musb udc code depends on usb gadget code provided by CONFIG_USB_DEVICE as
defined in drivers/usb/gadget/Makefile. But this Makefile is not included
into U-Boot build when CONFIG_USB_GADGET is not set. As CONFIG_USB_DEVICE
cannot be enabled together with CONFIG_USB_GADGET it means that dependency
for musb udc code is not compiled during build. Fix it by including
drivers/usb/gadget dependency also when CONFIG_USB_DEVICE is set.
This patch fixes compile errors:
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_zero_data_request':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_rx_ep':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_endpoint_write':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_tx_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_irq':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o:u-boot/drivers/usb/musb/musb_udc.c: more undefined references to `usbd_device_event_irq' follow
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_setup_ep':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_alloc_urb'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_startup_events':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
make: *** [Makefile:1762: u-boot] Error 1
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
U-boot allows the default device tree to be overridden from
the build environment using the DEVICE_TREE variable.
Make sure that we include it in the SPL FIT mkimage build step.
This also fixes a broken image in case CONFIG_OF_LIST and
CONFIG_OF_OVERLAY_LIST are unset (i.e., expected to be supplied
by the DEVICE_TREE env var).
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
For SMBIOS we want to store the numeric version numbers in the tables. It
does not make sense to parse the strings. Instead, add new #defines with
the version and patchlevel.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Macro 'cmd_objcopy_uboot' currently does not work with passed empty command
expanded from 'cmd_static_rela' and therefore dummy command 'true' is set
in 'cmd_static_rela' to workaround this issue.
Eliminate it now by fixing 'cmd_objcopy_uboot' macro to work also with
empty 'cmd_static_rela' macro and remove useless invocation of command
'true'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The existing socfpgaimage always pads the image to the maximum size of
OCRAM size. This will break in the encryption flow where it expects the
image to be un-padded. The encryption tool will do the encryption for
the whole image and append the signature key at end of the image.
The signature key will append to beyond the size of OCRAM if the image
is padded with the maximum size before encryption.
Move the padding step from socfpgaimage to Makefile and pads with objcopy
command.
socfpgaimage will pad the image with 16 bytes aligned (including CRC word),
this is a requirement in encryption flow.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
On more places is used pattern 'command > $@ || rm -f $@'. But it does not
propagate failure from 'command' as 'rm -f' returns success.
Fix it by calling 'false' to correctly propagate failure after 'rm -f'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Calling 'make V=1 all' on Ubuntu 18.04 with gcc version 9.2.1 and GNU Make
version 4.1 fails on error:
scripts/Kbuild.include:220: *** Recursive variable 'echo-cmd' references itself (eventually). Stop.
As a workaround expand 'echo-cmd' variable via 'call' construction instead
of expanding it directly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reported-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: ae897022d7 ("Makefile: Fix u-boot-nodtb.bin target")
At present we always include test/dm from the main Makefile. We have a
CONFIG_UNIT_TEST that should control whether the test/ directory is built,
so rely on that instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a constant U_BOOT_EPOCH with the number of seconds since
1970-01-01. This constant can be used to initialize a software
real time clock until it is updated via the 'sntp' command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This change fixes two issues when building u-boot-nodtb.bin target:
* Remove intermediate binary u-boot-nodtb.bin from disk when static_rela
call (which modifies u-boot-nodtb.bin binary) failed. It is required
because previous objcopy call creates binary and static_rela finish it.
* Do not call static_rela cmd when u-boot-nodtb.bin binary was not
created/updated by previous objcopy call.
Second fix would ensure that u-boot-nodtb.bin binary is not updated when
all prerequisites were up-to-date. And therefore final binary u-boot.bin
is not updated in case all prerequisites were not modified and were
up-to-date.
