Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB
or 1 GiB.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for reading One-Time Programmable memory via mailbox, which
communicates with CZ.NIC's firmware on the Secure Processor (Cortex-M3)
of Armada 3720.
Display product serial number and additional info, and also set MAC
addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add myself as the maintainer of CZ.NIC's Turris Omnia and Turris Mox
projects.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada 37xx watchdog driver was recently accepted for mainline
kernel by watchdog subsystem maintainer, but the driver works a little
different than the one in U-Boot. This patch fixes this.
In the previous implementation there was a tiny period of time when the
watchdog was disabled and the system was vulnerables - this was during
pinging, which was done by disabling, setting, and enabling the counter.
Now pinging is done without disabling the watchdog. We use 2 counters:
Counter 1 is the watchdog counter - on expiry, the system is reset.
Counter 0 is used to reset Counter 1 to start counting from the set
timeout again. So Counter 1 is set to be reset on Counter 0 expiry event
event and pinging is done by forcing an immediate expiry event on
Counter 0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add gpio command to defconfig - this can be used to detect whether the
button is pressed or light LEDs.
Add DS1307 RTC driver and the date command.
Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset.
Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP
before network controller is initialized.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
When SFP module is connected directly to CPU module we want the SGMII
lane speed at 1.25 Gbps.
This is a temporary solution till there is a comphy driver in the kernel
capable of changing SGMII speed at runtime.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Restructure the board initialization source.
Remove the module_topology environment variable since it won't be
needed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
-msingle-pic-base is a new gcc(from 4.6) option for ppc and
it reduces the size of my u-boot with about 4 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc> (on MPC8308)
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
- Bugfix for SPI environment optimization
- Spelling fixes
- Remove some defconfigs per various maintainers
- Minor db410, bananapi r2 fixes
- Bump QEMU to v3.1.0 for most platforms
commit 9a9d66f5ef ("env: add spi_flash_read_env function")
breaks Environment functionality, as it reads only
until 2 \0 are found, but fills the buffer with 0x0
instead 0xff which leads in an incorrect crc sum.
Fix: init the read buffer with 0xff instead 0x00
Signed-off-by: Heiko Schocher <hs@denx.de>
The am335x_evm_defconfig supports all am335x_boneblack variants. Remove
the redundant am335x_boneblack_defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On this board SPI is only used to configure the SoC driving the LC TFT
display which is not used in U-Boot. Hence remove SPI support.
Signed-off-by: Felix Brack <fb@ltec.ch>
cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable]
static char mtd_help_text[] =
^~~~~~~~~~~~~
When SYS_LONGHELP is not defined. After looking at how other commands
work, we should surround the whole help text (even its declaration) with
an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling
_CMD_HELP[1] on the help text variable argument to U_BOOT_CMD.
[1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Vexpress ca15_tc2 is failing with 3.1.0 because of QEMU issue.
When this patch is applied
https://patchwork.kernel.org/patch/10754401/
Vexpress can be also turn to newer QEMU version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This change enables setting up specific Qemu version or sha1 for new
targets which are added after (current) v3.0.0 version.
This changes is preparation step for adding new Xilinx Versal Virt
platform which was merge after v3.0.0.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The single job for all Layerscape 10xx platforms is close to, and
sometimes exceeds the time limit for a single job configuration. Break
this down into jobs for LS101x, LS104x and LS108x instead. While in
here, in the name portion of these jobs, refer to them as NXP for ARM
and not Freescale as they've been NXP for quite some time.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on musb driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add reset_valid to check whether given reset is valid
or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on phy driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig
Enabling CLK will select DM_RESET by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update sun50i-a64-ccu.h from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
This should be a part of previous sync patch from
commit 1b39a1834e
Author: Andre Przywara <andre.przywara@arm.com>
Date: Mon Oct 29 00:56:47 2018 +0000
sunxi: A64: Update .dts/.dtsi files
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add initial clock driver for Allwinner A80.
- Implement UART bus clocks via ccu_clk_gate table for
A80, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement UART bus resets via ccu_reset table for A80,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.
arch/arm/boot/dts/sun9i-a80*:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
include/dt-bindings/*/sun9i-a80-*:
commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date: Sat Jan 28 20:22:36 2017 +0800
clk: sunxi-ng: Add A80 Display Engine CCU
Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add initial clock driver for Allwinner H6.
- Implement UART bus clocks via ccu_clk_gate table for
H6, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement UART bus resets via ccu_reset table for H6,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Implement UART resets for all relevant Allwinner SoC
clock drivers via ccu reset table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Implement UART clocks for all Allwinner SoC
clock drivers via ccu clock gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add initial clock driver for Allwinner V3S.
- Implement USB bus and USB clocks via ccu_clk_gate table
for V3S, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for V3S, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner R40.
- Implement USB bus and USB clocks via ccu_clk_gate
for R40, so it can accessed in common clk enable
and disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for R40, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A83T.
- Implement USB bus and USB clocks via ccu_clk_gate table
for A83T, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for A83T, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A23/A33.
- Implement USB bus and USB clocks via ccu_clk_gate table
for A23/A33, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table
for A23/A33, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A31.
- Implement USB ahb1 and USB clocks via ccu_clk_gate table
for A31, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB ahb1 and USB resets via ccu_reset table
for A31, so it can accessed in common reset deassert
and assert functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A10s/A13.
- Implement USB ahb and USB clocks via ccu_clk_gate table
for A10s/A13, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB resets via ccu_reset table for A10s/A13,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A10/A20.
- Implement USB ahb and USB clocks via ccu_clk_gate table
for A10/A20, so it can accessed in common clk enable and
disable functions from clk_sunxi.c
- Implement USB resets via ccu_reset table for A10/A20,
so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner H3/H5.
- Implement USB bus and USB clocks via ccu_clk_gate table for
H3/H5, so it can accessed in common clk enable and disable
functions from clk_sunxi.c
- Implement USB bus and USB resets via ccu_reset table for
H3/H5, so it can accessed in common reset deassert and assert
functions from reset-sunxi.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add common reset driver for all Allwinner SoC's.
Since CLK and RESET share common DT compatible, it is CLK driver
job is to bind the reset driver. So add CLK bind call on respective
SoC driver by passing ccu map descriptor so-that reset deassert,
deassert operations held based on ccu reset table defined from
CLK driver.
Select DM_RESET via CLK_SUNXI, this make hidden section of RESET
since CLK and RESET share common DT compatible and code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A64.
Implement USB clock enable and disable functions for
OHCI, EHCI, OTG and USBPHY gate and clock registers
via ccu clk gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
