Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
We only need to read in the size of struct image_header and thus don't
need to know the page size of the nand device.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
DRAM size should use 64-bit variable when the size could be more than 4GB.
Caught and verified on P4080DS with 4GB DDR.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
We say we have an XIP (in this case, image loaded at desired execution
address) when the image header has been offset in the load. It's
possible that in some cases executing the header is non-fatal but that's
not true in many other cases.
Signed-off-by: Tom Rini <trini@ti.com>
console_buffer array is defined to be CONFIG_SYS_CBSIZE + 1 long,
whereas the_command array only CONFIG_SYS_CBSIZE long. Subsequent
use of strcpy(the_command, console_buffer) will write final \0
terminating byte outside the_command array when entering a command
of max length.
Signed-off-by: Kristian Otnes <kotnes <at> cisco <dot> com>
The command "time" shows the execution time of the command given
to the argument, like this:
time: 45.293 seconds, 45293 ticks
Since we adopted CONFIG_SYS_HZ = 1000 for all boards,
we always have a simple formula: "1 tick = 0.0001 second".
Showing ticks looks almost redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
In the case where an environment variable spans multiple lines, we should
use run_command_list() so that all lines are executed. This shold be
backwards compatible with existing behaviour for existing scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the code for these commands so that they work on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
(Adjusted to fix minor merge comflict, when applied)
Change-Id: I987dee6194cd5c83f82604caf894fc85e4eb71a8
This patch contains an implementation of the fastboot protocol on the
device side and documentation. This is based on USB download gadget
infrastructure. The fastboot function implements the getvar, reboot,
download and reboot commands. What is missing is the flash handling i.e.
writting the image to media.
v3 (Rob Herring):
This is based on http://patchwork.ozlabs.org/patch/126798/ with the
following changes:
- Rebase to current mainline and updates for current gadget API
- Use SPDX identifiers for licenses
- Traced the history and added missing copyright to cmd_fastboot.c
- Use load_addr/load_size for transfer buffer
- Allow vendor strings to be optional
- Set vendor/product ID from config defines
- Allow Ctrl-C to exit fastboot mode
v4:
- Major re-write to use the USB download gadget. Consolidated function
code to a single file.
- Moved globals into single struct.
- Use puts and putc as appropriate.
- Added CONFIG_USB_FASTBOOT_BUF_ADDR and CONFIG_USB_FASTBOOT_BUF_SIZE to
set the fastboot transfer buffer.
v5:
- Add CONFIG option documentation to README
- Rebase using new downloader registration
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds support for the Android boot-image format. The header
file is from the Android project and got slightly alterted so the struct +
its defines are not generic but have something like a namespace. The
header file is from bootloader/legacy/include/boot/bootimg.h. The header
parsing has been written from scratch and I looked at
bootloader/legacy/usbloader/usbloader.c for some details.
The image contains the physical address (load address) of the kernel and
ramdisk. This address is considered only for the kernel image.
The "second image" defined in the image header is currently not
supported. I haven't found anything that is creating this.
v3 (Rob Herring):
This is based on http://patchwork.ozlabs.org/patch/126797/ with the
following changes:
- Rebased to current mainline
- Moved android image handling to separate functions in
common/image-android.c
- s/u8/char/ in header to fix string function warnings
- Use SPDX identifiers for licenses
- Cleaned-up file source information:
android_image.h is from file include/boot/bootimg.h in repository:
https://android.googlesource.com/platform/bootable/bootloader/legacy
The git commit hash is 4205b865141ff2e255fe1d3bd16de18e217ef06a
usbloader.c would be from the same commit, but it does not appear
to have been used for any actual code.
v4:
- s/andriod/android/
- Use a separate flag ep_found to track if the entry point has been set
rather than using a magic value.
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Allow an optional devtype parameter to the ums command, which specifies
the type of the device to be exported. This could allow exporting a SATA
or even another USB device.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
It's easier to assign values to the variables inside an if statement body
if the assignment and declaration are separate.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
get_device() is a generic routine that will support any type of block
device. Use this instead of the type-specific find_mmc_device(), for
future flexibility.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
There's nothing Samsung-/board-specfic about the implementation of
ums_init(). Move the code into cmd_usb_mass_storage.c, so that it can
be shared by any user of that command.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Without this, if g_dnl_register() fails, the UMS code continues on
blindly and crashes. This fix makes it simply print an error message
instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.
