Add iMX8ULP DDR initialization driver which loads the DDR timing
parameters and executes the training procedure.
When enabling IMX8ULP_DRAM_PHY_PLL_BYPASS, using PHY PLL bypass mode
to do DDR init
Signed-off-by: Ye Li <ye.li@nxp.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With gcc-11 we see:
drivers/ddr/marvell/a38x/ddr3_debug.c:672:47: error: argument 2 of type 'u32[5]' {aka 'unsigned int[5]'} with mismatched bound [-Werror=array-parameter=]
672 | int ddr3_tip_read_adll_value(u32 dev_num, u32 pup_values[MAX_INTERFACE_NUM * MAX_BUS_NUM],
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ddr/marvell/a38x/ddr3_training_ip_engine.h:10,
from drivers/ddr/marvell/a38x/ddr3_init.h:17,
from drivers/ddr/marvell/a38x/ddr3_debug.c:6:
drivers/ddr/marvell/a38x/ddr3_training_ip_flow.h:116:47: note: previously declared as 'u32[]' {aka 'unsigned int[]'}
And similar warnings. Correct these by updating the prototype. Remove
the prototype for ddr3_tip_read_pup_value as it is unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS
Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config option ARMADA_39X is never set so remove all dead code hidden under
ifdef CONFIG_ARMADA_39X blocks.
Also remove useless checks for CONFIG_ARMADA_38X define as this macro is
always defined for a38x code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The arrays `pbs_dq_mapping`, `div_ratio1to1` and `div_ratio2to1` have
different bounds declared in header files where these variables are also
defined from the ones declared in source files.
This causes the compiler to complain (when building with LTO):
ddr3_sdram.c:24:12: warning: type of ‘pbs_dq_mapping’ does not match
original declaration
[-Wlto-type-mismatch]
ddr3_patterns_64bit.h:911:5: note: array types have different bounds
ddr3_patterns_64bit.h:911:5: note: ‘pbs_dq_mapping’ was previously
declared here
ddr3_dfs.c:45:11: warning: type of ‘div_ratio1to1’ does not match
original declaration [-Wlto-type-mismatch]
ddr3_axp_vars.h:167:4: note: array types have different bounds
ddr3_axp_vars.h:167:4: note: ‘div_ratio1to1’ was previously declared
here
ddr3_dfs.c:46:11: warning: type of ‘div_ratio2to1’ does not match
original declaration [-Wlto-type-mismatch]
ddr3_axp_vars.h:196:4: note: array types have different bounds
ddr3_axp_vars.h:196:4: note: ‘div_ratio2to1’ was previously declared
here
CI managed to trigger this as an error when compiling with LTO for AXP.
Fix this by using values from the header files, which seem to be the
correct ones.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In arch/arm/mach-mvebu/dram.c we always include axp's xor.h for common
XOR definitions, regardless whether we compile for axp or a38x.
But the declaration of this function has a different signature in axp's
xor.h from the one used in a38x' implementation - one parameter is u64
instead of u32. This can result in wrong argument's being passed to that
function on a38x with no one the wiser.
I discovered this when building U-Boot for Turris Omnia with LTO. The
compiler complains about the different signatures being thrown into the
same linking process:
axp/xor.h:67:5: warning: type of ‘mv_xor_mem_init’ does not match
original declaration [-Wlto-type-mismatch]
67 | int mv_xor_mem_init(u32 chan, u32 start_ptr, u32 block_size,
| ^
a38x/xor.c:165:5: note: type mismatch in parameter 3
165 | int mv_xor_mem_init(u32 chan, u32 start_ptr, unsigned long long
| ^
a38x/xor.c:165:5: note: type ‘long long unsigned int’ should match
type ‘u32’
Fix this by changing the type of the block_size argument in the axp's
implementation and header file to the one used in a38x (and upstream
mv-ddr-marvell).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This syncs drivers/ddr/marvell/a38x/ with the master branch of repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the
commit 7c351731d196 ("Merge pull request #29 from pali/sync-a38x-uboot").
This patch was created by following steps:
1. Replace all a38x files in U-Boot tree by files from upstream github
Marvell mv-ddr-marvell repository.
