Use versioned URLs for line numbers as branches are moving in the time and
use master branch for mv-ddr-marvell where is up-to-date code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Use function mmc_get_op_cond() instead of mmc_init() for detecting presence
of eMMC. Documentation for this function says that it could be used to
detect the presence of SD/eMMC when no card detect logic is available.
This function is also used by mx6cuboxi board for detecting presence of eMMC.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Ensure that 'env default -a' always set correct value to $fdtfile, even
when custom user variable is already stored in non-volatile env storage
(means that env_get("fdtfile") call returns non-NULL value).
As default value is now correctly set like if specified at compile time in
CONFIG_EXTRA_ENV_SETTINGS, there is no need to set $fdtfile explicitly via
env_set("fdtfile", ...) call.
So remove wrong skip based on env_get("fdtfile") and then also unneeded
env_set("fdtfile", ...) call.
Fixes: c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.
This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.
This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.
This change also ensure that 'env default -a' set correct value to $fdtfile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Try to initialize emmc in board_late_init() and if it fails then we know
that emmc device is not connected.
This allows to use in U-Boot just one DTS file for all Espressobin variants
and also to correctly set fdtfile env variable for Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Fix the actual board vendor and ease synching dts files from Linux.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The patches changing the compatible strings to the ones used by Linux have
not been merged yet, so fix the checks to use the current in-tree ones.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Required for the generic distro mechanism.
Linux ships with 4 variants:
marvell/armada-3720-espressobin-v7-emmc.dtb
marvell/armada-3720-espressobin-v7.dtb
marvell/armada-3720-espressobin-emmc.dtb
marvell/armada-3720-espressobin.dtb
Use available information to determine the appropriate filename.
Fixes booting GRUB EFI arm64 on Fedora.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Due to different partition layouts in different U-Boot versions, DTS for
Espressobin in Linux does not contain any definition of MTD partitions.
See commit https://git.kernel.org/stable/c/00954566464a4 for more details.
This patch via ft_board_setup() hook fills current partition layout used by
U-Boot, so booted kernel would see correct MTD partitions layout.
U-Boot env partition is calculated from CONFIG_ENV_OFFSET option.
First partition contains secure firmware, ARM trusted firmware and U-Boot
with checksums. So it is not possible to replace just one image (e.g.
U-Boot) without updating other parts where is stored checksum of U-Boot.
Therefore there is no extra partition defined for U-Boot and first
partition is called just 'firmware'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
By default Topaz switch on Espressobin board forwards packets between all
ethernet ports, including CPU (port 0), wan (port 1) and lan (ports 2,3).
This default U-Boot setup is unsuitable for using Espressobin as router as
it opens security hole in forwarding all packets between wan and lan ports.
E.g. dhcp packets from wan network leaks to lan network during small time
window until U-Boot boots Linux kernel which loads network drivers which
disallows forwarding between wan and lan.
This patch fixes above problem. For Espressobin board prior putting Topaz
switch into forwarding mode, Topaz switch is reconfigured to allow
forwarding packets from wan and lan ports only to CPU port. This ensures
that packets from wan port are not forwarded to lan ports and vice-versa.
Packets from CPU port are still forwarded to all other ports, so U-Boot
network boot works with any ethernet port as before.
This problem was already discussed on Espressobin forum [1] and on
Marvell's github issue tracker [2]. As a workaround people on Espressobin
forum patched U-Boot to completely disable lan ports on Topaz switch which
prevented forwarding packets. That workaround had an issue that U-Boot was
unable to netboot via lan ports anymore. Change in this patch does not have
such issue.
This security issue has been dicussed here as well: [3].
[1] - https://web.archive.org/web/20191231164238/http://espressobin.net/forums/topic/boot-behavior-of-the-switch-and-security/
[2] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/issues/18
[3] - https://forum.armbian.com/topic/12635-espressobin-uboot-security-concerns-switch-init-portmask/
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the new pinctrl/gpio driver is used, so this patch removes
the old board specific pin control settings.
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-23 08:50:50 +01:00
Renamed from board/Marvell/mvebu_db-88f3720/board.c (Browse further)
