In attempts to speed up SPL and reduce size, the MDIO pin muxing
was inadvertently affected. Since the ethernet driver will setup
the pin muxing when ethernet is loaded, this patch will also
pinmux the MDIO pins at the same time. Once an DM compatible
MDIO driver is available, this can be removed.
Fixes: 877ab2423b ("ARM: davinci: da850: Manual pinmux only
when PINCTRL not available")
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds SPI and SPI_FLASH DM support for verified boot on
TI AM335 chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
This patch adds BLK and DM support for verified boot on TI AM335x
chipsets. The following compile warnings are removed:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
BLK and DM_MMC are enabled by default in SPL as well, which is
making the build to break with an overflow(spl image doesn't
fit into SRAM because of size constraints).
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 116 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
For the above reason BLK and DM_MMC is disabled in SPL.
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A72 U-Boot and SPL, so disable it from
the j721e_evm_a72 defconfig.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A72 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A53 U-Boot and SPL, so disable it from
both the GP and HS AM65x A53 defconfigs.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A53 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The commit 355be915ed ("arm: dts: k3-am654: Update power-domains
property for each node") has updated the power-domain cells value
and updated power-domains property in various existing dts nodes but
missed updating the cpsw_nuss node. This results in the following
build warning, fix this.
arch/arm/dts/k3-am654-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
Fixes: 355be915ed ("arm: dts: k3-am654: Update power-domains property for each node")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The MTDPARTS currently lists just u-boot.ais as 512k in size.
This works when loading the ais file via serial port, but if one
wanted to update just the u-boot portion, it's not really possible.
This patch splits the MTDPARTS into a 32k SPL partiion and a 480k
u-boot partition which allows u-boot.img to be burned to the u-boot
partition. The remaining partitions are left with the same sizes
and offsets to not break backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
We are going to implement DTBO partition for BeagleBoard X15 further. To
support this, 'dtimg' command must be enabled.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
It is essential to have an access to BCB area of 'misc' partition on
Android devices [1]. For BeagleBoard X15 the 'bcb' command will be
further used for reboot reason implementation and booting to recovery.
It can be also used for debugging reasons, like checking RescueParty
messages in BCB area.
[1] doc/android/bcb.txt
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
"fastboot flashall" expects "fastboot getvar product" value to be one of
values provided in android-info.txt file (in AOSP), from "require
board=" list. Before this patch, "am57xx" is returned for all AM57xx
based boards, as it's set in $board env var from SYS_BOARD in
board/ti/am57xx/Kconfig file, which is used for default implementation
of "fastboot getvar product".
In order to fix that inconsistency, let's do next:
1. In U-Boot: override fastboot.product, reusing the value from
$board_name
2. In AOSP: provide values for all AM57xx boards we can use to
device/ti/beagle_x15/board-info.txt file
This way requirements check in "fastboot flashall" will work as
expected, verifying that user tries to flash images to the board which
those images were built for.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
In case of Android boot, reboot reason can be written into BCB (usually
it's an area in 'misc' partition). U-Boot then can obtain that reboot
reason from BCB and handle it accordingly to achieve correct Android
boot flow, like it was suggested in [1]:
- if it's empty: perform normal Android boot from eMMC
- if it contains "bootonce-bootloader": get into fastboot mode
- if it contains "boot-recovery": perform recovery boot
The latter is not implemented yet, as it depends on some features that
are not implemented on TI platforms yet (in AOSP and in U-Boot).
[1] https://marc.info/?l=u-boot&m=152508418909737&w=2
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
First thing we check in meson_clk_set_rate_by_id() is current_rate == rate.
There is not need to check it again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd
with the following specifications:
- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver
The board directory is W400, the name of the Amlogic Reference Design
of Amlogic G12B with Gigabit boards, which will be used for similar
boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
When configured with 4GiB DRAM size, only 3.8GiB is available, the
I/O beeing mapped in the last 256MiB of the first 4GiB physical memory/
First fixup the mm_region to handle the first 3.8GiB as memory and the
last 256MiB as I/O.
Then limit the real memory reported by the firmware to the available
physical space, 3.8GiB aligned with the mm_region memory zone size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").
Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
The comment about init op being NULL used to be next to the NULL check
code. Commit 8ca51e51c1 ("dm: mmc: Add a way to use driver model for
MMC operations") separated the comment from the code. Put them back
together.
Fixes: 8ca51e51c1 ("dm: mmc: Add a way to use driver model for MMC operations")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When reading large data in once (reading 512MiB is tested on MT7623), a
watchdog timeout is triggered due to watchdog not being fed.
This patch adds WATCHDOG_RESET() to msdc_start_data() so the watchdog will
be fed every 1024 blocks are read/written.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The standard property name for chip-detect gpio is "cd-gpios". All
in-tree DT files use only this name.
Fixes: 451931ea70 ("mmc: sdhci: Read cd-gpio from devicetree")
Cc: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add a standalone MMC block write test. This allows direct testing of MMC
access rather than relying on doing so as a side-effect of e.g. DFU or
UMS testing, which may not be enabled on all platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the device not binded with a node, we need ignore
the parents and rate settings.
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When support Clock Common Framework, U-Boot use dev for
clk tree information, there is no clk->parent. When
support composite clk, it contains mux/gate/divider,
but the mux/gate/divider is not binded with device.
So we could not use dev_get_uclass_priv to get the correct
clk_mux/gate/divider. So add clk_dev_binded to let
choose the correct method.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fixes the microSD slot on the ASUS C201.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com<mailto:peng.fan@nxp.com>>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
=7i0K
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Use efi_uintn_t where the UEFI spec uses UINTN. Use efi_uintn_t also for
the result of the division of two efi_uintn_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We read the address map before assigning the memory for the pages that will
be mapped to virtual addresses. So these pages will overlap with the entry
for EFI_CONVENTIONAL_MEMORY. We have to ensure that every page is described
at most once in the map.
Remove EFI_CONVENTIONAL_MEMORY from the map that we pass to
SetVirtualAddressMap().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Change the UEFI documentation to Sphinx style and integrate it into the
rest of the Sphinx generated documentation.
Remove the inaccurate TODO list in doc/uefi/uefi.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
make htmldocs produces a warning:
./cmd/efidebug.c:733: WARNING: Unexpected indentation.
Correct the indentation.
Remove 'See above for details of sub-commands.' which is not helpful in the
Sphinx generated documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When changing the architecture without calling 'make clean' a subsequent
make fails with
lib/efi_loader/efi_crt0.o: file not recognized: File format not recognized
Force efi_crt0.o to be always rebuild.
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
