At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Newer SoCs have a self calibration feature, which avoids us writing hard
coded phase delay values into the controller.
Consolidate the code by avoiding unnecessary #ifdefs, and also enabling
the feature for all those newer SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Among the SoCs using the "new timing mode", only the A83T needs to
explicitly switch to that mode.
By just defining the symbol for that one odd A83T bit to 0 for any other
SoCs, we can always OR that in, and save the confusing nested #ifdefs.
Clean up the also confusing new_mode setting on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.
Add the proper casts to make it compile cleanly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds support to piton_mmc driver for OpenPiton-riscv64
This driver has many things set as preconfigured because the hardware
automatically configures most of the settings during startup.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes: 52faec3182 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for the controller present on the AM642 SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
As it has been now two years past the migration deadline, it is required
to have migrated. Remove the check from the Makefile and rework some of
the Kconfig logic slightly to get the functional dependencies of DM_MMC
/ BLK right in both the SPL and non-SPL case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some board like imx8mm-evkb, IO voltage switch from 3.3v to 1.8v need
around 18ms, common code only delay 10ms, so need to delay extra 8ms.
Otherwise voltage switch will timeout when wait for data0 line.
This IO voltage switch time depends on board design, depend on the
PMIC and capacitance. imx8mm-evkb board use PCA9450(PMIC) and 10uF
capacitance.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Common code already handle the voltage switch sequence based on spec,
so remove the redundant voltage switch code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN, these
are reserved bits. Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the
card clock output.
After commit b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support"),
we meet SD3.0 card can't work at UHS mode, mmc_switch_voltage() fail because
the second mmc_wait_dat0 return -ETIMEDOUT. According to SD spec, during
voltage switch, need to gate off/on the card clock. If not set the FRC_SDCLK_ON,
after CMD11, hardware will gate off the card clock automatically, so card do
not detect the clock off/on behavior, so will draw the data0 line low until
next command.
Fixes: b5874b552f ("mmc: fsl_esdhc_imx: add wait_dat0() support")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
This is a straightforward conversion of the old, non-dm driver. It was
done in-place as the deadline for non-dm MMC has passed. Previous
commits ensured that no board depends on the old, non-dm variant. Tested
on a Kirkwood based board with eMMC.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Tested-by: Harm Berntsen <harm.berntsen@nedap.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Stefan Roese <sr@denx.de>
CC: Gerald Kerma <drEagle@doukki.net>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use dev_seq() to read aliases node's index and pass it as device number
for creating bulk device.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
First check if there is an alias for the device tree node defined with the
given num before checking against device index.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.
Signed-off-by: Michael Walle <michael@walle.cc>
The driver currently reads the card-detect but does not register it with
the MMC stack. Update this so that card-detect works as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function finds a device by its driver_info index. With
of-platdata-inst we do not use driver_info, but instead instantiate
udevice records at build-time.
However the semantics of using the function are the same in each case:
the caller provides an index and gets back a device.
So rename the function to device_get_by_ofplat_idx(), so that it can be
used for both situations. The caller does not really need to worry about
the details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCI MMC driver depends on the generic MMC SDHCI driver,
otherwise it does not compile.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
commit e58e68d9 ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value")
wrongly assumed that plat->cfg.f_max is always unset at the time
mscd_drv_probe() is run. This is not true in case max-frequency being
defined in device tree, as it is then already set by mmc_of_parse()
in msdc_of_to_plat().
Only set plat->cfg.f_max to the default maximum value in case it is
not already set to a sane value.
Fixes: e58e68d93e ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value")
Cc: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add tuning functionality which is needed for HS200 mode.
For HS200, program the correct needed 1.8 voltage
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact
cmd6 behavior, after cmd6 get transfer complete interrupt, the data0
line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL.
For other platforms, do not has this issue.