I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.
Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.
Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.
CONFIG_USB_CABLE_CHECK was removed.
Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
USB keyboard polling failed for some keyboards on PowerPC 5020.
This was caused by requesting only 4 bytes of data from keyboards that
produce an 8 byte HID report.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch adds a helper function that can be used to interpret most
"ranges" properties in the device tree.
It reads the n'th range out of a "ranges" array and returns the node's
virtual address of the range, the physical address that range starts at
and the size of the range.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We already have a nice helper to give us a property cell value with default
fall back from a path. Split that into two helpers - one for the old path
based lookup and one to give us a value based on a node offset.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MIPS needs a call to timer_init to preserve its current behaviour
ensuring that the cop0 compare register is initialised appropriately.
Reported-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Assigning gd->ram_size the return value of initdram matches the existing
MIPS board behaviour.
Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The LZO decompressor wasn't initializing the maximum output size, which
meant it would fail to decompress most of the time.
Reported-by: Matthias Weißer <weisserm@arcor.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Matthias Weißer <weisserm@arcor.de>
Acked-by: Simon Glass <sjg@chromium.org>
The show_model_r function should return an int but didn't. Return 0 to
indicate inevitable success and avoid the following if it is used:
common/board_r.c: In function 'show_model_r':
common/board_r.c:531:1: warning: no return statement in function returning non-void [-Wreturn-type]
}
^
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
This required moving it into a C file from the header.
The only user of a non-default name_to_gpio is blackfin, therefore build tested
with the blackfin bct-brettl2 build, which is one I picked at random. Also
tested with a build for the ARM tec board which uses the default/fallback
implementation. Inspection with objdump shows that both have done the right
thing.
This change was requested by Marek during review of the sunxi patch series.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Sonic Zhang <sonic.adi@gmail.com>
This patch add support for gpimage format as a preparatory
patch for porting u-boot for keystone2 devices and is
based on omapimage format. It re-uses gph header to store the
size and loadaddr as done in omapimage.c
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
The keystone2 SOC requires to fix all 32 bit aliased addresses
to their 36 physical format. This has to happen after all fdt
nodes are added or modified.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
We add two new environment variables, falcon_args_file and
falcon_image_file, which when set will override the compiled in default
values for falcon mode.
Signed-off-by: Tom Rini <trini@ti.com>
With 452a272 we moved to allocating these variables on the stack. So
they will never now be NULL so remove these checks.
Signed-off-by: Tom Rini <trini@ti.com>
Inside of SPL we only concern ourself with one MMC device, so instead of
being able to use CONFIG_SYS_MMC_ENV_DEV we need to use 0 in SPL.
Switch the code to use a 'dev' variable to facilitate this.
Signed-off-by: Tom Rini <trini@ti.com>
We should move forward to remove the old board init code. Add a
prominent message to encourage maintainers to get started on this
work.
Signed-off-by: Simon Glass <sjg@chromium.org>
We've run into a non-trivial conversion to CONFIG_SYS_GENERIC_BOARD so
we'll postpone this notice until right after v2014.04 is out.
This reverts commit 36c4b1d980.
Signed-off-by: Tom Rini <trini@ti.com>
Changes:
- randomly generate partition uuid if any is undefined and CONFIG_RAND_UUID
is defined
- print debug info about set/unset/generated uuid
- update doc/README.gpt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
We should move forward to remove the old board init code. Add a
prominent message to encourage maintainers to get started on this
work.
Signed-off-by: Simon Glass <sjg@chromium.org>
When using CONFIG_SYS_I2C i2c needs to be initialized by
i2c_init_all(). This is done in some places but not in
eeprom_init().
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
I needed to be able to uncompress lzma files. I did this command
based on unzip command and propose it if it could help.
Signed-off-by: Patrice Bouchand <pbfwdlist@gmail.com>
Changed to work with sandbox
Signed-off-by: Simon Glass <sjg@chromium.org>
Add function which allows encrypting the whole environment block with
AES-128-CBC. The key for the environment is retrieved by
env_aes_cbc_get_key() function, which must be implemented on a per-board
basis.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement env_export() wrapper, so that all implementers of saveenv() don't
have to call hexport_r(), crc32() etc. sequence . This trims down a bit of
code duplication.
