Add memory and I2C posts to the XPedite517x/520x/537x board families.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PIC's TFRR register doesn't affect hardware and is generally unused,
so use as storage for the POST word.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup. This is useful for cases when a device may or may
not be present, and neither case is considered an error. For example:
- Some form factors such as XMC and Compact PCI Express have an I2C
EEPROM whose address changes based on geographical address. Eg
installed in one slot its EEPROM address is, 0x50, in another its
0x51, etc. This allows multiple devices to have their EEPROMs present
on the same I2C bus. Thus the I2C devices present for an XMC or
CPCIe card depend on if and where other cards are installed in the
same system.
- Some cards have optional I2C devices. Eg one hardware build
configuration has different I2C devices than another and software
can't determine if the optional device should be present or not.
- Some cards have optional daughtercards with I2C devices on them.
- I2C EEPROMs address range depends on their size. Its possible to
support differently size EEPROMs by only probing the EEPROM's base
address and ignoring the other addresses that are impacted by its
size.
A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to the I2C specification device address 0 is the "general call
address", ie a broadcast address. The I2C specification states that the
format of a general call uses at least 2 bytes, which U-Boot's probing
routine does not adhere to.
Not probing device address 0 will prevent possible issues with devices
that accept general calls. Additionally, this change shouldn't reduce
POST coverage since each I2C device should still be accessed via its
own, unique address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The logic previously used in the I2C post was a bit convoluted.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Clean up ifdeffery
- Update coding style
No functional change should have occurred.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some U-Boot images for X-ES boards support multiple products in the same
family. For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards. To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.
While we're at it, change the board config file and make targets to be
lowercase.
Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board_flash_wp_on() to check a pca9557 gpio pin to see
if non-volatile memory write protection is enabled.
Previously, write protected NOR flashes would fail initialization which
resulted in a bootup error such as:
...
DTT: 53 C local / 64 C remote (adt7461@4c)
DTT: 54 C local (ds1621@48)
FLASH: Executed from FLASH1
POST memory PASSED
FLASH: ## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
## Unknown FLASH on Bank 2 - Size = 0x00000000 = 0 MB
*** failed ***
### ERROR ### Please RESET the board ###
With this patch, NOR flash initialization is skipped:
...
DTT: 53 C local / 64 C remote (adt7461@4c)
DTT: 54 C local (ds1621@48)
FLASH: Executed from FLASH1
POST memory PASSED
FLASH: Uninitialized - Write Protect On
L2: 1024 KB enabled
NAND: 1024 MiB
...
Note that flash related commands such as flinfo and saveenv will error
out when flash write protection is enabled.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create a common checkboard() function to support all X-ES's Freescale
boards.
Also, add a get_board_derivative() function which reads hardware
strapping resistors to determine what model a board is. This allows one
U-Boot image to support multiple boards.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a new 'pci enum' command which re-enumerates the PCI buses. This
command is enabled via the CONFIG_CMD_PCI_ENUM define and can be useful
in boards with FPGAs connected via PCI/PCIe, boards that support PCI
hot-plugging, or during PCI debug.
Also enable the 'pci enum' command for X-ES's Freescale-based boards.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Common Freescale code for PCI initialization now exists, so migrate X-ES
boards to use it.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The recent change the env code added an additional 32 bytes into gd_t
and that causes to grow pass the previous CONFIG_SYS_GBL_DATA_SIZE size.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is broken and impossible to repair without deep knowledge or
availability of the hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Add framebuffer driver for the MX51 processor
working on the IPUv3 internal graphic processor.
The port is based on the driver found in the kernel
delivered by Freescale as part of i.MX BSP:
[kernel 2.6.31 commit cc4fe714041805997b601fe8e5dd585d8a99297f]
[agust@denx.de: some style fixes and dead code removal]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The patch is a porting of the IPU Linux driver
developed by Freescale to have framebuffer
functionalities in u-boot. The port is based on
kernel 2.6.31 commit cc4fe714041805997b601fe8e5dd585d8a99297f,
as delivered by Freescale [i.MX BSP].
Most features are dropped from the original driver and
only LCD support is the goal of this porting.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch changes implementation of 'display' command for a4m072
that uses 7-segment LED display as customer requested:
a) The "display" command shall _not_ turn on the decimal point.
b) Exception: "display ." shall turn on (only) the decimal point.
c) Hex digits (0-9, A-F, a-f) shall be displayed as usual.
d) Letters U, P, Y, L, S, T, H shall be displayed as usual (lower
case letters identical to upper case letters)
e) 'I' (and 'i') shall be displayed like '1'
f) 'O' (and 'o') shall be displayed like '0'
g) all other Characters shall be displayed like ' ' (all segments off).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The default values for 'addip' and 'norargs' changed per customer
request. Everything else cleaned up to fit into 80 symbol line.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Commit 29c6fbe047 broke
building for 83xx boards with USB support:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43: error: 'CONFIG_SYS_FSL_USB_ADDR' undeclared (first use in this function)
ehci-fsl.c:43: error: (Each undeclared identifier is reported only once
ehci-fsl.c:43: error: for each function it appears in.)
make[1]: *** [ehci-fsl.o] Error 1
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If a NOR flash is write protected it can not be initialized/detected so
add the ability for boards to skip NOR initialization on bootup. A
board can skip NOR initialization by implementing the
board_flash_wp_on() function.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: sr@denx.de
Acked-by: Stefan Roese <sr@denx.de>