To fix this issue, fix the DTOCV to 0xE, the max setting, this also align
with Linux configuration.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a compatible for i.MX51 so that i.MX51 can use this driver
via driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mmc_spi_sendcmd(), mmc_spi_readdata() and mmc_spi_writedata() are
currently undocumented. Add comment blocks to explain the arguments
and the return value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After command is sent and before card response shows up on the line,
there is a variable number of clock cycles in between called Ncr.
The spec [1] says the minimum is 1 byte and the maximum is 8 bytes.
Current logic in mmc_spi_sendcmd() has a flaw that it could only work
with certain SD cards with their Ncr being just 1 byte.
When resp_match is false, the codes try to receive only 1 byte from
the SD card. On the other hand when resp_match is true, the logic
happens to be no problem as it loops until timeout to receive as many
bytes as possible to see a match of the expected resp_match_value.
However not every call to mmc_spi_sendcmd() is made with resp_match
being true hence this exposes a potential issue with SD cards that
have a larger Ncr value.
Given no issue was reported as of today, we can reasonably conclude
that all cards being used on the supported boards happen to have a 1
byte Ncr timing requirement. But a broken case can be triggered by
utilizing QEMU to emulate a larger value of Ncr (by default 1 byte
Ncr is used on QEMU). This commit fixes such potential spec violation
to improve the card compatibility.
[1] "Physical Layer Specification Version 8.00"
chapter 7.5.1: Command / Response
chapter 7.5.4: Timing Values
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The argument check should happen before any transfer on the SPI lines.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After issuing the switch command: Wait until 'current state' of the card
status becomes 'tran'. This prevents from response timeout at the next
command because of 'current state' = 'data'.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If DMA(SDMA or ADMA) is not used, the cache invalidation
after reading is no need, should be skipped. Otherwise
U-Boot may hang at the cache invalidation.
Found this issue and tested this fix on DragonBoard 410c.
Fixes: commit 4155ad9aac ("mmc: sdhci: fix missing cache invalidation after reading by DMA")
Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
This will allow us to use DM variants of phys_to_bus()/bus_to_phys()
when relevant.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Call mmc_of_parse() so that generic DT properties like 'non-removable'
are taken into account.
This fixes boot on Clearfog with eMMC on SOM that requires the
non-removable property.
Reported-by: Thorsten Spille <thorsten_spille@netcor.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
[1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.
Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert the flags field defines to use the BIT() macro.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The R-Car3 SDHI should set these two bits in DMA_MODE register according
to the specification, to indicate 64bit bus width. No other bus width
options are permitted and the default value is 0, which is incorrect.
Set the bits accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Set this flag so that it is available to those looking at the device. For
non-removable devices there is no need to check for insertion/removable
since the media can never change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present if an eMMC part is in the system, the ACPI table generated
will include information about that, as well as the SD card. We only need
to include the SD card, since it has a card-detect GPIO. Use a different
compatible string for each option, and add code only for the SD card.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently this driver does not set the value of plat->cfg.f_max, which
results in that MMC framework will always run at the lowest frequency.
This patch sets plat->cfg.f_max to the maximum allowed frequency, which
equals to the source clock frequency.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The driver is missing pad control settings (pad delay and pad conf) for
the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will
encounter CRC error on data transfers.
This patch adds default pad control settings for mt7620_compat.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
It turns out that the sclk cycles used by mt7620/mt7628 is the same as
other chips (20 bits, 1048576), not 65536.
This patch removes sclk_cycle_shift from dev_comp, and uses a macro with
a value 20 instead.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
There is no need to define the same macros in drivers.
All macros have been added by commit 17a42abb40 ("mmc: Define timing
macro's").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Freeing a buffer before calling hang() is superfluous. Removing the call
reduces the SPL size.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The driver only needs to retrieve the pin for the ACPI info. The driver
itself works without depending on GPIO.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services
provided by ATF to set SDMMC's DRVSEL and SMPLSEL.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change 'clksel' callback function to allow the code to return a
status.
This patch is a preparation for enabling Arm-Trusted-Firmware (ATF)
in Intel SoC FPGA. This patch does not change functionality.