Signed-off-by: Marek Vasut <marex@denx.de>
Add simple 'aes' command, which allows using the AES-128-CBC encryption
and decryption functions from U-Boot command line.
Signed-off-by: Marek Vasut <marex@denx.de>
add host tool "fit_check_sign" which verifies, if a fit image is
signed correct.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Add hash_init(), hash_update() and hash_finish() to the
hash_algo struct. Add hash_lookup_algo() to look up the
struct given an algorithm name.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for sha256,rsa4096 signatures in u-boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: andreas@oetken.name
based on patch from andreas@oetken.name:
http://patchwork.ozlabs.org/patch/294318/
commit message:
I currently need support for rsa-sha256 signatures in u-boot and found out that
the code for signatures is not very generic. Thus adding of different
hash-algorithms for rsa-signatures is not easy to do without copy-pasting the
rsa-code. I attached a patch for how I think it could be better and included
support for rsa-sha256. This is a fast first shot.
aditionally work:
- removed checkpatch warnings
- removed compiler warnings
- rebased against current head
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: andreas@oetken.name
Cc: Simon Glass <sjg@chromium.org>
check if a fdt is correct signed
pass an optional addr value. Contains the addr of the key blob
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add a simple LCD driver which uses SDL to display the image. We update the
image regularly, while still providing for reasonable performance.
Adjust the common lcd code to support sandbox.
For command-line runs we do not want the LCD to be displayed, so add a
--show_lcd option to enable it.
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a common library for obtaining access to the Chrome OS EC. This is
used by boards which need to talk to the EC.
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Tested-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use U-Boot's filesystem layer to read the sandbox device tree,
but this is problematic since it relies on a temporary feauture added
there. Since we plan to implement proper block layer support for sandbox,
change this code to use the os layer functions instead. Also use the new
fdt_create_empty_tree() instead of our own code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
When importing a checksummed area we need to be told how big the area in
question is so that we know that will match the size of the area which
the checksum is generated against.
Reported-by: Pierre AUBERT <p.aubert@staubli.com>
Signed-off-by: Tom Rini <trini@ti.com>
The following shell command fails:
if test -z "$x"; then echo "zero"; else echo "non-zero"; fi
(assuming $x does not exist, it prints "non-zero" rather than "zero").
... since "$x" expands to nothing, and the argument is completely
dropped, causing too few to be passed to -z, causing cmd_test() to
error out early.
This is because when variable expansions are processed by make_string(),
the expanded results are concatenated back into a new string. However,
no quoting is applied when doing so, so any empty variables simply don't
generate any parameter when the combined string is parsed again.
Fix this by explicitly replacing quoting any argument that was originally
quoted when re-generating a string from the already-parsed argument list.
This also fixes loss of whitespace in commands such as:
setenv space " "
setenv var " 1${space}${space} 2 "
echo ">>${var}<<"
Reported-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add 64-bit data for memory commands, such as md, mw, mm, cmp. The new
size ".q " is introduced.
For 64-bit architecture, 64-bit data is enabled by default, by detecting
compiler __LP64__. It is optional for other architectures.
Signed-off-by: York Sun <yorksun@freescale.com>
Now that named GPIO banks are supported, along with a way of obtaining
the status of a GPIO (input or output), we can provide an enhanced
GPIO command for driver model. Where the driver provides its own operation
for obtaining the GPIO state, this is used, otherwise a generic version
is sufficient.
Signed-off-by: Simon Glass <sjg@chromium.org>
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.
To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.
The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Make driver model available after relocation, by setting up data structures
and scanning for devices using compiled-in platform_data and (when available)
the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot now uses errors defined in include/errno.h which are negative
integers. Commands which fail need to report the error and return 1
to indicate failure. Add this functionality in cmd_process_error().
For now this merely reports the error number. It would be possible
also to produce a helpful error message by storing the error strings
in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level. We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.
To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@ti.com>
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
There was no enough stack in SPL, so the buffer needed in SPL is to malloc
from memory pool and to repalce the temporary variable.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For aarch64, unsigned long is 64-bit data. Memory commands should be fixed
with u32 for 32-bit address access. To be clear, ushort is replace with
u16, u_char is replaced with u8.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
The directory name from an fdtdir directive in a PXE config file should
always be pre-pended to the DTB filename; it shouldn't matter whether
the DTB filename came from the $fdtfile environment variable, or whether
it was constructed dynamically from ${soc}-${board}.dtb. Fix the code to
always prepend the directory name.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Fixes: c61d94d860 ("pxe: implement fdtdir extlinux.conf tag")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
This patch deal with error message of mtest command.
