CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi.
Need to delete clock & power domain properties of
main_timer1 in -r5.dts else won't boot. This is because
timer_init is done during rproc_start to start System Firmware,
but we can't do any clock/power-domain operations before
System Firmware starts.
- same constraint applies to main_uart0
- drop cpsw3g custom DT property 'mac_efuse' and custom
DT node cpsw-phy-sel as driver picks these from standard
property/node.
- include board dts file in -r5 dts file to avoid duplication
of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
As MDIO driver does not support Driver Model, the
pinctrl settings in the MDIO node will not
be applied resulting in PHY not being detected.
To workaround this we add the MDIO pinctrl in
the CPSW3G node in the -u-boot.dtsi file.
Add the missing MDIO and RGMII pinctrl nodes in
k3-am642-r5-evm.dts
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Timer0 runs at 200MHz,and the clock-frequency defined in DT is
incorrect. Fix it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-By: Nishanth Menon <nm@ti.com>
Add u-boot,dm-spl tag in the pinmux device tree node, required for MMCSD1
subsystem.
Fixes: b6059ddc45 ("arm: dts: k3-am642: Add r5 specific dt support")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The AM64x SoC uses a central Device Management and Security Controller
(DMSC) processor that manages all the low-level device controls
including the system-wide SoC reset. The system-wide reset is managed
through the system reset driver.
Add a sysreset controller node as a child of the dmsc node to enable
the "reset" command from U-Boot prompt for the K3 AM642 EVM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM64 as CPSW3G IP with 2 external ports. Add DT entries for the same
(based on kernel DT).
Disable second port as its by default set to ICSS usage on EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