When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock
related register is secure register which is required to be written
via SMC/PCSI call. It is possible that U-Boot fail to write the
register if there is unexpected error between U-Boot and ATF.
As a result, there maybe signal integrity on MMC connection due to
clock. So, the code should reports error to user when 'clksel' fail.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Define LOG_CATEGORY, use dev_ macro when it is possible.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove unused function in exynos_dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Currently, when different spi slaves claim the bus consecutively using
spi_claim_bus(), spi_set_speed_mode() will only be executed on the first
two calls, leaving the bus in a bad state starting with the third call.
This patch drops spi_slave->speed member and adds caching of bus
speed/mode in dm_spi_bus struct. It also updates spi_claim_bus() to call
spi_set_speed_mode() if either speed or mode is different from what the
bus is currently configured for. Current behavior is to only take into
account the speed, but not the mode, which seems wrong.
Fixes: 60e2809a84 ("dm: spi: Avoid setting the speed with every transfer")
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reported-by: Moshe, Yaniv <yanivmo@amazon.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Regulator can be set to "always-on".
It's not error about enable/disable. It needs to check about
its condition.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It's useful to know an error number when it's debugging.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400,
db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b ("mmc: fsl_esdhc: support eMMC HS400 mode")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All of the existing quirks add retries to various calls of mmc_send_cmd.
mmc_send_cmd_quirks is a helper function to do this retrying behavior. It
checks if quirks mode is enabled, and if a specific quirk is activated it
retries on error.
This also adds mmc_send_cmd_retry, which retries on error every time
(instead of if a quirk is activated).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If the clock driver does not offer a clk_enable ops, then the system will
return -ENOSYS.
The clk_enable works with CCF (common clock framework).
Some clocks in some cases (like the generic clock for some products: sama5d2)
do not have the clk_enable primitive, and in this case probing of the driver
will fail.
This patch changes the behavior to return an error in case there is really
an error, and not a missing primitive.
If the clock driver does not have an enable primitive, most likely clocks
are always enabled or enabled in the set_rate primitives.
Fixes: 81f16438d4 ("mmc: atmel-sdhci: enable the required generic clock")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Amlogic SM1 SoCs doesn't work over 50MHz. When phase sets to 270', it's
working fine over 50MHz on Amlogic SM1 SoCs.
Since Other Amlogic SoCs doens't report an issue, phase value is using
to 180' by default.
To distinguish which value is used adds an u-boot only sm1 compatible.
In future, it needs to find what value is a proper about each SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Move the asm/arch-meson/sd_emmc.h to a local meson_gx_mmc.h,
remove the useless if/then and fix the meson_gx_mmc.c include.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix the condition to set UHS timings for speeds upto HS200.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define default values for input and output clock phase delays for
Versal. Also define functions for setting tapdelays based on these
clock phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define and use functions for setting input and output tapdelays
based on clk phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define input and output clock phase delays with pre-defined values.
Define arasan_sdhci_clk_data type structure and add it to priv
structure and store these clock phase delays in it.
Read input and output clock phase delays from dt. If these values are
not passed through dt, use pre-defined values.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Just group macros below headers. Other patches will be using this location
too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This reverts commit 942b5fc032.
This is partial revert of the above commit.
mmc_of_parse() is reading no-1-8-v from device tree and if set,
it is clearing the UHS speed capabilities of cfg->host_caps.
cfg->host_caps &= ~(UHS_CAPS | MMC_MODE_HS200 |
MMC_MODE_HS400 | MMC_MODE_HS400_ES);
This is still missing to clear UHS speeds like SDHCI_SUPPORT_SDR104,
SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50.
Even if we clear the flags SDHCI_SUPPORT_XXX in mmc_of_parse(),
these speed flags are getting set again in cfg->host_caps in
sdhci_setup_cfg().