When test failed, the mtest command will output error information
that include memory address and value. But the address field is
not correct or misleading.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This function has been around for powerpc. It is used for systems with
memory more than CONFIG_MAX_MEM_MAPPED. In case of non-contiguous memory,
this feature can limit U-boot to one block without going over the limit.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
do_bootm_standanlone() calls ntohl(images->ep) which is wrong because
endianess conversion has already been done:
do_bootm()
\-do_bootm_states()
+-bootm_find_os()
| \-images.ep = image_get_ep();
| \-uimage_to_cpu(hdr->ih_ep);
\-boot_selected_os()
\-do_bootm_standanlone()
Without this conversion the code works correctly at least on AT91SAM9G45.
On big endian systems there should be no difference after applying this
patch because uimage_to_cpu(x) and ntohl(x) both expand to 'x'.
Signed-off-by: Christian Eggers <ceggers@gmx.de>
pxe.c provides both the "pxe" command which relies on a network, and the
"sysboot" command which doesn't. Fix the file to compile when network
support isn't enabled. This is useful e.g. on the Raspberry Pi which has
no network support yet, but will soon support the sysboot command.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
There is a strange comment in fit_image_load().
This function can be used for loading Kernel Image, FDT
as well as ramdisk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Useful rules in scripts/Makefile.lib allows us to easily
generate a device tree blob and wrap it in assembly code.
We do not need to parse a linker script to get output format and arch.
This commit deletes ./u-boot.dtb since it is a copy of dts/dt.dtb.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Unlike other commands (for example, "fatwrite"), ext4write would
interpret the "sizebytes" as decimal number. This is not only
inconsistend and unexpected to most users, it also breaks usage
like this:
tftp ${addr} ${name}
ext4write mmc 0:2 ${addr} ${filename} ${filesize}
Change this to use the standard notation of base 16 input format.
See also commit b770e88
WARNING: this is a change to the user interface!!
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Uma Shankar <uma.shankar@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
This is much like a regular shell's -e operator, except that it takes
multiple arguments to specify the device type and device/partition ID
in addition to the usual filename:
if test -e mmc 0:1 /boot/boot.scr; then echo yes; else echo no; fi
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This emulates bash:
$ if test; then echo yes; else echo no; fi
no
Currently, the code sets expr = -1 in this case, which gets mapped to
0 (true) at the end of do_test() by the logical -> shell exit code
conversion.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Currently, ! can only be parsed as the first operator in an expression.
This prevents the following from working:
$ if test ! ! 1 -eq 1; then echo yes; else echo no; fi
yes
$ if test ! 1 -eq 2 -a ! 3 -eq 4; then echo yes; else echo no; fi
yes
Fix this by parsing ! like any other operator, and and handling it
similarly to -a and -o.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This better mirrors the behaviour of bash, for example:
$ if test -z = -z; then echo yes; else echo no; fi
yes
This is parsed as a string comparison of "-z" and "-z", since the check
for the binary "=" operator occurs first. Without this change, the
command would be parsed as a -z test of "-", followed by a syntax error;
a trailing -z without and operand.
This is a behavioural change, but I believe any commands affected were
previously invalid or bizarely formed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
do_test() currently uses strcmp() twice to determine which operator is
present; once to determine how many arguments the operator needs, then
a second time to actually decode the operator and implement it.
Rewrite the code so that a table lookup is used to translate the operator
string to an integer, and use a more efficient switch statement to decode
and execute the operator.
This approach also acts as enablement for the following patches.
This patch should introduce no behavioural change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rename 'bootpart' to 'bootpart-resize' to better reflect what this
command is for.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions. Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
People who write (or scripts that auto-generate) extlinux.conf don't
want to know about HW-specific information such as FDT filenames. Create
a new extlinux.conf tag "fdtdir" that specifies only the directory where
FDT files are located, and defer all knowledge of the filename to U-Boot.
