This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env
variables is overwriting data at 0 offset, which is wrong. So add default
redund env offset for Zynq, ZynqMP, Versal and microblaze platforms.
Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE).
In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead
of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000.
Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of
ENV_IS_IN_SPI_FLASH config.
Below table specifies platform specific env and env redund offsets.
PLAT ENV_OFFSET ENV_OFFSET_REDUND
---- ---------- -----------------
ZYNQ 0xE0000 0xE40000
ZYNQMP 0x1E00000 0x1E80000
VERSAL 0x7F40000 0x7F00000
MICROBLAZE 0x1080000 0x10C0000
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com
This converts the following to Kconfig:
CONFIG_ENV_RANGE
Now that this is in Kconfig we can enforce a minimum size and so remove
the check in C code to ensure range is larger than size.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_MIN_ENTRIES
CONFIG_ENV_MAX_ENTRIES
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sunxi uses CONFIG_SPI more sanely, and can also now properly
load the environment from SPI flash, let's enable the symbol that
actually considers the SPI flash when accessing the environment.
As this symbol depends on CONFIG_SPI, which we now only enable if the
board has a SPI flash, we can make if "default y" for all Allwinner
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow loading and storing the environment from SPI flash, adjust the
raw offset variables for Allwinner boards to make sense there.
U-Boot (including SPL and other blobs) is loaded from the beginning of
SPI flash, so move the environment location as far back as possible, to
not create unnecessary limits. As those offsets are shared with (now
mostly unused) raw MMC environment, we should respect the common one
megabyte limit, which also makes sense on SPI flash.
So limit the environment for those raw locations to 64KB, and place it
just below 1MB (@960KB).
Those values are currently unused, unless someone forcibly enables the
raw MMC environment. In this case it would break as of now, as the
current offset of 544KB is far too low for the current (arm64) U-Boot
proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
At present U-Boot environment variables, and thus scripts, are defined
by CONFIG_EXTRA_ENV_SETTINGS. It is painful to add large amounts of text
to this file and dealing with quoting and newlines is harder than it
should be. It would be better if we could just type the script into a
text file and have it included by U-Boot.
Add a feature that brings in a .env file associated with the board
config, if present. To use it, create a file in a board/<vendor>
directory, typically called <board>.env and controlled by the
CONFIG_ENV_SOURCE_FILE option.
The environment variables should be of the form "var=value". Values can
extend to multiple lines. See the README under 'Environment Variables:'
for more information and an example.
In many cases environment variables need access to the U-Boot CONFIG
variables to select different options. Enable this so that the environment
scripts can be as useful as the ones currently in the board config files.
This uses the C preprocessor, means that comments can be included in the
environment using /* ... */
Also support += to allow variables to be appended to. This is needed when
using the preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
Currently the MMC environment driver supports storing redundant environment
only in one eMMC partition at different offsets. This is sub-optimal, since
if this one boot partition is erased, both copies of environment are lost.
Since the eMMC has two boot partitions, add support for storing one copy of
environment in each of the two boot partitions.
To enable this functionality, select CONFIG_SYS_REDUNDAND_ENVIRONMENT to
indicate redundant environment should be used. Set CONFIG_SYS_MMC_ENV_PART
to 1 to indicate environment should be stored in eMMC boot partition. Set
CONFIG_ENV_OFFSET equal to CONFIG_ENV_OFFSET_REDUND, and both to the offset
from start of eMMC boot partition where the environment should be located.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add PHY_CORTINA as default option in SYS_MMC_ENV_DEV Kconfig entry as
PHY_CORTINA require SYS_MMC_ENV_DEV value similar to FMAN_ENET or QE.
This helps in resolving compilation failure.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This variable is used for pointing to location where redundant variables
are located. There is no default value. And it doesn't need to be specified
which is showing as warning when savedefconfig is called.
make xilinx_zynqmp_virt_defconfig
#
# configuration written to .config
#
make savedefconfig
scripts/kconfig/conf --savedefconfig=defconfig Kconfig
.config:199:warning: symbol value '' invalid for ENV_OFFSET_REDUND
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is roughly the U-Boot side equivalent to commit
e282c422e0 (tools: fw_env: use erasesize from MEMGETINFO ioctl). The
motivation is the case where one has a board with several revisions,
where the SPI flashes have different erase sizes.
In our case, we have an 8K environment, and the flashes have erase
sizes of 4K (newer boards) and 64K (older boards). Currently, we must
set CONFIG_ENV_SECT_SIZE to 64K to make the code work on the older
boards, but for the newer ones, that ends up wasting quite a bit of
time reading/erasing/restoring the last 56K.
At first, I wanted to allow setting CONFIG_ENV_SECT_SIZE to 0 to mean
"use the erase size the chip reports", but that config
option is used in a number of preprocessor conditionals, and shared
between ENV_IS_IN_FLASH and ENV_IS_IN_SPI_FLASH.
So instead, introduce a new boolean config option, which for now can
only be used with ENV_IS_IN_SPI_FLASH. If left off, there's no change
in behaviour.
The only slightly annoying detail is that, when selected, the compiler
is apparently not smart enough to see that the the saved_size and
saved_offset variables are only used under the same "if (sect_size >
CONFIG_ENV_SIZE)" condition as where they are computed, so we need to
initialize them to 0 to avoid "may be used uninitialized" warnings.
On our newer boards with the 4K erase size, saving the environment now
takes 0.080 seconds instead of 0.53 seconds, which directly translates
to that much faster boot time since our logic always causes the
environment to be written during boot.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
CONFIG_SYS_REDUNDAND_ENVIRONMENT is changing in env_internal.h how u-boot
works with variables. struct environment_s has one byte flags property
which also affects ENV_SIZE macro.
