Commit graph

1288 commits

Author SHA1 Message Date
Ladislav Michl
18cae43b62 mtd: nand: Consolidate nand spl loaders implementation
nand_spl_load_image implementation was copied over into three
different drivers and now with nand_spl_read_block used for
ubispl situation gets even worse. For now use least intrusive
solution and #include the same implementation to nand drivers.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:26 -04:00
Masahiro Yamada
90d6500c0f drivers: remove Blackfin specific drivers
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-04-18 10:29:14 -04:00
Wenyou Yang
0de077df38 mtd: nand: atmel: use another functions to set gpio value
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13 14:44:49 -06:00
Cooper Jr., Franklin
6e1eb089be mtd: nand: am335x_spl_bch: Incorporate tWB delay in nand_command function
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.

Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:34:50 -04:00
Maxime Ripard
ff93c28265 nand: sunxi: Add options for the SPL NAND configuration
The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.

Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Maxime Ripard
adc706b2fe mtd: sunxi: Change U-Boot offset
The default U-Boot offset for the Allwinner SoCs was set to 32kB.

This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.

However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).

We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.

It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.

Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Maxime Ripard
5fe4c9f4d2 mtd: sunxi: Select the U-Boot location config option
We'll need that symbol so that the default offset are defined

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:45 +05:30
Boris Brezillon
aa049152dc mtd: ubi: Select RBTREE option from MTD_UBI Kconfig entry
Expose the RBTREE feature through Kconfig and select this option from the
MTD_UBI option.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[Rebased on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:45 +05:30
Maxime Ripard
ea3f750c73 nand: sunxi: Fix modulo by zero error
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.

In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.

However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.

As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:45 +05:30
Tom Rini
d53ecad92f Merge branch 'master' of git://git.denx.de/u-boot-sunxi
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:40:24 -04:00
Tom Rini
ea3310e8aa Blackfin: Remove
The architecture is currently unmaintained, remove.

Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-05 13:52:01 -04:00
Andre Przywara
7b82a229e5 sunxi: prepare for sharing MACH_SUN8I_H3 config symbol
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
a982bbbc1f SPI: SPL: sunxi: fix 64-bit build
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Stefan Roese
706865afe5 dm: core: Add flags parameter to device_remove()
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.

This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:15:10 -06:00
Hou Zhiqiang
203db38a94 mtd: nand: remove nand size print from nand_init function
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 10:39:33 -07:00
Hou Zhiqiang
d72158c045 mtd: nand: add initialization flag
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 10:38:37 -07:00
Andrey Yurovsky
f78038dc0d mtd: nand: build MXS driver for MX7 as well
The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).

Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.

Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
2017-02-19 16:20:28 +01:00
Masahiro Yamada
e856bdcfb4 flash: complete CONFIG_SYS_NO_FLASH move with renaming
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12 14:30:25 -05:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Ladislav Michl
6fe7fe12cc omap-gpmc: use SECTOR_BYTES instead of hardcoded value
Replace hardcoded value with defined constant SECTOR_BYTES.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-14 16:47:18 -05:00
Tom Rini
0b8404332e Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-01-10 08:19:21 -05:00
Jagan Teki
101000b771 mtd: nand: mxs_nand_spl: Fix to remove twise 'NAND' print
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.

Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB

After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB

Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:56:44 +01:00
Priit Laes
a648936143 spl: sunxi: Fix build error with CONFIG_SPL_SPI_SUNXI
Fix typo introduced in ebc4ef61d7

Signed-off-by: Priit Laes <plaes@plaes.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 11:54:04 +01:00
Cyrille Pitchen
9bcb018870 Revert "sf: Fix quad bit set for micron devices"
This reverts commit c56ae7519f.

Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.

Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.

Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.

Indeed the SPI controller driver is not aware of the SPI protocol switch.

Further patches will fix the support of Micron QSPI memories.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-12-15 18:33:16 +01:00
Phil Edworthy
db9225ba26 sf: Do not force the DT memory map size to exactly match the device
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Fabien Parent
304decdd31 mtd: spi: don't return -1 when scan succeed
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Simon Glass
ebc4ef61d7 spl: Add a name to the SPL load-image methods
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.

The name is only available if we have libcommon support (i.e can use
printf()).

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:13 -05:00
Andre Przywara
58eab3287b mtd: cfi_flash: fix indentation
The indentation is misleading here and suggests that the write command
will be only executed in the else clause.
It seems like this is not intended, so fix the indentation to avoid
both compiler warnings and puzzled readers.