The algorithm implemented is:
==========
if $fdt_addr_r is set:
if "fdt" tag was specified in extlinux.conf:
load the FDT from the filename in the tag
else if "fdtdir" tag was specified in extlinux.conf:
if "fdtfile" is set in the environment:
load the FDT from filename in "$fdtfile"
else:
load the FDT from some automatically generated filename
if no FDT file was loaded, and $fdtaddr is set:
# This indicates an FDT packaged with firmware
use the FDT at $fdtaddr
==========
A small part of an example /boot/extlinux.conf might be:
==========
LABEL primary
LINUX zImage
FDTDIR ./
LABEL failsafe
LINUX bkp/zImage
FDTDIR bkp/
==========
... with /boot/tegra20-seaboard.dtb or /boot/bkp/tegra20-seaboard.dtb
being loaded by the sysboot/pxe code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The specification for extlinux.conf[1] states that "fdt" is an alias for
"devicetree". To date, U-Boot only implements "fdt". Rectify that.
[1] http://freedesktop.org/wiki/Specifications/BootLoaderSpec/
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Command provides just dump subcommand for showing clock
frequencies in a soc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Changes:
- le16_to_cpu() to get_unaligned_le16()
- le32_to_cpu() to get_unaligned_le32()
when access fields in struct bmp header.
This changes avoids data abort exception caused by unaligned data access.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is only required for "PIC" relocation and doesn't apply to modern
"PIE" relocation which does data relocation as well as code.
"init_sequence_r" is just an array that consists of compile-time
adresses of init functions. Since this is basically an array of integers
(pointers to "void" to be more precise) it won't be modified during
relocation - it will be just copied to new location as it is.
As a consequence on execution after relocation "initcall_run_list" will
be jumping to pre-relocation addresses. As long as we don't overwrite
pre-relocation memory area init calls are executed correctly. But still
it is dangerous because after relocation we don't expect initially used
memory to stay untouched.
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Thomas Langer <thomas.langer@lantiq.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
The change to add 64bit initrd support broke 32bit initrd support as it
always set 64bits worth of data into the properties, even on 32bit
systems. The fix is to use addr_cell_len (which already says how much
data is in 'tmp') to set the property, rather than always setting 8.
Thanks to Stephen Warren for pointing out the fix here.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@ti.com>
when creating the hashtable, for each environmentvariable
getenv(ENV_CALLBACK_VAR) and getenv(ENV_FLAGS_VAR) is called,
which costs at this point a lot of time. So call this two
getenv() calls only once.
Boottime on the ids8313 board without this patch:
2013-12-19 13:38:22,894: NAND: 128 MiB
2013-12-19 13:38:27,659: In: serial
(~4.8 sec)
Bootime with this patch on the ids8313 board:
2013-12-19 13:40:25,332: NAND: 128 MiB
2013-12-19 13:40:25,546: In: serial
(~0.2 sec)
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wolfgang Denk <wd@denx.de>
For standalone images, bootm had a special case where the OS boot function
was NULL but did actually exist. It was just called manually.
This was removed by commit 35fc84fa which checks for the non-existence of
this function before the special case is examined.
There is no obvious reason why standalone is handled with a special case.
Adjust the code so that standalone has a normal OS boot function. We still
need a special case for when the function returns, but at least we can
avoid the main problem.
This is intended to fix the reported:
ERROR: booting os 'U-Boot' (17) is not supported
but needs testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Otherwise, when booting VxWorks kernel, the incorrect message will
be seen:
ARM Unknown OS Kernel Image (uncompressed)
Signed-off-by: Miao Yan <miao.yan@windriver.com>
Compiling of full list of commands does not advance the counter,
so it always results in an empty list.
This seems to be (inadvertently?) introduced by commit
6c7c946cad.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Before this change ums mode can not be entered when device
was using the same usb port for usb/uart communication.
Switching USB cable from UART to USB always causes ums exit.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
"env_eeprom_bus" is no longer in use (it was introduced in commit
548738b4d4 "cmd_eeprom: I2C updates").
As in "eeprom_bus_write" we just reset I2C bus with the one we saved in
"old_bus".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Add map_sysmem() calls so that this test works correctly on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
Relocation code based on a patch by Scott Wood, which is:
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Feng <fenghua@phytium.com.cn>
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
It is useful to be able to save and restore the RAM contents of sandbox
U-Boot either for setting up tests, for later analysys, or for chaining
together multiple tests which need to keep the same memory contents.