The reason for this is, SDHCI_SUPPORT_XXX flags are cleared
only if controller is not capable of supporting MMC_VDD_165_195 volts.
if (caps & SDHCI_CAN_VDD_180)
cfg->voltages |= MMC_VDD_165_195;
if (!(cfg->voltages & MMC_VDD_165_195))
caps_1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
SDHCI_SUPPORT_DDR50);
It means "no-1-8-v", which is read from DT is not coming in to effect.
So it is better we keep the host quirks(SDHCI_QUIRK_NO_1_8_V) to
clear UHS speeds based on no-1-8-v from device tree.
Hence revert the functionality related to no-1-8-v only, rest is fine
in the patch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
dev_err has been used for debugging and a few dev_err message are
printed for normal code execution. Make them dev_dbg instead.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.
Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove a left-over debug test message from the Octeon TX / TX2
MMC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
Since it's so trivial I could just about tolerate this when there were only
two copies of it. But now there are about to be three.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Signed-off-by: Michael Walle <michael@walle.cc>
Currently, readl/writel and esdhc_read32/esdhc_write32 are used. To align
the usage, change to only use esdhc_read32/esdhc_write32.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.
Signed-off-by: Michael Walle <michael@walle.cc>
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
Signed-off-by: Michael Walle <michael@walle.cc>
Use the dma_{map,unmap}_single() calls. These will take care of the
flushing and invalidation of caches.
Signed-off-by: Michael Walle <michael@walle.cc>
SDMA can only do DMA with 32 bit addresses. This is true for all
architectures (just doesn't apply to 32 bit ones). Simplify the code and
remove unnecessary CONFIG_FSL_LAYERSCAPE.
Also make the error message more concise.
Signed-off-by: Michael Walle <michael@walle.cc>
This 1ms delay before sending command already exist from the beginning
of the fsl_esdhc driver added in year 2008. Now this driver has been
split for two files: fsl_esdhc.c and fsl_esdhc_imx.c. fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay
before sending any command. So remove this 1ms, this will save a lot
time if handling a large mmc data.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According to the code logic in __mmc_switch, if the parameter 'send_status'
is zero, no need to send cmd13, just wait the stated timeout time, then
can return directly.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There was a fix-up for eMMC HS400 stability issue in Linux.
Patch link:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/
commit/?id=58d0bf843b49fa99588ac9f85178bd8dfd651b53
Description:
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Introduce the fix-up in u-boot since the issue could be reproduced
in u-boot too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fix mmc->clock with actual clock which is divided by the
controller, and record it with priv->clock which was removed
accidentally.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The process for eMMC HS400 mode for eSDHC is,
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.
This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
This adds a udevice parameter to get_best_delay and msdc_set_mclk so they
can call dev_err properly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Call mmc_of_parse at probe time to fetch all the host properties
from the DT.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The second clock of the IP block (the generic clock), must be explicitly
enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <pengfan@nxp.com>
clk_set_rate will return rate in case of success and zero in case of
error, however it can also return -ev, but it's an ulong function.
To avoid any issues, disregard the return value of this call.
In case this call actually fails, nothing much we can do anyway, but we
can at least try with the previous values (or DT assigned-clocks)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add new compatibility string for matching sama7g5 product.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Use mmc_of_parse() to set the common host properties. That includes
"bus-width", so parsing it can be removed from the driver.
But more importantly, "non-removable" is now respected, which fixes
the usage of eMMC.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Marek Behún <marek.behun@nic.cz>
Since the introduction of 'get_cd' callback in sdhci core,
dragonboard410c's MMC interface is broken. It turns out that 'get_cd'
callback checks for the host_caps for validating the chip select. And
since the msm_sdhci driver is not parsing the host_caps from DT, not
all of the cababilities are parsed properly. This results in the MMC
interfaces to be broken.
Hence, fix this by adding a call to 'mmc_of_parse' during driver probe.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Aníbal Limón <anibal.limon@linaro.org>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- The SDIO signal voltage and max base clock frequency
setting are missing in driver, which causes SDIO
not working.
