AXP_PMIC_BUS enables communication with a specific AXP PMIC at a
PMIC-dependent I2C/P2WI/RSB bus address. It is automatically selected
as a dependency of the PMIC driver. It should not be selectable by the
user when no PMIC is chosen.
AXP_GPIO uses the pmic_bus functions, and also depends on a specific
PMIC header to pick up register definitions.
Both of these changes have no impact on any existing configs, since
the code does not compile if the dependencies are not met.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
SUN8I_RSB should not be selected by MACH_SUN8I, because the hardware
is not present in half of those SoCs (H3/H5, R40, and V3s). Move the
selection to the SoCs where the hardware actually exists.
As it currently stands, selecting that option also requires using it in
some way, which is not the case for one A80 board. Since we have only
three A80 boards in total, we select it their via their defconfigs.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixing up Sunchip_CX-A99 build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level
Kconfig symbol (not specific to either legacy or DM I2C), whereas the
i2c_init() function is specific to legacy I2C. This change fixes a
build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-by: Andre Przywara <andre.przywara@arm.com>
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.
Original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The macro called MUX_VAL generates a writel instruction with
semicolon at the end. This table was written to use semicolons,
however one was missed:
MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */
Since the extra semicolon is unnecessary with the use of the macro,
remove all of them, and cleanup whitespace.
Reviewed-by: Wolfgang Denk <wd@denx.de>
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
There are five omap3 based boards from LogicPD. Two of them
have added LTO support. Add the remaining three to use LTO.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This clarifies which callers must be updated to complete the DM_GPIO
conversion.
The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit enables the green status LED (PD18/GPIO 114) on boot in the
SPL, in order to provide visual feedback that the PinePhone is booting.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.
In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The PineTab device-tree is already in u-boot, this commit adds the
corresponding defconfig, based on pinephone_defconfig.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM_VIDEO conversion the 'vidconsole' is the correct name
for the frame buffer console. 'video' will not work, so update
the description of the config option.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert pixel values when necessary like we do for 16bpp
framebuffers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the FDT into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use boolean variables to deal with the strange #ifdef logic of this
function, so we can remove the #ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the ramdisk into a separate function.
Leave the code indented as it was for easier review. The next patch cleans
this up along with checkpatch violations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present EFI_SECURE BOOT selects RSA but does not necessarily enable
FIT_SIGNATURE. Mostly this is fine, but a few boards do not enable it,
so U-Boot tries to do RSA verification when loading FIT images, but it
is not enabled.
This worked because the condition for checking the RSA signature is
wrong in the fit_image_verify_with_data() function. In order to fix it
we need to fix this dependency. Make sure that FIT_SIGNATURE is enabled
so that RSA can be used.
It might be better to avoid using 'select' in this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
