Aligning addresses and sizes causes overhead which is unnecessary when we
are not loading from block devices. Remove bl_len when it is not needed.
For example, on iot2050 we save 144 bytes with this patch (once the rest of
this series is applied):
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-144 (-144)
Function old new delta
spl_load_simple_fit 920 904 -16
load_simple_fit 496 444 -52
spl_spi_load_image 384 308 -76
Total: Before=87431, After=87287, chg -0.16%
We use panic() instead of BUILD_BUG_ON in spl_set_bl_len because we still
need to be able to compile it for things like mmc_load_image_raw_sector,
even if that function will not be used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For filesystems, filename serves the same purpose as priv. However,
spl_load_fit_image also uses it to determine whether to use a DMA-aligned
buffer. This is beneficial for FAT, which uses a bounce-buffer if the
destination is not DMA-aligned. However, this is unnecessary now that
filesystems set bl_len to ARCH_DMA_MINALIGN instead. With this done, we can
remove filename entirely.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of relying on the presence of filename to determine whether we are
dealing with a FAT filesystem (and should DMA-align the buffer), have FAT set
bl_len to ARCH_DMA_MINALIGN instead. With this done, we can remove the
special-case logic checking for the presence of filename.
Because filesystems are not block-based, we may read less than the size passed
to spl_load_info.read. This can happen if the file size is not DMA-aligned. This
is fine as long as we read the amount we originally wanted to. Modify the
conditions for callers of spl_load_info.read to check against the original,
unaligned size to avoid failing spuriously.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simplify things a bit for callers of spl_load_info->read by refactoring it
to use units of bytes instead of bl_len. This generally simplifies the
logic, as MMC is the only loader which actually works in sectors. It will
also allow further refactoring to remove the special-case handling of
filename. spl_load_legacy_img already works in units of bytes (oops) so it
doesn't need to be changed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
bl_len must be a power of two, so we can use ALIGN instead of roundup and
similar tricks to avoid divisions.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev and priv serve the same purpose, and are never set at the same time.
Remove dev and convert all users to priv. While we're at it, reorder bl_len
to be last for better alignment.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove NULL assignments to fields in spl_load_info when .load doesn't
reference these fields. This can result in more efficient code. filename
must stay even if it is unused, since load_simple_fit uses it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On real hardware, semihosting calls tend to have a large constant
overhead (on the order of tens of milliseconds). Reduce the number of
calls by one by reusing the existing fd in smh_fit_read, and closing it
at the end of spl_smh_load_image.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The purpose of SHOW_ERRORS is to print extra information. Make it depend
on LIBCOMMON to avoid having to check for two configs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initialize ret to avoid returning garbage if blk_get_devnum_by_uclass_id
fails.
Fixes: 8ce6a2e175 ("spl: blk: Support loading images from fs")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename SPL_MTD_SUPPORT to SPL_MTD in order to match MTD. This allows using
CONFIG_IS_ENABLED to test for MTD support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Since commit 34793598c8 ("mtd: nand: mxs_nand_spl: Remove the page aligned
access") there are no longer any users of nand_get_mtd. However, it is
still important to know what the page size is so we can allocate a
large-enough buffer. If the image size is not page-aligned, we will go off
the end of the buffer and clobber some memory.
Introduce a new function nand_page_size which returns the page size. For
most drivers it is easy to determine the page size. However, a few need to
be modified since they only keep the page size around temporarily.
It's possible that this patch could cause a regression on some platforms if
the offset is non-aligned and there is invalid address space immediately
before the load address. spl_load_legacy_img does not (except when
compressing) respect bl_len, so only boards with SPL_LOAD_FIT (8 boards) or
SPL_LOAD_IMX_CONTAINER (none in tree) would be affected.
defconfig CONFIG_TEXT_BASE
======================= ================
am335x_evm 0x80800000
am43xx_evm 0x80800000
am43xx_evm_rtconly 0x80800000
am43xx_evm_usbhost_boot 0x80800000
am43xx_hs_evm 0x80800000
dra7xx_evm 0x80800000
gwventana_nand 0x17800000
imx8mn_bsh_smm_s2 0x40200000
All the sitara boards have DDR mapped at 0x80000000. gwventana is an i.MX6Q
which has DDR at 0x10000000. I don't have the IMX8MNRM handy, but on the
i.MX8M DDR starts at 0x40000000. Therefore all of these boards can handle a
little underflow.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When allocating a buffer to load compressed data into, we need to ensure we
have enough space for over- and under-flow due to alignment. Otherwise we
will clobber the malloc bookkeeping data. Calculate the correct amount of
overhead and use it when determining the size.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
spl_nand_fit_read unconditionally accesses load->priv. Ensure it is set.
