CONFIG_NET_MULTI has been removed long time ago by commit 795428fc67
("net: remove CONFIG_NET_MULTI") but 4 boards were added later which wasn't
found. The patch is removing this reference from 4 boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The macro should be passed a state, which should be passed
to the actual function. Otherwise using that macro would
yield a build error.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The ARM Juno boards can be used as somewhat decent machines to run
off-the-shelf distributions, with USB, SATA, GBit Ethernet and 8GB of
DRAM.
With stable DTs in the board's NOR flash this would work really nicely,
however the default boot command is to fetch a kernel and an initrd from
the on-board NOR flash, which sounds somewhat embedded.
Include the config_distro_bootcmd.h header and define the available
devices (starting with USB, to catch USB installer sticks) to make
distributions and UEFI work out of the box.
The NOR flash kernel functionality is still preserved as the last
resort, should all other methods fail.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The generic distro boot sequence iterates over several types of devices,
trying one after another. In doing do, it starts with setting the
"devtype" variable, then uses this later in more generic commands.
Now most (block) device types use a local variable for that, but DHCP
puts the type into the environment, where it shadows any local variables.
As a consequence any boot attempt after bootcmd_dhcp has been run fails:
===========================
VExpress64# run bootcmd_dhcp
...
VExpress64# run bootcmd_sata0
SATA#0:
(3.0 Gbps)
SATA#1:
(No RDY)
Device 0: Model: 16GB SATA Flash Drive ....
... is now current device
Couldn't find partition dhcp 0:1
===========================
This problem typically doesn't show, because DHCP is mostly the last
command to try, but is a problem when this order is different, or when
distro_bootcmd or bootcmd_xxx are run separately or multiple times.
Let bootcmd_dhcp use a local variable, as the other kids do, to make the
order of boot commands irrelevant, and allow repeated calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the result of do_status and always returns a CMD_RET_ value
(-ENOSYS was a possible result of show_pinmux).
This patch also adds pincontrol name in error messages (dev->name)
and treats correctly the status sub command when pin-controller device is
not selected.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change ensures both U-Boot and OP-TEE see the same content
from shared memory when OP-TEE is invoked prior U-Boot relocation.
This change is required since U-Boot may execute with data cache off
while OP-TEE always enables cache on memory shared with U-Boot.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use same type as eth_device->iobase and support addresses greater
than INT_MAX.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmD41JkRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrea8+wgArpcRqyC2nCYtdDl1q/8mWQabct2rUJVt
rzIYzgyPgkRBLQjlE8xgEchzAPOuw0YzQnEz3T80wepBPIy53+QYXaqumd9iuhtm
B1x4r/GumqS4qgn9Pfqxabw2eP8DNbxClc14ExDx3zR1pUwp0DRvnYQV/w+W2RQp
nWFKDdhdnkxuXApiVc01RF/9I+IygstVl1TUklxlw9EGkdpirczIX5cP2lhW9rsV
Cm4fPz4V6AphiUQ4RpllossBNVHHlbVyKOtdGWe4CrERH8Zv8tIVRVeHCr0GydPr
ORhIZTk7hmwTav3Zi4XAQ434UZcRVrJFRkZvv8TpmMhMTVb8+gyZaQ==
=F/gP
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-21jul21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
dtoc improvements to show better warnings
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
It is useful to be able to iterate over block devices. Typically there
are fixed and removable devices. For security reasons it is sometimes
useful to ignore removable devices since they are under user control.
Add iterators which support selecting the block-device type.
Signed-off-by: Simon Glass <sjg@chromium.org>
If SPL fails to boot, try to provide an error code to indicate what is
wrong. For example, if a uclass is missing, this can return -EPFNOSUPPORT
(-96) which provides useful information.
Add a helper for accessing the image-loader name so we can drop the use
of #ifdefs in this code.
Put this feature behind a CONFIG_SHOW_ERRORS option to avoid increasing
the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some comments for struct bloblist_hdr are a bit ambiguous. Update them to
clarify the meaning more precisely. Also document bloblist_get_stats()
properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes a blob needs to expand, e.g. because it needs to hold more log
data. Add support for this. Note that the bloblist must have sufficient
spare space for this to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read this information from the EC. It is useful for
determining whether the battery has enough charge to boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL header has a function for obtaining the phase in capital letters,
e.g. 'SPL'. Add one for lower-case also, as used by sandbox.
Use this to generalise the sandbox logic for determining the filename of
the next sandbox executable. This can provide support for VPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Set MC Firmware size in read commands in
env to 2MB.
Update DDR Memory read address for MC firmware to
0x80a00000 and MC DPC address to 0x80e00000.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reuse the common logic to allow for BOOT_TARGET_DEVICES to list USB as a
possibility if we're building for a platform that will have USB but not
if we don't, so that we don't hit the link-time check for trying to have
USB boot on a non-USB system.
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These USB defines do not change the build as there is no USB support
enabled currently.
Cc: Ian Ray <ian.ray@ge.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The capsule signature is now part of our DTB. This is problematic when a
user is allowed to change/fixup that DTB from U-Boots command line since he
can overwrite the signature as well.
