commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MACH_TYPE values for the omap37xx based platforms are no longer
officially valid, so we must not set and pass them. In order to not
reference them but still be able to set the default fdtfile based on the
board detection logic we need to combine the two steps into one.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Adam Ford <aford173@gmail.com>
The autodetect feature doesn't allow users to specify the device tree.
This fix will make it only autodetect if 'fdtimage' is not defined.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
The PBIAS fixing is done in the MMC driver, and doing it in the
the board file conflicts with the driver causing intermittent
hangs on reboot. Remove this from the board file and let
the driver do it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.
Tested on the Logic PD Torpedo + Wireless.
I only changed a handful of devices that used the same syntax as the Logic
board. Appologies if I missed one or stepped on toes. Thanks to Derald Woods
and Alexander Graf.
Signed-off-by: Adam Ford <aford173@gmail.com>
V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c
V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c
V4: Fix subject heading
V3: Remove reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.
V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Logic PD makes four different system on modules. This patch will auto
detect the board type and identify the corresponding device tree image.
V2:
Added 'default:' case to switch statement
Since board_late_init() is defined as int, we now return 0
Signed-off-by: Derald Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
I will take this over from Peter Barada, since I work with it daily
at Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peter Barada <peter.barada@logicpd.com>
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Previously, Omap3_logic assumed X-loader was present. With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot. This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <nm@ti.com>
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini@ti.com>
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch across possible values, which
returns the zoom2_serial_deviceN . With such adjustment in place,
the exported prototypes in serial.h can be safely removed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
The initial checkin dropped pinmux setup for GPMC pins A6-A10, D0-D7 and
NCS1/2 necessary to access LAN92xx on Logic OMAP35x/DM37x modules.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