2. Run following command to omit portions not relevant for a38x and ddr3:
files=drivers/ddr/marvell/a38x/*
sed 's/#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)/#ifdef TRUE/' -i $files
unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 -UCONFIG_APN806 \
-UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \
-UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DTRUE $files
3. Manually omit SPDX-License-Identifier changes from this patch as
upstream license in upstream github repository contains long license
texts and U-Boot is using just SPDX-License-Identifier.
After applying this patch, a38x ddr3 code in upstream Marvell github
repository and in U-Boot would be fully identical. So in future applying
above steps could be used to sync code again.
The only change in this patch is removal of dead code and some fixes with
include files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
commit 258be123226f8f5cd516b7813fe201fb7d7416e9 upstream.
At this moment, only page 0 of SPD is being read but to support
smbios, we need to read page 1 also which has more info. In order
to do that, we need to allocate more space.
Signed-off-by: Sujeet Baranwal <sujeet.baranwal@cavium.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Sujeet Kumar Baranwal <Sujeet.Baranwal@cavium.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <judge.packham@gmail.com>
The code was processed with unifdef utility to omit portions not
relevant to A38x and DDR3. This removes usage of many macros, including
A70X0, A80X0 and A3900. It seems that the unifdef utility did not remove
the macros from #else comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Bump version of a38x DDR3 trianing to version 14.0.0 to reflect the
version in the mv-ddr-devel branch of upstream repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
There is a new version numbering system, where after 18.12.0 came
1.0.0, 2.0.0, and so on until 14.0.0. So 14.0.0 is newer than 18.12.0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 56db5d1464b44df10a02b99e615ebd6f6a35c428 upstream.
@pali suggested this change
In commit 6285efb ("mv_ddr: add support for twin-die combined memory
device") was added support for twin-die combined memory device and
default value for explicitly uninitialized structure members is zero, s
also twin_die_combined is initialized to zero. Which means COMBINED
value.
As prior this commit there was no support for twin-die combined memory
device, default value for twin_die_combined should be NOT_COMBINED. This
change change order of enum mv_ddr_twin_die to ensure that NOT_COMBINED
has value zero.
Signed-off-by: heaterC <airyguy@gmx.de>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2bdd12dd68b1f8e27a03a3443ae49a09a14c18e4 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes code in ddr3_training.c.
Import this change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit c8b301463d508c807a33f7b7eaea98bbda4aa35e upstream.
The funtion returnd cs size in byte instead of MB, that cause
calculation error since the caller was expected to get u32 and when he
got above 4G it refers it as 0.
The fix was to get the cs memory size from function as in MB and then
multiply it by 1MB.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit d653b305d0b3da9727c49124683f1a6d95d5c9a5 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 20c89a28548cdab11f88d2ec8936344af0686a1e upstream.
WL phase correcion stage is failing while using bus_width of 16bit, not
to be fix this stage is un-necessary when working with bus_width of 16
bit.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2d3b9437cf38c06c4330e0de07f29476197f5e04 upstream.
The ODT enable heuristic based on active chip-selects is not always
correct. Some board might use two chip-selects, but have only one ODT
line connected. Allow board specific mv_ddr_topology_map to directly set
the ODT configuration register value.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 3908e20c6c520339e9bddb566823ae5e065d5218 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ab9240402a70cc02496683971779e75eff410ab4 upstream.
- function mv_ddr_spd_die_capacity_user_get() has a bug,
since it insert a user memory enum to it,
instead of SPD memory enum (which are different)
- fix: remove mv_ddr_spd_die_capacity_user_get() function.
- memory size with 64 and 32 bit already calculated correctly
at mv_ddr_mem_sz_per_cs_get() function
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Stefan Chulski <Stefan.Chulski@cavium.com>
Reviewed-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6c705ebc0d70f67ed7cae83ad1978c3305ef25be upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header mv_ddr_topology.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 61a8910998d7b553e80f600ebe8147a8b98f0945 upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 32800667b375ebd1f82120da0f3479b1cf52d96d upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit a165037ec26f301be75e1fabc263643683e85255 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently checkpatch is not happy about this file:
total: 14 errors, 2 warnings, 7 checks, 359 lines checked
Improve the coding style so that it can now report:
total: 0 errors, 0 warnings, 6 checks, 360 lines checked
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>