u8500 "stemmy" board that is already present in U-Boot.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Signed-off-by: João Loureiro <joaofl@gmail.com>
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c4e ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Even if only USB gadget is defined, dwc3 generic driver enables
a definition and probe/remove functions for host driver.
This enables the definition if USB_HOST is enabled only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
All newer Allwinner SoCs (since about 2013) miss the CONFIGDATA register
in their MUSB implementation, so they need a quirk to hardcode this.
Currently this quirk depends on listing the SoCs affected in musb_reg.h,
which means that this list needs to grow with every new chip.
Move the quirk feature into Kconfig, next to PIO_ONLY, and change the
default to y (for Allwinner builds), while listing the early
implementations as exceptions.
This fixes USB peripheral operation on some newer SoCs, which were not
explicitly listed before.
Tested on H6, H616, R40 (which were broken before), and also on the H5
and A20, for regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
If the PHY isn't specified in the DT, -ENODATA means it should be skipped,
handle it like -ENOENT.
With that, devices without USB3 supported can have USB working (Odroid-HC4).
Fixes: adb049abf7 ("usb: dwc3: Add Meson G12A USB Glue")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
For systems which use generic PHY support and implement USB PHY driver,
the parsing of PHY properties is unnecessary, disable it.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
According to EHCI spec, software needs to do handshake with HC for
safely removing QH from async list. This handshake is implemented by
setting IAAD (Interrupt on Async Advance Doorbell) bit in USB_USBCMD
register and poll the IAA (Interrupt on Async Advance bit) in the
USB_USBSTS to ensure the HC has released all on-chip state that may
potentially reference one of the data structures just removed.
Current codes only check active status of the last QTD, but this can't
ensure the QH is released from HC. We can meet unrecoverable
"EHCI timed out on TD" errors when running UEFI SCT tests on USB disk.
The USB_ASYNCLISTADDR register is changed to a invalid address when the
issue happens. It is fixed after adding the IAA handshake.
Steps to reproduce the issue:
1. Build the UEFI SCT from https://github.com/tianocore/edk2-test
2. Build the EDK2 UEFI Shell from https://github.com/tianocore/edk2
3. Copy SCT files and Shell.efi to USB disk FAT partition
4. Load the Shell.efi from USB FAT, and run bootefi to execute it
5. After booting into Shell, enter the SCT directory and run "sct -a"
to execute all tests.
6. Tests run about 1 hour and stop with many EHCI timeout errors like
EHCI timed out on TD - token=0x801f8c80
Signed-off-by: Ye Li <ye.li@nxp.com>
The iMX8M uses nop PHY, select PHY and NOP_PHY automatically.
Otherwise, the DM capable driver is now perfectly compatible.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Fix cast from pointer to integer of different size by casting the
pointer to uintptr_t instead of uint32_t, the former has correct
size on both 32bit and 64bit architectures.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add new compatible string, used by some more up-to-date DTs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
There is now multiple copies of CONFIG_MXC_USB_PORTSC in configs set to
PORT_PTS_UTMI | PORT_PTS_PTW, which is in fact the default register value
for MX6, MX7 and MX7ULP. Define the default value of CONFIG_MXC_USB_PORTSC
in the driver and use it in case CONFIG_MXC_USB_PORTSC is not defined in
config, to reduce the duplication.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In case PHY support is enabled, use the generic EHCI PHY support
to start and stop the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In case the platform uses DM, determine port number, which is
used as offset in USBMISC registers, from PHY node DT aliases,
just like Linux does.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>