Fixes: 00e180cc51 ("spl: nand: support loading i.MX container format file")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner seems to typically stick to a common MMIO memory map for
several SoCs, but from time to time does some breaking changes, which
also introduce new generations of some peripherals. The last time this
happened with the H6, which apart from re-organising the base addresses
also changed the clock controller significantly. We added a
CONFIG_SUN50I_GEN_H6 symbol back then to mark SoCs sharing those traits.
Now the Allwinner D1 changes the memory map again, and also extends the
pincontroller, among other peripherals.
To mark this generation of SoCs, add a CONFIG_SUNXI_GEN_NCAT2 symbol,
this name is reportedly used in the Allwinner BSP code, and prevents us
from inventing our own name.
Add this new symbol to some guards that were already checking for the H6
generation, since many features are shared between the two (like the
renovated clock controller).
This paves the way to introduce a first user of this generation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
If SPL_LOAD_FIT_OPENSBI_OS_BOOT is enabled, the function
spl_invoke_opensbi should change the target OS type to IH_OS_LINUX.
OpenSBI will load the Linux image as the next boot stage.
The os_takes_devicetree function returns a value of true or false
depending on whether or not SPL_LOAD_FIT_OPENSBI_OS_BOOT is enabled.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to introduce the Opensbi OS boot mode, the next stage boot
image of OpenSBI should be configurable.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All "physical" addresses in SPL must be converted to virtual addresses
before access in order for sandbox to work. Add some calls to map_sysmem in
appropriate places. We do not generally call unmap_sysmem, since we need
the image memory to still be mapped when we jump to the image. This doesn't
matter at the moment since unmap_sysmem is a no-op.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several SPL functions try to avoid performing initialization twice by
caching devices. This is fine for regular boot, but does not work with
UNIT_TEST, since all devices are torn down after each test. Add some
functions to invalidate the caches which can be called before testing these
load methods.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
If EXT4_WRITE is enabled, write capabilities will be compiled into SPL, but
not CRC16. Add an option to enable CRC16 to avoid linker errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The entry point is not always the same as the load address. Use the value
of the entry property if it exists.
Fixes: 8a9dc16e4d ("spl: Add full fitImage support")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_image_info.name contains a reference to legacy_img_hdr. If we allocate
the latter on the stack, it will be clobbered after we return. This was
addressed for NAND back in 06377c5a1f ("spl: spl_legacy: Fix NAND boot on
OMAP3 BeagleBoard"), but that commit didn't fix NOR.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
On non-arm architectures, _image_binary_end is defined as a ulong and not a
char[]. Take the address of it when accessing it, which is correct for
both.
Fixes: 1b8a1be1a1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
MMC devices do not have uclass platdata containing blk_descs, only their
child block devices do. Fortunately, we have a function just for this
purpose. This fixes subsequent calls to spl_mmc_load.
Fixes: bf28d9a659 ("spl: mmc: Use correct MMC device when loading image")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
Add board-specific function used to indicate whether a DTO from fitImage
configuration node 'fdt' property DT and DTO list should be applied onto
the base DT or not applied.
This is useful in case of DTOs which implement e.g. different board revision
details, where such DTO should be applied on one board revision, and should
not be applied on another board revision.
Signed-off-by: Marek Vasut <marex@denx.de>
spl_board_prepare_for_boot() is not called before jumping/invoking atf,
optee, opensbi or linux images.
Jump to image at the end of board_init_r() to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_invoke_atf function will not be returned to SPL. Thus, we need to
set __noreturn function attribute to the function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The bloblist should not be finalised until the image is fully set up.
This allows any final handoff information to be included in the bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than open-coding the property names, use the existing constants
provided for this purpose. This better aligns the simple-FIT code with
the full FIT implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some reason this code was put in the main spl.c file. Move it out
to the FIT implementation where it belongs.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions called spl_load_fit_image(), one in spl.c and one in
spl_fit.c
Rename the second one, to indicate that it relates to simple FIT parsing,
rather than the full version.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature has some helpers in its header file so that its functions
resolve to nothing when the feature is disabled. Add a few more and use
these to simplify the code.
With this there are no more #ifdefs in board_init_r()
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
This code is pretty ugly, with many #ifdefs
There are quite a lot of IH_OS_U_BOOT values so the compiler struggles
to create a jump table here. Also, most of the options are normally
disabled.
Change it to an else...if construct instead. Add an accessor for the
spl_image field behind an #ifdef to avoid needing #ifdef in the C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
It doesn't make sense to have some boards do this differently. Drop the
condition in the hope that the maintainers can figure out any run-time
problems.
This has been tested on qemu-ppce500
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