Now running 'make SOURCE_DATE_EPOCH=0 u-boot.bin' second time now does not
touch u-boot.bin binary in case nothing was modified, so GNU make can
correctly detect that everything is up-to-date.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry type for a firmware blob for a System Control Processor,
given by an entry arg. This firmware is a raw binary blob.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If neither CONFIG_SPL_FIT_SOURCE nor CONFIG_USE_SPL_FIT_GENERATOR is
enabled, U_BOOT_ITS will be undefined, and attempting to make u-boot.itb
will pass invalid arguments to mkimage, causing it to print its help
message.
Remove the rule in that case, so it is more obvious that u-boot.itb is
not something that can be made. This will reduce confusion as platforms
move away from CONFIG_USE_SPL_FIT_GENERATOR, as u-boot.itb was
previously a valid goal for those platforms.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Generate 'u-boot-splx4.sfp' which consist of 4 SPL images required
for booting up Cyclone5/Arria10.
By default, this 'u-boot-splx4.sfp' is generated without extra
padding after each SPL image.
For Cyclone5, 'u-boot-splx4.sfp' contains:
4 x SPL(64KB) = 256KB
For Arria10, 'u-boot-splx4.sfp' contains:
4 x SPL(256KB) = 1024KB
For Cyclone5 using NAND flash image layout for 128 KB memory blocks,
user can 'make' the following target to generate 4 SPL images with
padding:
make u-boot-spl-padx4.sfp
'u-boot-spl-padx4.sfp' contains four 128KB SPL images (each 64KB SPL is
followed by 64KB of zero-padding).
4 x (SPL(64KB) + zero-padding(64KB)) = 512KB
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a new entry argument to the fit entry which allows selection of the
default configuration to use. This is the 'default' property in the
'configurations' node.
Update the Makefile to pass in the value of DEVICE_TREE or
CONFIG_DEFAULT_DEVICE_TREE to provide this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present binman warns about missing external blobs only when the
BUILD_ROM is defined. Enable this behaviour always, since many boards
are starting to use these (e.g. ARM Trusted Firmware's BL31).
Signed-off-by: Simon Glass <sjg@chromium.org>
HTML documentation is generated in doc/output/. This directory shall be
deleted by 'make mrproper'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
every compilation shows this error
Hack for sunxi which doesn't have a proper binman definition for
64-bit boards
not only for sunxi-boards/arm64
fix this by changing to real comments
Fixes: 9f55ee259d0c ("Makefile: sunxi: Don't use binman to build ATF image")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
At present with sunxi 64-bit, the Makefile builds
u-boot-sunxi-with-spl.bin and then binman overwrites it with its own
version. But the binman definition lacks some parts, in particular
BL31.
For now, work around this with a hack.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 42b18df80f ("x86: Makefile: Drop explicit targets built by binman")
This option is used to run arch-specific shell scripts which produce .its
files which are used to produce FIT images. We already have binman which
is designed to produce firmware images. It is more powerful and has tests.
So this option should be deprecated and not used. Existing uses should be
migrated.
Mentions of this in code reviews over the last year or so do not seem to
have resulted in action, and things are getting worse.
So let's add a warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we use the empty string to indicate that there is no FIT
generator, but this doesn't allow an individual board to undefine it.
Create a separate bool instead.
Update the config of the boards which currently have an empty string.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is checked before the config has been loaded by the
Makefile, so it doesn't work.
Move the check to later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On mediatek various files that need to be created by binman. It does not
make sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Also update the binman definition so that idbloader.img is only needed
when SPL is actually being used.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
On tegra various files that need to be created by binman. It does not make
sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
On sunxi various files that need to be created by binman. It does not make
sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This Kconfig is not needed anymore since U-Boot will build the ROM if the
required binary blobs exist.
The BUILD_ROM environment variable used to request that the ROM be built.
Now this always happens if the required binary blobs are available. Update
it to mean that U-Boot should fail if the ROM cannot be built. This
behaviour should be compatible with how it used to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 various files that need to be created by binman. It does not make
sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
Update the Makefile to have a separate, final step which runs binman,
once all input dependencies are present.
This avoid sprinkling the Makefile with arch-specific code.
Signed-off-by: Simon Glass <sjg@chromium.org>
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
