Commit graph

14 commits

Author SHA1 Message Date
Scott Wood
b616d9b0a7 nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Wenyou Yang
70341e2ed9 board: atmel: clean up peripheral clock code
Due to introducing the new peripheral clock handle functions,
use these functions to reduce duplicated code.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[Rebased on current master, fixup for at91rm9200ek]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18 21:34:40 +01:00
Wenyou Yang
7e8702a00f arm: at91/spl: mpddrc: add struct atmel_mpddrc_config
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-02 11:49:11 +01:00
Erik van Luijk
c982f6b9bf arm: at91: pmc: replace the constant with a define in at91_pmc.h
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 <<  2).

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-08-21 15:47:03 +02:00
Erik van Luijk
0c01c3e876 arm: at91: mpddr: allow multiple DDR controllers
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-08-21 15:47:02 +02:00
Bo Shen
d85e8914b3 ARM: atmel: at91sam9x5ek: enable spl support
Enable SPL support for at91sam9x5ek board. Now, it supports
boot up from NAND flash and SPI flash.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-04-01 01:04:31 +02:00
Bo Shen
8d7b3638e9 arm: atmel: at91sam9x5: cleanup cs configure for spi
As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-17 17:21:14 +01:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Richard Genoud
bcfc8976e5 at91sam9x5: enable USB support for 9x5ek board.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-12-09 22:38:27 +01:00
Wu, Josh
3a49cd7e1a ARM: at91sam9x5: enable MCI0 support for 9x5ek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-10-17 11:29:25 +02:00
Wu, Josh
1c5794a13e at91sam9x5: set default EBI I/O drive configuration.
This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register).

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-13 14:27:28 +02:00
Wu, Josh
2ab4c74604 at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: voice.shen@atmel.com
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:14 +02:00
Bo Shen
4ed9c88603 arm : at91sam9x5 : fix a small bug for NAND
fix a bug:
  when not boot from NAND, the NAND flash can not be detected.
  Using this to fix it

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:13 +02:00
Bo Shen
f7fa2f3740 arm : Atmel : add at91sam9x5ek board support
Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00