- The patch adds SDIO signal voltage switch support,
which is based on regulator-gpio of vqmmc-supply, and
sets the max base clock frequency.
- Fix the zero clock value in call to sdhci_setup_cfg()
function.
Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53589
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
[pali: Amended fixup patch]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Adds support for MMC controllers found on OcteonTX or
OcteonTX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Peng Fan <peng.fan@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of recasting and shifting use macros which are designed for taking
upper/lower 32bit value from 64bit variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The capabilities register has a field to indicate whether the host
supports high speed mode or not. Add high speed host_caps based on
this bit instead of enabling it by default.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilnx.com>
Tested-by: Michal Simek <michal.simek@xilnx.com>
(zcu104 with sdhci-caps-mask = <0 0x200000>;)
DT binding is saying that default value is 0 not -1 that's why fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The hardcoded array size leads to array overflows with changes in
speed modes enum in mmc core. Use MMC_MODES_END for otap_del_sel
array declaration to fix this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
After enabling OF_PLATDATA support to both MMC and GPIO drivers add the
support for card detection.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to reduce the footprint of SPL by removing dtb and library
overhead, add OF_PLATDATA support to fsl_esdhc_imx. This initial
approach does not support card detection, which will be enabled after
adding OF_PLATDATA support to GPIO.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed in commit <addf358bac1d2bd0> rename fsl_esdhc_imx
driver to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- driver changed to DM.
- pinctrl-driver/dt is used now instead of configuring the mmc I/O-pins
in the mmc-driver.
- nexell_dwmmc_ofdata_to_platdata() reworked, i.e. valid default values
are used now (where possible) and the appropriate if-blocks have
been removed.
- new dt-property "mmcboost" is used now instead of "CONFIG_BOOST_MMC"
which was not defined anywhere.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
After latest improvements on OF_PLATDATA struct names are generated
based on driver name instead of compatible strings. With this in mind,
using aliases in drivers are not longer needed.
This patch removes code that tried to handle these kind of aliases to
improve readability.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The r8a774a1 is compatible with the generic rcar-gen3-sdhi controller.
This patch adds the compatibilty flag, to support the SDHI controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Write required information into the SSDT to describe the SD card
card-detect pin. Since the required GPIO properties are not present in
the device-tree binding, set them manually for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As per the SD physical layer specification version 7.10, erase
command (CMD38) and stop transmission command (CMD12) will generate
R1b response.
R1b = R1 + busy signal
A non-zero value after the R1 response indicates card is ready for
next command.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Erase block start address (CMD32) and erase block end address (CMD33)
command will generate R1 response for mmc SPI mode.
R1 response is 1 byte long for mmc SPI, so assign 1 byte as a response
for this commands.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Send status command (CMD13) will send R1 response under SD mode
but R2 response under SPI mode.
R2 response is 2 bytes long, so read 2 bytes for mmc SPI mode
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The content of ssr is useful only for erase operations.
This saves erase time.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
R1 response is 1 byte long for mmc SPI commands as per the updated
physical layer specification version 7.10.
So correct the resp and resp_size for existing commands
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
When variable i will become 0, while(i--) loop breaks but variable i will
again decrement to -1 because of i-- and that's why below condition
"if (!i && (r != resp_match_value)" will never execute, So doing "i--"
inside of while() loop solves this problem.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
In commit commit d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
was changed 3.0V IO voltage to 3.3V but it was not done on all places in
omap_hsmmc driver. That commit broke eMMC support on Nokia N900.
This patch fixes that problematic commit and changes 3.0V to 3.3V on all
remaining places in omap_hsmmc driver.
Fixes: d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
On build with 32 bit, there is a warning for int-to-pointer-cast.
