Since B&R boards uses only MMC-Controller #1, it only
wastes time if we initialize #0 first to see that there is nothing.
Cc: <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
FN_SEL_IEB is assigned 2bit, and 2bit can represent 4 patterns.
However FN_SEL_IEB but we only use 3. It adds empty patterns as 0.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Do not do partial bitstream detection based on bitstream
size and use bitstream_type argument which is passed
from the fpga core.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
Apply command "tools/reformat.py -i -d '-' -s 8 <boards.cfg
>boards0.cfg && mv boards0.cfg boards.cfg" in preparation of
pull request from ARM to main tree.
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.
The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4460 differs from B4860 only in number of CPU cores,
hence used existing support for B4860.
B4460 has 2 PPC cores whereas B4860 has 4 PPC cores.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T104xrdb has several sleep management signals that are used for deep
sleep. They are enabled by OS to enter deep sleep and should be
disabled by u-boot when cores wake up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to AN3638, CRC of NXID v1 is at the end of the
256-byte I2C memory. The wrong CRC32 offset prevents Uboot
from reading system information from EEPROM. No NXID v0 is
being used on Freescale boards.
Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