I have reached the case where CONFIG_ENV_IS_NOWHERE is default setup
but custom scripts can be designed in a way that u-boot is asked to
import/export variables from/to file which can be in certain format.
That's why also for this configuration make sense to enable
CONFIG_SYS_REDUNDAND_ENVIRONMENT because it depends on environment file
format.
The patch is removing dependency on this configuration to support selecting
environment file format without any specific dependency where variables are
stored.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the new Kconfig option ENV_SPI_EARLY if you want
to use Environment in SPI flash before relocation.
Call env_init() and than you can use env_get_f() for
accessing Environment variables.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This parallels what I added for FAT in commit 6731bef696, allowing the
environment to be found in a specific partition on the device that the
board's mmc_get_env_dev() returns. On the Banana Pi R2 that means the
device that U-Boot was loaded from; either the internal eMMC or an SD
card.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Zynq is similar to ZynqMP u-boot feature wise that's why also enable
default option for ENV_FAT_DEVICE_AND_PART Kconfig entry.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ENV_IS_IN_EXT4 also need to enable FS_EXT4 which is not covered in Kconfig.
Kconfig reports this as:
WARNING: unmet direct dependencies detected for EXT4_WRITE
Depends on [n]: FS_EXT4 [=n]
Selected by [y]:
- ENV_IS_IN_EXT4 [=y] && !CHAIN_OF_TRUST [=n]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option marks any U-Boot variable which does not have explicit 'w'
writeable flag set as read-only. This way the environment can be locked
down and only variables explicitly configured to be writeable can ever
be changed by either 'env import', 'env set' or loading user environment
from environment storage.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration option which prevents the environment hash table to be
ever cleared and reloaded with different content. This is useful in case
the first environment loaded into the hash table contains e.g. sensitive
content which must not be dropped or reloaded.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the absolute path to the default value of
CONFIG_ENV_EXT4_FILE = "/uboot.env".
This patch avoid the error :
Saving Environment to EXT4... File System is consistent
Please supply Absolute path
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
I don't want to have to specify the device; only the partition.
This allows me to use the same image on internal eMMC or SD card for
Banana Pi R2, and it finds its own environment either way.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the comment for SYS_RELOC_GD_ENV_ADDR as gd->env_addr is updated
in board_r.c::initr_reloc_global_data() under the compilation flags
CONFIG_SYS_RELOC_GD_ENV_ADDR
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, testing whether to compile in support for saving the
environment is a bit awkward when one needs to take SPL_SAVEENV into
account, and quite a few storage drivers currently do not honour
SPL_SAVEENV.
To make it a bit easier to decide whether environment saving should be
enabled, introduce SAVEENV as an alias for the CMD_SAVEENV
symbol. Then one can simply use
CONFIG_IS_ENABLED(SAVEENV)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
All configs are using mmc as default fat interface. That's why make it
default for everybody.
The reason for this patch is to make it default for Xilinx Zynq platform
which is not listed there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch will add default values for ENV_OFFSET
and ENV_SECT_SIZE for Microblaze.
Signed-off-by: Varalaxmi Bingi <varalaxmi.bingi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the SPI flash devices in rockchip are 16MiB size.
So, keeping U-Boot proper offset start from 128MiB with 1MiB
size and then start env of 8KiB would be a compatible location
between all variants of flash sizes.
This patch add env start from 0x14000 with a size of 8KiB.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip do support SPI flash as well, so there is
a possibility of using flash environment for those
use cases.
So, restrict the current env offset, size for MMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I'm also seeing the build failure that commit
7d4776545b env: solve compilation error in SPL
tried to fix, namely that the reference to env_flags_validate from
env_htab cannot be satisfied when flags.o is not built in. However,
that commit got reverted by
d90fc9c3de Revert "env: solve compilation error in SPL"
Necessary, but not sufficient conditions to see this are
CONFIG_SPL=y (obviously)
CONFIG_SPL_ENV_SUPPORT=n (so flags.o does not get compiled)
CONFIG_SPL_LIBCOMMON_SUPPORT=y (so env/built-in.o is part of the SPL link)
Now, these are satisfied for e.g. imx6q_logic_defconfig. But that
builds just fine, and spl/u-boot-spl.map lists .data.env_htab among
the discarded (garbage collected) sections. Yet, on our
mpc8309-derived board, we do see the build failure, so perhaps the
linker works a bit differently on ppc than on ARM, or there's yet some
other configuration option needed to observe the break.
This is another attempt at solving it, which also cleans up
env/Makefile a bit: Introduce a def_bool y symbol CONFIG_ENV_SUPPORT
which complements CONFIG_(SPL/TPL)_SUPPORT. Then use
CONFIG_$(SPL_TPL_)ENV_SUPPORT to decide whether to include the five
basic env/*.o files. For attr.o, flags.o and callback.o, this
shouldn't change anything. Also, common.o and env.o still get
unconditionally built for U-boot proper. But for TPL/SPL, those two
are only included if CONFIG_(SPL/TPL)_SUPPORT is set.
Having that symbol should also allow simplifying conditionals such as
#if !defined(CONFIG_SPL_BUILD) || CONFIG_IS_ENABLED(ENV_SUPPORT)
found in drivers/reset/reset-socfpga.c to just
CONFIG_IS_ENABLED(ENV_SUPPORT).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
UBI must be enabled when the environment is in UBI.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