Add a function to provide a memory file for U-Boot. This is read on
start-up and written when shutting down. If the file does not exist
on start-up, it will be created when shutting down.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
With sandbox, errors and problems may be reported before console_init_f()
is executed. For example, an argument may not parse correctly or U-Boot may
panic(). At present this output is swallowed so there is no indication what
is going wrong.
Adjust the console to deal with a very early sandbox setup, by detecting that
there is no global_data yet, and calling os functions in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The execution flow becomes easier if we can return from board_init_f()
as ARM does. We can control things from start.c instead of having to
call back into that file from other places.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to use any host file or device as a block device in U-Boot.
This can be used to provide filesystem access within U-Boot to an ext2
image file on the host, for example.
The support is plumbed into the filesystem and partition interfaces.
We don't want to print a message in the driver every time we find a missing
device. Pass the information back to the caller where a message can be printed
if desired.
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
- Removed change to part.c get_device_and_partition()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdt_fixup_memory_banks() will add and update /memory node in
device tree blob. In the case that /memory node doesn't exist,
after adding a new one, this function returns error.
The correct behavior should be continuing to update its properties.
Signed-off-by: Miao Yan <miao.yan@windriver.com>
The next version VxWorks adopts device tree (for PowerPC and ARM) as its hardware
description mechanism. For PowerPC, the boot interface conforms to
the ePAPR standard, which is:
void (*kernel_entry)(ulong fdt_addr,
ulong r4 /* 0 */,
ulong r5 /* 0 */,
ulong r6 /* EPAPR_MAGIC */, ulong r7 /* IMA size */,
ulong r8 /* 0 */, ulong r9 /* 0 */)
For ARM, the boot interface is:
void (*kernel_entry)(void *fdt_addr)
Signed-off-by: Miao Yan <miao.yan@windriver.com>
[trini: Fix build error when !CONFIG_OF_FDT is set, typo on PowerPC,
missing extern ft_fixup_num_cores]
Signed-off-by: Tom Rini <trini@ti.com>
do_bootm_vxworks now is available under the configuration option
CONFIG_BOOTM_VXWORKS, thus aligned with other operating systems
that supported by bootm command. The bootvx command still depneds
on CONFIG_CMD_ELF.
Signed-off-by: Miao Yan <miao.yan@windriver.com>
If U-Boot build with DEBUG enabled/defined the first call of "debug"
function (that dumps data to any available console) will happen before
zeroing of initial "gd" in init call "zero_global_data" in
"init_sequence_f".
And if stack was not filled with zeros chances are high that
"gd->have_console" won't be 0. In its turn it will cause attempt to
output things to non-initialized yet serial console.
So for safety and predictability we set "gd->have_console = 0".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
argv[0] contains bootvx (command name) not the load address, if called with
argv < 2 use load_addr, else use address argument given to the command.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>
The documentation suggested the arguments where passed over r3-r6
while the code below simply does that over r0-r3.
Cc: Kumar Gala <galak@kernel.crashing.org>
The local pointer of address (i.e., addr) only gets
referenced under SPI mode, and it won't be appropriate
to pass only 1-byte addr[1] to i2c_read/i2c_write while
CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 1.
1. In U-boot's I2C model, the address would be re-assembled
to a byte string in MSB order inside I2C controller drivers.
2. The 'CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW' option which could
be found at soft_i2c.c is always turned on in cmd_eeprom.c,
the addr[0] always contains the device address with overflowed
MSB address bits.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
The directory tools/ is always built before common/.
So when envcrc tool is necessary in common/Makefile,
it already exists.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In the case of not having CONFIG_CMD_HASH but having CONFIG_CMD_CRC32
enabled (and not CONFIG_CRC32_VERIFY), we end up in this part of the
code path on hash_command(). However, we will only have exactly 3 args
here, and 3 > 3 is false, and we will not try and store the hash at the
address given as arg #3. The next problem however is that we've been
moving argv around so the third value is now in argv[0] not argv[3].
Confirmed on AM335x Beaglebone White.
Signed-off-by: Tom Rini <trini@ti.com>
Some phys (Micrel) have additional registers that can
be accessed using a special sequence. This patch allows
to use standard "mdio" command to accesss these registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Data "offset" is not used directly in case of I2C EEPROM. Istead it is
split into "block number" and "offset within mentioned block". Which are
"addr[0]" and "addr[1]" respectively.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Remove the redundant lcd_line_length initialisation which
sneaked in when an earlier version of the patch of commit
6d330719 has been rebased.