Fix the int to pointer cast by using uintptr_t.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add missing space before a comment delimiter.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
We only call the function omap_hsmmc_get_cfg in the case of OMAP34XX or
when we have to iodelay recalibration. Add guards for these checks as
clang will otherwise warn.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Rename DT compatible name
- Remove uneccessary if-statement to support 8-bit buswidth
- Remove redundant error msg
- Use symbolic constants in switch statement
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
Change the mmc displayed name in U-Boot for stm32_sdmmc2 driver to
“STM32 SD/MMC”.
This stm32_sdmmc2 driver is for version 2 of the ST HW IP SDMMC but the
displayed name "STM32 SDMMC2" is confusing for user, between the
instance of SDMMC and the device identifier of MMC.
For example on EV1 board, we have:
STM32MP1> mmc list
STM32 SDMMC2: 0 (SD)
STM32 SDMMC2: 1 (eMMC)
Changed to more clear:
STM32MP1> mmc list
STM32 SD/MMC: 0 (SD)
STM32 SD/MMC: 1 (eMMC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
set_ios_post return type changed from void to int, correcting
the same to fix compilation warning.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Until now, the mmc clock was left in a good enough state by the ROM
code to be used by the controller. However on some SoC, if the ROM
code finds a bootloader on USB or SPI, it might leave the MMC clock
in state the controller cannot work with.
Enable the input clocks provided to the mmc controller. While the
u-boot mmc controller driver is not doing fancy settings like the Linux,
it at least needs to make these clocks are running.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 4 bit MMC controllers have an internal debounce for the SDCD line
with a debounce delay of 1 second. Therefore, after clocks to the IP are
enabled, software has to wait for this time before it can power on the
controller.
Add a deferred_probe() callback which polls on sdcd for a maximum of 2 seconds
before switching on power to the controller or (in the case of no card)
returning a ENOMEDIUM. This pushes the 1 second wait time to when the
card is actually needed rather than at every probe() making sure that
users who don't insert an SD card in the slot don't have to wait such a
long time.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
This driver currently performs cache operation before the DMA start,
but does nothing after the DMA completion.
When reading data by DMA, the cache invalidation is needed also after
finishing the DMA transfer. Otherwise, the CPU might read data from
the cache instead of from the main memory when speculative memory read
or memory prefetch occurs.
Instead of calling the cache operation directly, this commit adds
dma_unmap_single(), which performs cache invalidation internally,
but drivers do not need which operation is being run.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, sdhci_prepare_dma() calls flush_cache() regardless of the
DMA direction.
Actually, cache invalidation is enough when reading data from the device.
This is correctly handled by dma_map_single(), which mimics the DMA-API
in Linux kernel. Drivers can be agnostic which cache operation occurs
behind the scene.
This commit also sanitizes the difference between the virtual address
and the dma address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
host->mmc is already (struct mmc *).
memalign() returns an opaque pointer, so there is no need for casting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use {lower,upper}_32_bits() instead of the combination of cast
and shift.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The same code is run for both SDHCI_QUIRK_32BIT_DMA_ADDR and
define(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER).
Unify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Using the global variable does not look nice.
Add a new field sthci::align_buffer to point to the bounce buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 01298da31d ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read generic MMC properties from device-tree. This allows to specify for
example cd-inverted property and let MMC core to properly handle such
case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Add Support for writing to PHY registers for J721e. There are number of
differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY.
Create a driver_data structure with an ops and flags field and use the
flags field to indicate these differences. The differences are as
follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a
DLL_PRESENT flag to make sure that DLL related registers are accessed
only where they are present. Also add a separate set_ios_post()
callback.
2. The J721e 8 bit instance is not muxed with anything else inside the
SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is
used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in
J721e as compared to 2 bits in AM65x. Add another flag that
distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not been added
in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Convert clock manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get clock manager base address from DT node instead of using
#define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert system manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get system manager base address from DT node instead of
using #define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Adam Ford reports that this change breaks booting on da850-evm and
Bartosz Golaszewski agrees that with the impending release we should
revert the change for now. With that noted:
This reverts commit 21a4d80a71.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