Pointed out by GCC 6.2's -Wmisleading-indentation warning.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-12-04 13:55:01 -05:00
Fabien Parent
cf07d39fb1 NAND: davinci: add support for NAND chips with 16 bits bus
The OMAPL138-LCD board uses a NAND chip with a 16 bits bus. Add
support into the davinci driver for 16 bit bus NAND chips.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:15 -05:00
Boris Brezillon
11777a5ea7 mtd: nand: add support for the TC58NVG2S0H chip
Add the description of the Toshiba TC58NVG2S0H SLC nand to the nand_ids
table so we can use the NAND ECC infos and the ONFI timings.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-11-28 15:10:30 -05:00
Simon Glass
71634f289d spi: Add of-platdata support to SPI and SPI flash
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Radu Bacrau
1f3232d2a1 sf: Add support for MX66U51235F, MX66L1G45G, MT25QU02G, MT25QL02G
This commit adds support for the Macronix MX66U51235F,
MX66L1G45G and Micron MT25QU02G, MT25QL02G flash parts.

Signed-off-by: Radu Bacrau <dumitru.bacrau@intel.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Radu Bacrau <radu.bacrau@gmail.com>
[Update proper commit header and 80-line cut on body]
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-22 11:58:59 +05:30
Andre Przywara
2334c4e705 drivers: SPI: sunxi SPL: fix warning
Somehow an int returning function without a return statement sneaked
in, fix it.
Also fix some whitespace damage on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-21 15:05:08 +05:30
Jagan Teki
94b653b3df sf: Fix s25fs512s id table
s25fs512s and s25fl512s_256k have common id information
till 5 bytes and 6th byte have different family id
like FS and FL-S as 0x81 and 0x80.

Reported-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:54 +05:30
Jagan Teki
25488ec193 sf: dataflash: Minor cleanups
- fix single line comments
- remove unneeded spaces
- ascending order of include files
- rename SPI DATAFLASH to dataflash
- rename SPI DataFlash to dataflash
- return NULL replaced with error code

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:54 +05:30
Jagan Teki
11b93228a7 sf: dataflash: Fix add_dataflash return logic
This patch fixed the add_dataflash return logic,
so-that it can handle both jedec and older chips
same as Linux.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:54 +05:30
Jagan Teki
1835302d3c sf: dataflash: Move flash id detection into jedec_probe
Flash id detection should be the first step to enumerate
the connected flash on the board, once ie done checking
with respective id codes locally in the driver all this
should be part of jedec_probe instead of id detection and
validated through flash_info{} table separatly.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:53 +05:30
Jagan Teki
dc19b06ff2 sf: dataflash: Remove unneeded spi data
dataflash doesn't require options, memory_map from spi.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:53 +05:30
Jagan Teki
20343ff3ad spi: Remove dual flash options/flags
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.

So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-19 08:41:44 +05:30
Jagan Teki
7b4ab88e2d sf: Rename few local functions
spi_flash_write_bar-> write_bar
spi_flash_write_bar -> read_bar
spi_flash_cmd_wait_ready -> spi_flash_wait_till_ready

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-18 13:04:54 +05:30
Jagan Teki
a881374ddb sf: ids: Use small letter in ext_jedec
Use small 'd' in s25s512s ext_jedec

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:54 +05:30
Jagan Teki
7a9b4359cb sf: ids: Use small letter's with flash name
For readability use small letter's with flash name.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:54 +05:30
Jagan Teki
6645fd2c18 sf: Rename sf_params.c to spi_flash_ids.c
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:54 +05:30
Jagan Teki
475bf816f1 sf: Remove non-meaningful comments
Remove unneeded/non-meaningful commit message on
params and flash.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
116e005cfd sf: Remove spansion_s25fss_disable_4KB_erase
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.

To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.

So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.

For this:
- Removed spansion_s25fss_disable_4KB_erase code
- Add SECT_4K for S25FS512S chip

Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
43ecc776ca sf: params: Add S25FS256S_64K spi flash support
Add Spansion S25FS256S_64K spi flash to the list of spi_flash_ids.

In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.

To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.

So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.

Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
8e492951a8 sf: Add INFO6 flash_info macro
INFO6 is for tabulating 6 byte flash parts, Ex: S25FS256S_64K

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
0bdb7cb91f sf: Increase max id length by 1 byte
So, now SPI_FLASH_ID_MAX_LEN is 6 bytes useful for
few spansion flash families S25FS-S

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
ed363b53d0 sf: Add SPI_FLASH_MAX_ID_LEN
Add id length of 5 bytes numerical value to macro.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2016-11-18 13:04:53 +05:30
Jagan Teki
eccb6be068 sf: nr_sectors -> n_sectors
Rename nr_sectors as n_sectors to sync with Linux.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:53 +05:30