Some lcd drivers need to setup lcd_line_length not from the
panel_info parameters but by different means. Make the
lcd_get_size() weak to allow setting lcd_line_length in
a driver specific way.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
The env export command doesn't export the first variable of the list
since commit 5a31ea04c9
"env grep" - reimplement command using hexport_r()
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
The gpt command was only implemented for mmc devices. There is no reason
why this command should not be generalized and be applied all other
storage device classes.
This change both simplifies the implementation and eliminates a
build failure for systems that don't support mmcs.
Signed-off-by: Egbert Eich <eich@suse.com>
Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
[trini: Change coding style slightly]
Signed-off-by: Tom Rini <trini@ti.com>
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Before this change ums command only allowed use of mmc 0.
Now this argument can be set.
Changes:
- remove mmc device number checking because it is always positive number
- remove printing "no such device" - it is done by find_mmc_device()
Change-Id: I767e45151ad515c7bef19e6c13087374f5e23c11
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
In commit "5c427e4: use BOOTM_STATE_OS_CMDLINE flag for plain bootm"
and "3d187b3: Only pass BOOTM_STATE_OS_CMDLINE on PowerPC/MIPS",
BOOTM_STATE_OS_CMDLINE was added to do_bootm for PowerPC and MIPS. This
breaks other OSes (vxworks, netbsd, plan9,...) that don't support
subcommand processing, e.g. they all contain the following code in their
do_bootm_xxx():
if (flag & BOOTM_STATE_OS_PREP)
return 0;
if ((flag != 0) && (flag != BOOTM_STATE_OS_GO))
return 1;
which will result a "subcommand not supported" error.
This patch changes the above logic to:
/* if not go command, pretend everything to be OK */
if (flag != BOOTM_STATE_OS_GO)
return 0;
Signed-off-by: Miao Yan <miao.yan@windriver.com>
env exists is a way to test (in hush) if an environment variable
exists. A workaround existed using printenv but this new command
doesn't require all the stdout/stderr redirection to prevent
printing information to the screen.
Example:
$ set testexists 1
$ env exists testexists && echo "yes"
yes
$ env exists testexists || echo "no"
$ set testexists
$ env exists testexists && echo "yes"
$ env exists testexists || echo "no"
no
$
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Here is the set of command which has been performed
to proof this feature.
gzip < fpga.bin > fpga.bin.gz
mkimage -A arm -O u-boot -T firmware -C gzip \
-a 20000000 -n "zc702_fpga_bin" -d fpga.bin.gz fpga.bin.gz.ub
tftp 100000 fpga.bin.gz.ub
fpga loadmk 0 100000
This flow should speedup loading bitstream data
from external memory and save image footprint in non volatile
memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
pxelinux and syslinux differ in their handling of absolute paths in menu
files. A pxelinux path is aways prepended with the bootfile path while
syslinux allows for absolute paths. u-boot was always treating a leading
/ as an absolute path breaking some pxelinux setups. Fix this by adding
a flag to distinguish pxelinux vs. syslinux behavior.
Reported-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This will be used by usb_lowlevel_init so it will
no longer be used by only board specific functions.
Move definition of enum usb_init_type higher in file
so that it will be available for usb_low_level_init.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
New command - thordown - has been added to support downloading data
via lthor TIZEN program.
It is similar to dfu command syntax and reuses its code for flashing data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
On generic board, the i2c init initialize only
one bus. But the new i2c subsystem allow to
manage severals i2c bus. So in the case, instead
of initializing a bus, we just set the current
i2c bus. The initialization will be done in
the i2c command.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
This bug was introduced by:
"Add GPL-2.0+ SPDX-License-Identifier to source files"
(sha1: 1a4596601f)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
commit 39ac34473f ("cmd_mtdparts: use 64
bits for flash size, partition size & offset") introduced warnings
in a couple places due to printf formats or pointer casting.
This patch fixes the warnings pointed out here:
http://lists.denx.de/pipermail/u-boot/2013-October/164981.html
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tom Rini <trini@ti.com>
Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to
avoid possible crashes due to null pointer dereferencing.
Commit d7884e047d does not go far enough.
There is still at least one call chain that can result in a crash.
