Commit graph

23 commits

Author SHA1 Message Date
Masahiro Yamada
09f3ca3dd5 arm, powerpc: select SYS_GENERIC_BOARD
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-24 13:50:38 -04:00
Vladimir Zapolskiy
f0aa26f006 lpc32xx: remove surplus clock cycle in PL175 WAIT_OEN config
According to ARM PrimeCell PL175 documentation WAIT_OEN config value
is defined without any additional clocks added to the value set by a
client, the change fixes the wrong interface to WAIT_OEN config.

The change also touches a single user of LPC32xx EMC and corrects
configured "output enable delay" value on its side according to the
changed interface.

No functional change intended.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2015-10-11 17:12:13 -04:00
Sylvain Lemieux
89983478bd gpio: lpc32xx: fix issues with port3 gpio
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.

Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
   the second call to "gpio_request" will return -EBUSY.

2) The status of GPO_xx pin report the status of the
   corresponding GPI_xx pin when using the "gpio status" command.

3) The gpio driver may setup the direction register for the wrong
   gpio when calling "gpio_direction_input" (GPI_xx) or
   "gpio_direction_output" (GPO_xx) on port 3; the call to the
   direction is require to use the "gpio status" command.

The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-09-11 17:15:34 -04:00
Vladimir Zapolskiy
bab8d1e228 lpc32xx: remove duplicated DMA_CLK_ENABLE bit definition
Because there is an originally defined CLK_DMA_ENABLE macro in clk.h,
no reason to add another DMA_CLK_ENABLE macro with the same value.

Remove DMA_CLK_ENABLE, since it does not follow naming convention from
the code, this implies renaming of DMA_CLK_ENABLE to CLK_DMA_ENABLE in
lpc32xx/devices.c file.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-09-11 14:05:35 -04:00
Vladimir Zapolskiy
554b0e0d82 lpc32xx: add common USB OHCI defines for all LPC32xx boards
The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-18 13:45:58 -04:00
Sylvain Lemieux
adf8d58d4f usb: lpc32xx: add host USB driver
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:57 -04:00
Vladimir Zapolskiy
327f0d23c8 lpc32xx: move common SLC NAND defines to arch/config.h
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h

The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-18 13:45:55 -04:00
Sylvain Lemieux
980db8ca43 dma: lpc32xx: add DMA driver
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:55 -04:00
Sylvain Lemieux
2783fe6903 arm: lpc32xx: gpio macro for pin mapping
Add LPC32xx GPIO interface macro for pin mapping.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-17 08:11:05 -04:00
Sylvain Lemieux
d75b532a9e arm: lpc32xx: mux: add missing registers
Add missing registers in struct definition.
Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011).

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-17 08:10:53 -04:00
Vladimir Zapolskiy
dcfd37e5ef nand: lpc32xx: add SLC NAND controller support
The change adds support of LPC32xx SLC NAND controller.

LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.

This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.

Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.

The driver can be included to an SPL image.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-12 20:47:33 -04:00
Albert ARIBAUD \(3ADEV\)
412ae53aad lpc32xx: add support for board work_92105
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
  - EEPROM (24M01-compatible)
  - RTC (DS1374-compatible)
  - Temperature sensor (DS620)
  - DACs (2 x MAX518)
- SPI (through SSP interface)
  - Port expander MAX6957
- LCD display (HD44780-compatible), controlled
  through the port expander and DACs

This board has SPL support, and uses the LPC32XX boot
image format.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:39 +02:00
Albert ARIBAUD \(3ADEV\)
981219eebe lpc32xx: add LPC32xx SSP support (SPI mode)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:20 +02:00
Albert ARIBAUD \(3ADEV\)
606f704760 lpc32xx: add GPIO support
This driver only supports Driver Model, not legacy model.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:09 +02:00
Albert ARIBAUD \(3ADEV\)
5e862b9539 lpc32xx: i2c: add LPC32xx I2C interface support
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:07 +02:00
Albert ARIBAUD \(3ADEV\)
c8381bf435 lpc32xx: mtd: nand: add MLC NAND controller
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.

The SPL framework is supported.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:56 +02:00
Albert ARIBAUD \(3ADEV\)
ac2916a224 lpc32xx: add Ethernet support
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:48 +02:00
Vladimir Zapolskiy
0ce3f1f90a ARM: lpc3250: config: add generic board support
The only LPC3250 board works fine with enabled generic board support,
add CONFIG_SYS_GENERIC_BOARD right into the arch config header.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2015-02-16 15:48:36 -05:00
Masahiro Yamada
5d7b131d41 ARM: remove CONFIG_ARM926EJS defines
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).

This commit removes all the defines of CONFIG_ARM926EJS and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Vladimir Zapolskiy
cc35fdbc4d serial: add LPC32X0 high-speed UART devices support
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:21 +02:00
Vladimir Zapolskiy
52f69f818c arm926ejs: add NXP LPC32x0 cpu series support
This change adds initial support for NXP LPC32x0 SoC series.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:21 +02:00