There is no need to define the same macros in drivers.
All macros have been added by commit 17a42abb40 ("mmc: Define timing
macro's").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Freeing a buffer before calling hang() is superfluous. Removing the call
reduces the SPL size.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The driver only needs to retrieve the pin for the ACPI info. The driver
itself works without depending on GPIO.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services
provided by ATF to set SDMMC's DRVSEL and SMPLSEL.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change 'clksel' callback function to allow the code to return a
status.
This patch is a preparation for enabling Arm-Trusted-Firmware (ATF)
in Intel SoC FPGA. This patch does not change functionality.
When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock
related register is secure register which is required to be written
via SMC/PCSI call. It is possible that U-Boot fail to write the
register if there is unexpected error between U-Boot and ATF.
As a result, there maybe signal integrity on MMC connection due to
clock. So, the code should reports error to user when 'clksel' fail.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Define LOG_CATEGORY, use dev_ macro when it is possible.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Currently, when different spi slaves claim the bus consecutively using
spi_claim_bus(), spi_set_speed_mode() will only be executed on the first
two calls, leaving the bus in a bad state starting with the third call.
This patch drops spi_slave->speed member and adds caching of bus
speed/mode in dm_spi_bus struct. It also updates spi_claim_bus() to call
spi_set_speed_mode() if either speed or mode is different from what the
bus is currently configured for. Current behavior is to only take into
account the speed, but not the mode, which seems wrong.
Fixes: 60e2809a84 ("dm: spi: Avoid setting the speed with every transfer")
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reported-by: Moshe, Yaniv <yanivmo@amazon.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Regulator can be set to "always-on".
It's not error about enable/disable. It needs to check about
its condition.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It's useful to know an error number when it's debugging.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400,
db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b ("mmc: fsl_esdhc: support eMMC HS400 mode")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All of the existing quirks add retries to various calls of mmc_send_cmd.
mmc_send_cmd_quirks is a helper function to do this retrying behavior. It
checks if quirks mode is enabled, and if a specific quirk is activated it
retries on error.
This also adds mmc_send_cmd_retry, which retries on error every time
(instead of if a quirk is activated).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If the clock driver does not offer a clk_enable ops, then the system will
return -ENOSYS.
The clk_enable works with CCF (common clock framework).
Some clocks in some cases (like the generic clock for some products: sama5d2)
do not have the clk_enable primitive, and in this case probing of the driver
will fail.
This patch changes the behavior to return an error in case there is really
an error, and not a missing primitive.
If the clock driver does not have an enable primitive, most likely clocks
are always enabled or enabled in the set_rate primitives.
Fixes: 81f16438d4 ("mmc: atmel-sdhci: enable the required generic clock")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Amlogic SM1 SoCs doesn't work over 50MHz. When phase sets to 270', it's
working fine over 50MHz on Amlogic SM1 SoCs.
Since Other Amlogic SoCs doens't report an issue, phase value is using
to 180' by default.
To distinguish which value is used adds an u-boot only sm1 compatible.
In future, it needs to find what value is a proper about each SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Move the asm/arch-meson/sd_emmc.h to a local meson_gx_mmc.h,
remove the useless if/then and fix the meson_gx_mmc.c include.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix the condition to set UHS timings for speeds upto HS200.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define default values for input and output clock phase delays for
Versal. Also define functions for setting tapdelays based on these
clock phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define and use functions for setting input and output tapdelays
based on clk phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define input and output clock phase delays with pre-defined values.
Define arasan_sdhci_clk_data type structure and add it to priv
structure and store these clock phase delays in it.
Read input and output clock phase delays from dt. If these values are
not passed through dt, use pre-defined values.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Just group macros below headers. Other patches will be using this location
too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This reverts commit 942b5fc032.
This is partial revert of the above commit.
mmc_of_parse() is reading no-1-8-v from device tree and if set,
it is clearing the UHS speed capabilities of cfg->host_caps.
cfg->host_caps &= ~(UHS_CAPS | MMC_MODE_HS200 |
MMC_MODE_HS400 | MMC_MODE_HS400_ES);
This is still missing to clear UHS speeds like SDHCI_SUPPORT_SDR104,
SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50.
Even if we clear the flags SDHCI_SUPPORT_XXX in mmc_of_parse(),
these speed flags are getting set again in cfg->host_caps in
sdhci_setup_cfg().
The reason for this is, SDHCI_SUPPORT_XXX flags are cleared
only if controller is not capable of supporting MMC_VDD_165_195 volts.
if (caps & SDHCI_CAN_VDD_180)
cfg->voltages |= MMC_VDD_165_195;
if (!(cfg->voltages & MMC_VDD_165_195))
caps_1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
SDHCI_SUPPORT_DDR50);
It means "no-1-8-v", which is read from DT is not coming in to effect.
So it is better we keep the host quirks(SDHCI_QUIRK_NO_1_8_V) to
clear UHS speeds based on no-1-8-v from device tree.
Hence revert the functionality related to no-1-8-v only, rest is fine
in the patch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
dev_err has been used for debugging and a few dev_err message are
printed for normal code execution. Make them dev_dbg instead.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.
Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove a left-over debug test message from the Octeon TX / TX2
MMC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