So Instead of adding the key on the DTB, embed it in the u-boot binary it
self as part of it's .rodata. This assumes that the U-Boot binary we load
is authenticated by a previous boot stage loader.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This macro is no longer needed for code flow or #ifdefs. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This macro is no longer needed for code flow or #ifdefs. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is no longer necessary to implement rsa_() functions as no-ops
depending on config options. It is merely sufficient to provide the
prototypes, as the rsa code is no longer linked when unused.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is no longer necessary to implement ecdsa_() functions as no-ops
depending on config options. It is merely sufficient to provide the
prototypes, as the ecdsa code is no longer linked when unused.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The purpose of this change is to enable crypto algorithms to be placed
in linker lists, rather than be declared as a static array. The goal
is to remove the crypto_algos array in a subsequent patch.
Create a new linker list named "cryptos", and search it when
image_get_crypto_algo() is invoked.
NOTE that adding support for manual relocation of crypto_algos within
linker lists is beyond the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We already have a host Kconfig for these SHA options. Use
CONFIG_IS_ENABLED(SHAxxx) directly in the code shared with the host build,
so we can drop the unnecessary indirections.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We already have a host Kconfig for SHA1. Use CONFIG_IS_ENABLED(SHA1)
directly in the code shared with the host build, so we can drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the ENABLE and SUPPORT parts of this, which are redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These option are named inconsistently with other SPL options, thus making
them incompatible with the CONFIG_IS_ENABLED() macro. Rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The ENABLE part of this name is redundant, since all boolean Kconfig
options serve to enable something. The SUPPORT part is also redundant
since Kconfigs can be assumed to enable support for something. Together
they just serve to make these options overly long and inconsistent
with other options.
Rename FIT_ENABLE_SHAxxx_SUPPORT to FIT_SHAxxx
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add the variable used by PXE command for fdtoverlays support
since the commit 69076dff22 ("cmd: pxe: add support for FDT overlays").
Reused the unused "splashimage" address as CONFIG_SPLASH_SOURCE and
CONFIG_VIDEO_LOGO are not activated and U-Boot display the "BACKGROUND"
image found in extlinux.conf to manage splashscreen on stm32mp1 boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default bootmenu is loaded only from eMMC. After this change U-Boot
first tries to load bootmenu from uSD card and if it fails then fallback to
eMMC. People want to boot alternative OS from removable uSD without need to
modify eMMC content. So this backward compatible change allows it.
Part of this change is also optimization of trymmc* macros so they can be
used in preboot macro for loading bootmenu.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-2-pali@kernel.org
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210713141139.15183-1-trini@konsulko.com
The usbtty functionality is not currently used on these two platforms,
disable it.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210708014348.4010-1-trini@konsulko.com
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com> (maintainer:J721E BOARD)
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701142743.26190-1-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc. Note that if we do not find anything
here we will continue to try and Android methods and will start by
trying fastboot.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-3-trini@konsulko.com
This include file is only used by ti_omap5_common.h. Further, the move
is towards using the generic distro boot framework and not this set of
macros. Start by moving all of the contents in directly to where they
are used.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-2-trini@konsulko.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210701132612.7559-1-trini@konsulko.com
The Programmable Real-Time Unit - Industrial Communication
Subsystem (PRU-ICSS) is present of various TI SoCs such as
AM335x or AM437x or the AM654x family. Each SoC can have
one or more PRUSS instances that may or may not be identical.
The PRUSS consists of dual 32-bit RISC cores called the
Programmable Real-Time Units (PRUs), some shared, data and
instruction memories, some internal peripheral modules, and
an interrupt controller. The programmable nature of the PRUs
provide flexibility to implement custom peripheral interfaces,
fast real-time responses, or specialized data handling.
Add support for pruss driver. Currently am654x family
is supported.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-2-lokeshvutla@ti.com
Remove the environment support for various legacy boot methods. With
this, we will now default to booting any distribution that follows the
generic distro boot framework and no longer attempt to boot various
legacy (to this SoC) scripts/etc.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210610230147.22475-1-trini@konsulko.com
autoload: if set to "no" then rarpb, bootp or dhcp commands will
just perform a configuration lookup from the BOOTP / DHCP server,
but not try to load any image using TFTP
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-8-Gireesh.Hiremath@in.bosch.com
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions don't modify the device-ID struct that is passed in, so
mark the argument as const, so the data structure can be declared that
way. This allows it to be placed in the rodata section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When reading a directory in the UEFI file system we have to return file
attributes and timestamps. Copy this data to the directory entry structure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Factor out eMMC boot partition selection code into
default_spl_mmc_emmc_boot_partition() function and implement
weak spl_mmc_emmc_boot_partition(), so that architecture or
board code can override the eMMC boot partition selection.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Enabling promiscuous mode can be useful for DSA switches where each port
has its own MAC address.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
On the Yocto image there is a single partition and the kernel
and dtb are present in the 'boot' directory.
Change it accordingly so that the board can boot the Yocto
image by default.
Use the generic 'load' command instead, which is able to
read from an ext4 partition.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