The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid
cmdtp. Passing in NULL is particularly bad in the do_tftpb() case,
because eventually boot_get_kernel() will be called with a NULL cmdtp:
do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm()
-> do_bootm_states() -> bootm_find_os() -> boot_get_kernel()
Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the
null pointer, and the board will crash.
Signed-off-by: Steven A. Falco <stevenfalco@gmail.com>
commit d196bd8803 adds
redundand environment to mmc. The usage of malloc in
env_relocate_spec triggers cache errors on armv7.
Tested on a not mainlined i.MX53 board:
Board: TQMa53
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57c2d8
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f57e2d8
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57e2e0
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f5802e0
Using default environment
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
As the SPI controller is not initialized before env_init(), it causes
reading env in dataflash failed. So, although saveenv() successfully,
it shows warning information when reboot the system as following:
*** Warning - bad CRC, using default environment
Let the env_relocate() to check env CRC and import it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This allows you to write data to an UBI volume when the amount of memory
available to write that data from is less than the total size of the
data. For example, you may split a root filesystem UBIFS image into
parts, provide the total size of the image to the first write.part
command and then use multiple write.part commands to write the
subsequent parts of the volume. This results in a sequence of commands
akin to:
ext4load mmc 0:1 0x80000000 rootfs.ubifs.0
ubi write.part 0x80000000 root 0x08000000 0x18000000
ext4load mmc 0:1 0x80000000 rootfs.ubifs.1
ubi write.part 0x80000000 root 0x08000000
ext4load mmc 0:1 0x80000000 rootfs.ubifs.2
ubi write.part 0x80000000 root 0x08000000
This would write 384MiB of data to the UBI volume 'root' whilst only
requiring 128MiB of said data to be held in memory at a time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
int64_t matches the bytes field in struct ubi_mkvol_req to which the
size is assigned. With the prior signed 32 bit integer, volumes were
restricted to being less than 2GiB in size.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
This matches the 64 bit size in struct mtd_info and allows the mtdparts
command to function correctly with a flash >= 4GiB. Format specifiers
for size & offset are given the ll length, matching its use in
drivers/mtd in absence of something like inttypes.h/PRIx64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
As documented, almost all U-Boot commands expect numbers to be entered
in hexadecimal input format. (Exception: for historical reasons, the
"sleep" command takes its argument in decimal input format.)
This rule was broken for the "load" command; for details please see
especially commits 045fa1e "fs: add filesystem switch libary,
implement ls and fsload commands" and 3f83c87 "fs: fix number base
behaviour change in fatload/ext*load". In the result, the load
command would always require an explicit "0x" prefix for regular
(i. e. base 16 formatted) input.
Change this to use the standard notation of base 16 input format.
While strictly speaking this is a change of the user interface, we
hope that it will not cause trouble. Stephen Warren comments (see
[1]):
I suppose you can change the behaviour if you want; anyone
writing "0x..." for their values presumably won't be
affected, and if people really do assume all values in U-Boot
are in hex, presumably nobody currently relies upon using
non-prefixed values with the generic load command, since it
doesn't work like that right now.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/171172
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The part_validate comment had a wrong description of the actions it
does and referenced to non-existent functions while in fact it calls
'part_validate_eraseblock()'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Only the <linux/usb/gadget.h> requires error.h include. Hence, several
includes of error.h at USB gadget functions are not needed.
Moreover unnecessary malloc.h includes were also removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New dfu_init_env_entities() function has been extracted from cmd_dfu.c and
stored at dfu core.
This is a dfu centric code, so it shall be processed in the core.
Change-Id: I756c5de922fa31399d8804eaadc004ee98844ec2
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
When we call do_bootm() with a vmlinuz, this would lead to a NULL
pointer dereference, and after talking with Wolfgang the right thing to
do here for now is to make sure that we pass cmdtp to these functions
rather than NULL.
Reported-by: Steven A. Falco <stevenfalco@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
In 5c427e4 we pass BOOTM_STATE_OS_CMDLINE as part of the bootm states to
run, on all arches. However, this is only valid / useful on PowerPC and
MIPS, and causes a problem on ARM where we specifically do not use it.
Rather than make this state fake pass like we do for GO on some arches
(which need updating to use the GO state), we should just not pass
CMDLINE except when it may be used, like before.
Tested-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
